LuxaFlex PowerView M50 Series User manual

PowerView™AC Motor
by LUXAFLEX®WINDOW FASHIONS

CONTENTS
GETTING STARTED
Getting Started................................................................................................................ 1
Remote Control Overview................................................................................................. 2
Using Multiple remotes within a home (Copying Network ID) .............................................. 4
Programming Overview.................................................................................................... 5
PROGRAMMING
STEP 1 — Join a Shade to a Group ................................................................................ 5
STEP 2 — Reverse the Motor Direction (If Necessary) ...................................................... 6
STEP 3 — Set the Motor Upper Limit ............................................................................... 6
STEP 4 — Set the Motor Lower Limit............................................................................... 7
STEP 5 — Set a Favourite Position (Optional) ................................................................... 8
STEP 6 — Creating a Duplicate Remote........................................................................... 8
STEP 7 — Test the Motors and PowerView Shade Network ............................................... 9
APPENDIX A
Clear Motor Limits......................................................................................................... 10
Remove a Shade from a Group....................................................................................... 10
Deactivate the remote’s auto-wake feature ..................................................................... 11
Reset Shade Network Programming ............................................................................... 11
Reset to Factory Default................................................................................................. 11
Control the motor with Dry Contacts (M40 Motor only) ..................................................... 12
Hunter Douglas Australia
338 Victoria Rd Rydalmere, NSW, 2116, Australia
PowerView has been certified as complying with ACMA'S regulatory requirements.
© Copyright 2016 Hunter Douglas Limited [ABN 98 009 675 709]
® Luxaflex, PowerView and Pebble are registered Trade Marks of Hunter Douglas •10/2016

WARNING: Motors do not have default limits set. Limits must be set to enable normal operation. If
operated without limits, the blind could be damaged by rolling over the top or wrapping backwards
on the roller.
KEY COMPONENTS
The following items are required for single shade or multiple shade setup.
PowerView AC motor(s) with roller shade(s)
PowerView Pebble Remote or PowerView Surface Remote
Manual Control Button
M40 Series
Dry Contact
Input
RF Antenna
Manual Control Button
RF Antenna
M50 Series
CAUTION: Do not damage the RF antenna. For best RF performance, the antenna should maintain as much separation from a
conductive surface as possible.
GETTING STARTED
1
GETTING STARTED

POWERVIEW™ PEBBLE® REMOTE
Ergonomically designed, the PowerView Pebble hand-held remote is available
in seven on-trend colours to complement your home décor.
POWERVIEW SURFACE REMOTE
The sleek PowerView Surface is wall-mounted so you know your remote is
always right where you left it.
REMOTE MODULE FRONT
RIGHT ARROW
Super Quiet Mode.
LEFT ARROW
Super Quiet Mode.
Favourite
Shade position
STOP
Press and
hold for
program
mode.
GROUP 1
GROUP 2
GROUP 3 GROUP 4
GROUP 5
GROUP 6
CLOSE
OPEN
REMOTE MODULE
(BACK COVER REMOVED)
BATTERY
COMPARTMENT
3V CR 2032
BATTERY
COMPARTMENT
3V CR 2032
RESET
BUTTON
REMOTE CONTROL OVERVIEW
2
REMOTE CONTROL OVERVIEW

REMOTE MODULE
(BACK COVER REMOVED)
Important: The PowerView Remote will not operate a window covering until
the window covering has been added to a GROUP.
GETTING STARTED
First, activate the remote by pulling both plastic tabs from the back battery
compartment.
Inserting the remote module into the PowerView Pebble
(hand-held):
1. Centre the Hunter Douglas logo on the remote module above the
indentation on the bottom rim of the Pebble.
2. Align the ribs on the remote module with the grooves on the Pebble.
3. Gently push the remote module into the Pebble until it
is snug.
MOUNTING THE POWERVIEW SURFACE:
1. Choose a location to mount the Surface.
2. Orient the Surface mounting plate so that the Hunter Douglas logo
is horizontal and level. Mark screw holes.
3. If you are mounting the Surface onto drywall, use a 6mm drill bit
to drill pilot holes. Tap drywall anchors into the pilot holes until the
flange of the anchor is flush with the drywall.
4. If you are mounting the Surface onto wood, use a 3mm
drill bit to drill the screw holes.
5. Attach the Surface mounting plate using the screws provided.
6. Align the Surface ring with its mounting plate and twist the Surface ring clockwise to lock it in place. Inserting the
remote module in the Surface:
1. Align the ribs on the remote module with the grooves on the Surface.
2. Gently push the remote module into the Surface until it is snug.
REMOTE CONTROL OVERVIEW
3
REMOTE CONTROL OVERVIEW

