Lutron Electronics Sivoia QED User manual

Sivoia QEDTM
Installation
Instructions
Dual Mount
Roller Shade
Note: If installing a coupled system,
use In-Line Coupled Roller
Shade Addendum as the
primary installation guide.

Sivoia QEDTM |dual mount roller shade
Installation Instructions
SIVOIA QEDTM Dual Mount Installation Instructions 1
Tools Required:
Tape Measure 1/4” Hex-Head Driver
Wire Cutter/Stripper Level
Pliers Power Drill
#2 Phillips Screwdriver
Box Contents:
Sivoia QED Roller Shade (2) Dual Sub-Brackets (if applicable)
Left and Right Side Shade Brackets (attached)
(16) Mounting Screws
(#8x1-3/4" (#8x44mm) Hex Head Screws)
(2) 7-Pin Terminal Blocks
(4) Extra Retaining Screws
(#6x1/4" (#6x6mm) Phillips Head Screws)
(Actual Size)
(Actual Size)
(4) 4” (102mm) Cable Ties (4) 7” (178mm) Cable Ties
Notes:
1) For In-Line Coupled Shade Systems, begin with Sivoia QED In-Line Coupled Roller Shade
Addendum, P/N 045-048. The Addendum will indicate when to use this document.
2) Complete wiring and programming information can be found in the Sivoia QED Wire and
Programming Guide, P/N 045-038 or at www.lutron.com.
3) The Electronic Drive Unit (EDU) will need to be powered to complete installation.

SIVOIA QEDTM Dual Mount Installation Instructions 2
11 Match Shade to Window
System Width
System Height
System Width System Height
Confirm system dimensions on
package label and window
dimensions to verify appropriate
window/shade combination.
System width must be less than
or equal to dual width.
glass
1.1
Orient sub-bracket for installation
as shown to right. The shade and
sub-brackets mount to the inside
surface of the dual that is
OPPOSITE the glass.
The fabric drop should be closest
to the glass.
1.2
Package Label
ceiling

SIVOIA QEDTM Dual Mount Installation Instructions 3
2Pre-drill for Cable
Determine where to drill for cable access. See options below.
Two lengths of 12-18" (305-457mm) of cable should exit the ceiling, jamb or
either wall on the EDU side of the shades.
2.1
Ceiling
Drill for cables 1 1/2" - 3 1/2" (38-89mm) from back
and 1 1/4" - 2" (32-51mm) from end of system.
Jamb
Drill for cables 5 1/4" - 6" (133-152mm) from back
and 4 1/4" - 5" (108-127mm) from top of system.
Wall
Drill for cables 1 1/2" - 2 1/2" (38-64mm) from top
and 1 1/2" - 2 1/2" (38-64mm) from end of system.
Ceiling Wall
Wall
Drill for one cable 2 1/2" - 3 1/2" (64-89mm) from top
and 1 1/2" - 2 1/2" (38-64mm) from end of the system.
Drill for second cable 6 1/2" - 7 1/2" (165-191mm) from
top and 1 1/2" - 2 1/2" (38-64mm) from end of system.
Wall
Jamb
Glass
GlassGlass
Glass
Non
Glass
Side
Non
Glass
Side

3Mount Sub-Brackets
SIVOIA QEDTM Dual Mount Installation Instructions 4
Mount sub-brackets using
appropriate fasteners.
3.3
Verify that sub-brackets are
oriented correctly. Hanging
features should be on the
side opposite the glass.
3.2
3/4”
(19mm)
Glass
Fabric Width
System Width
WARNING:
The sub-brackets for each shade
tube should be mounted to
support a weight of at least 300
pounds (136kg). The fasteners
provided with the sub-brackets
may not be appropriate for use in
all applications.
Use fabric alignment holes to
position the sub-bracket right
to left. The fabric alignment
holes will line up with the out-
side edge of the shade tube.
Note: Fabric edge may not
line up with the edge of
the tube.
3.1

SIVOIA QEDTM Dual Mount Installation Instructions 5
4Wire 7-pin Terminal Blocks
Wire the 7-pin terminal block
(provided) to the cable.
Note: SVQ-CBL-250 shown
Repeat for each cable.
Strip jacket off entire exposed
length of both cables.
(12-18” or 305-457mm)
4.1
4.2
To EDU
Connector
EGND (Yellow/Green)
24 VAC (Red)
24 VAC (Red/White)
MUX (Purple)
MUX (Gray)
+12 VDC (Blue)
Common (Yellow)

SIVOIA QEDTM Dual Mount Installation Instructions 6
5Hang First (Top) Shade
Hook the lip of each shade
bracket onto the top of
each sub-bracket.
5.2
Swing shade down until
bottom of shade brackets
rest against sub-brackets.
5.3
5.4
Note: Ensure cable is kept
outside the shade bracket.
Route cable wires from wall,
ceiling or jamb between the
shade bracket and sub-bracket
being careful not to pinch wire.
Remove retaining screws
from shade brackets.
WARNING:
Shades wider than 4ft (1.2m)
require two people to install.
5.1
Note: If installing a coupled
shade system, install the
shade with the EDU first.
Note: Leave protective
wrapping on shade during
installation.

SIVOIA QEDTM Dual Mount Installation Instructions 7
6Center and Secure Shade
Insert and tighten retaining
screws on BOTH brackets
to secure the shade into
position. Screws should be
tightened down all the way.
6.3
WARNING:
After installing retaining
screws, gently push up
and pull down on the
roller shade to ensure a
secure installation.
Move shade left or
right until centered.
6.1
Move shade left or
right until centered.
6.1
6.2 ceiling
WARNING:
Shade is not secured to
the wall during the
adjustment procedure.
Extreme movement from
side-to-side may cause
shade to fall. Attention
should be paid to the
shade brackets’ engage-
ment into the sub-brack-
et as side-to-side move-
ment is not restricted at
this point. Shades wider
than 4ft (1.2m) require
two people to center the
shade.
retaining
screw

SIVOIA QEDTM Dual Mount Installation Instructions 8
7Adjust Shade Level
Turn leveling screw
to raise or lower idler
side of shade until
level.
7.1
Adjust shade projection from
window so that it clears any
window trim or hardware
when operating.
7.2
Confirm roller tube turns
freely without rubbing on
anything.
7.3

SIVOIA QEDTM Dual Mount Installation Instructions 9
8Connect Terminal Blocks
ceiling
Plug 7-pin terminal
block on cable into
EDU terminal block
attached to shade
bracket
Note: EDU terminal block
clips onto shade bracket to
hold connected terminal
block in place.
8.1
Ensure terminal blocks are
oriented as shown.
8.2
Secure terminal blocks
with 7” (178mm) cable tie.
8.3
Use 4” (102mm)
Cable Ties to dress
wires to prevent
them from rubbing
against shade fabric.
8.4
7” (178mm) cable tie