Each PowerView Remote comes with its own unique
Radio Frequency (Network) ID. If multiple remotes (ie.
PowerView Pebble and/or PowerView Surface remotes)
will be used in the home, it is necessary to establish
a single PowerView Shade Network ID for all remotes
before any window covering programming is done. This
is to ensure that if a PowerView Hub, PowerView Scene
Controller or PowerView Repeater(s) will be used in the
future, it can be used to operate previously programmed
window coverings in the home and be used in conjunction
with all the remotes on a single, unified network.
1. SELECT the initial Network remote. This will be the
source remote from which a unified PowerView Shade
Network will be established for the home.
NOTE: As a unified network has not yet been
established, it does not matter which available remote
you choose to use to create a PowerView Shade
Network.
2. SELECT the target remote.
3. REMOVE the back cover on the target remote.
4. Using a ball point pen, PRESS and HOLD the
recessed Reset button on the back of the target
remote for six seconds.
NOTE: The Group numbers (1-6) buttons will flash
twice on the press of the Reset button, then again at
six seconds.
5. REINSTALL the back cover onto the target remote.
6. PRESS and HOLD (Stop) on the source remote,
until indicator lights begin to blink.
NOTE: This puts the source remote in Programming
Mode. Indicator lights on the source remote will
continue to blink for 20 seconds following each set of
commands, allowing additional target remotes to be
networked.
7. With the source remote in Programming mode, PRESS
and continue to HOLD (Stop) on the target remote.
Complete steps 8 and 9 at the same time.
8. PRESS and RELEASE (Stop) on the source remote.
9. RELEASE (Stop) on the target remote.
NOTE: The Group numbers (1-6) on the target remote will flash twice to indicate that it has been networked to the
source remote.
10. PRESS and HOLD (Stop) on the source remote until the indicator lights stop blinking.
USING MULTIPLE REMOTES WITHIN A HOME (PAIRING REMOTES TO A SINGLENETWORK ID)
1. 2.
Source Target Target
5. 6. Source
3. 4.
Target
Target
8. 9.
Source
7.
Target Target
10. Source
4
USING MULITPLE REMOTES

USING MULTIPLE REMOTES WITHIN A HOME (PAIRING REMOTES TO A SINGLENETWORK ID)
To program your PowerView AC motor and roller shade, you will need to perform the following 9 steps:
STEP 1: Join a Shade to a Group
STEP 2: Reverse the Motor Direction (If Necessary)
STEP 3: Set the Motor Upper Limit
STEP 4: Set the Motor Lower Limit
STEP 5: Set a Favourite Position (Optional)
STEP 6: Creating a Duplicate Remote
STEP 7: Test the Motors and PowerView Shade Network
STEP 1 — JOIN A SHADE TO A GROUP
1. Remote: press and hold STOP for 6 seconds to put the remote into program mode.
The backlit buttons on the remote will flash to
indicate it is in program mode.
2. Remote: press and release the desired GROUP
number (1 – 6).
The backlit GROUP number will flash to show it is
selected.
3. Motor: press and hold the manual control button
located on the motor head.
4. Remote: while continuing to press the manual control button,
press and release OPEN on the remote.
The shade will move twice to indicate it has joined the group.
5. Motor: release the manual control button.
6. Remote: press and hold STOP for 6 seconds to exit
program mode. The lights will stop flashing.
WARNING: The AC motor will not operate correctly until limits are set (Step 3 and Step 4).
5
PROGRAMMING OVERVIEW
PROGRAMMING OVERVIEW

IMPORTANT: Be sure no end limits are set on the motor. If one or both limits are set, you cannot change the motor direction.
See Appendix A for instructions to clear limits.
1. Remote: deselect all GROUP numbers
2. Motor: press and hold the manual control button
located on the motor head.
3. Remote: while continuing to press the
manual control button, press and release STOP
on the remote.
4. The shade will move twice to indicate it has
reversed motor direction.
NOTE: If end limits were already set, the motor will not
move, indicating the motor direction did not change.
NOTE: Verify that all GROUP lights are turned off on the
remote, clear both limits, and try again.
5. Motor: release the manual control button.
3. SET THE MOTOR UPPER LIMIT
NOTE: When end limits are not set, the motor responds to OPEN or CLOSE on the remote with single, small
movements.
1. Move the shade to the desired upper limit.
On the remote, use the OPEN, CLOSE, or LEFT
or RIGHT ARROW buttons to fine tune desired
position.
On the motor, use the manual control button or dry
contact input (M40 Series only).
2. Remote: press and hold STOP for 6 seconds
to put the remote into program mode.
The backlit buttons on the remote will flash to
indicate it is in program mode.
3. Remote: deselect all GROUP numbers.
4. Motor: press and hold the manual control button
located on the motor head.
5. Remote: while continuing to press the manual
control button, press and release OPEN on the remote.
The shade will move twice to indicate the upper limit is set.
6. Motor: release the manual control button.
7. Remote: press and hold STOP for 6 seconds to exit program mode.
The lights will stop flashing.
IMPORTANT: Verify that the upper limit is set. If not, deselect all GROUP numbers and
repeat Step 3.
NOTE: When end limits are not set, the motor responds to OPEN or CLOSE on the remote with single, small
movements.
IN PROGRAM MODE:
Deselect all GROUP
numbers.
IN PROGRAM MODE:
Deselect all GROUP
numbers.
6
2. REVERSE THE MOTOR DIRECTION
REVERSE THE MOTOR DIRECTION / SET THE MOTOR UPPER LIMIT

1. Move: the shade to the desired lower limit.
On the remote, use the OPEN, CLOSE, LEFT or RIGHT, ARROW to fine
tune desired position.
On the motor, use the manual control button or dry
contact input (M40 Series only).
2. Remote: press and hold STOP for 6 seconds to put the remote
into program mode.
The backlit buttons on the remote will flash to indicate it is in program
mode.
3. Remote: deselect all GROUP numbers.
4. Motor: press and hold the manual control button located on the
motor head.
5. Remote: while continuing to press the manual control button,
press and release CLOSE on the remote.
The shade will move twice to indicate the lower limit is set.
6. Motor: release the manual control button.
7. Remote: press and hold STOP for 6 seconds to exit program
mode.
The lights will stop flashing.
IMPORTANT: Verify that the lower limit is set. If not,
deselect all GROUP numbers and repeat Step 4.
NOTE: After the upper and lower limits are set, the motor will have one
Favourite position, which is set at 50% open by default. Setting a new Favourite position overwrites any previous
setting.
IN PROGRAM MODE:
Deselect all GROUP
numbers.
IN PROGRAM MODE:
Deselect all GROUP
numbers.
7
4. SET THE MOTOR LOWER LIMIT
SET THE MOTOR LOWER LIMIT

1. Move the motor to the desired position.
2. Remote: press and hold STOP for 6 seconds to
put the remote into program mode.
The backlit buttons on the remote will flash to
indicate it is in program mode.
3. Remote: deselect all GROUP numbers.
4. Motor: press and hold the manual control button
located on the motor head.
5. Remote: while continuing to press the manual control button, press
and release FAVOURITE on the remote. The shade will move twice to indicate it has set this shade position as your
FAVOURITE.
6. Motor: release the manual control button.
7. Remote: press and hold STOP for 6 seconds to exit
program mode.
The lights will stop flashing.
IMPORTANT: Verify that the FAVOURITE position is set at the desired position.
6. CREATING A DUPLICATE REMOTE
A duplicate remote will operate the same set of window coverings and GROUPS as the original remote.
1. Remove the back cover from the new remote.
2. Press and hold the recessed Reset button for 6 seconds, until the GROUP buttons flash two separate times. Reinstall the
back cover.
3. Press and hold STOP for 6 seconds on the original remote to put it in programming mode. The
backlit buttons on the remote will flash to indicate it is in programming mode.
4. While pressing and holding ALL on the new remote, press and release STOP on the original
remote.
5. The backlit group buttons on the duplicate remote will flash twice to indicate all of the
information from the original remote has been copied.
6. Press and hold STOP for 6 seconds on the original remote to exit program mode.
8
5. SET A FAVOURITE POSITION
SET A FAVOURITE POSITION / CREATING A DUPLICATE REMOTE

Use the remote control to verify the following settings for all shades in the PowerView Shade Network.
Verify each shade is joined to the correct GROUP number.
Press ALL to move all shades.
Press GROUP 1 – 6 to select specific shades to operate.
1. Verify that the motor direction is correctly set for each shade.
Press ALL, then press OPEN on the remote.
All shades should move in the up direction.
2. Verify that the upper limit is correctly set for each shade.
Press ALL, then press OPEN on the remote.
All shades should stop at the correct upper limit.
3. Verify that the lower limit is correctly set for each shade.
Press ALL, then press CLOSE on the remote.
All shades should stop at the correct lower limit.
4. Verify that the FAVOURITE position is correctly set for each shade.
Press ALL, then press FAVOURITE on the remote.
All shades should stop at the correct FAVOURITE position.
7. TEST THE MOTORS AND POWERVIEW SHADE NETWORK
9
TEST THE MOTORS AND POWERVIEW SHADE NETWORK

Clear Top Limit
1. Remote: deselect all GROUP numbers.
2. Motor: press and hold the manual control
button located on the motor head.
3. Remote: while continuing to press the manual
control button, press and release OPEN on
the remote.
The shade will move twice to indicate the upper
limit is cleared.
4. Motor: Release the manual control button.
NOTE: To set Top Limit refer to Step 3.
Clear Lower Limit
1. Remote: deselect all GROUP numbers.
2. Motor: press and hold the manual control button
located on the motor head.
3. Remote: while continuing to press the
manual control button, press and release
CLOSE on the remote.
The shade will move twice to indicate the
lower limit is cleared.
4. Motor: Release the manual control button.
NOTE: To set Top Limit refer to Step 4.
REMOVE A SHADE FROM A GROUP
NOTE: Only one GROUP number can be removed at a time.
1. Remote: press and hold STOP for 6 seconds to
put the remote into program mode.
The backlit buttons on the remote will flash to
indicate it is in program mode.
2. Remote: press the desired GROUP number (1 – 6).
The backlit GROUP number will flash to show it is
selected.
3. Motor: press and hold the manual control button
located on the motor head.
4. Remote: while continuing to press the manual control button, press and release CLOSE on the remote. The shade
will move twice to indicate it has been removed from the group.
5. Motor: Release the manual control button.
6. Remote: Press and hold STOP for 6 seconds to exit program mode.
The lights will stop flashing.
NOTE: To add shade to a new group refer to Step 1.
IN PROGRAM MODE:
Deselect all GROUP
numbers.
IN PROGRAM MODE:
Deselect all GROUP
numbers.
10
CLEAR MOTOR LIMITS
IN PROGRAM MODE:
One GROUP number
must be selected.
CLEAR MOTOR LIMITS / REMOVE A SHADE FROM A GROUP

11
DEACTIVATING THE REMOTE’S AUTO-WAKE FEATURE
The auto-wake feature activates the backlights on the remote, whenever the remote is handled. This feature is useful for
immediately seeing which shade group buttons were activated last, but deactivating this feature will help to conserve battery
life.
1. PRESS and HOLD the Group 6 button on the remote for approximately six seconds.
2. The Group numbers (1-6) will blink once to indicate the auto-wake feature has been disabled.
3. To reactivate the Auto-wake feature follow step 1.
RESET SHADE NETWORK PROGRAMMING
The shade network programming reset erases all remote GROUP assignment programming stored in the shade. The reset will
also remove the shade from its current PowerView Shade Network, preventing any input device from operating the shade. The
primary use is during installation to correct GROUP and Network assignments. This reset does not affect motor limits, motor
direction, or the FAVOURITE position.
1. Motor: press and hold the manual control button located on the motor head for 12 seconds.
The shade will move twice after 6 seconds, then again after 12 seconds.
2. Motor: Release the manual control button.
Refer to “JOIN A SHADE TO A GROUP” refer to step 1.
RESET TO FACTORY DEFAULT
The factory default reset erases all information stored in a shade motor. The motor is returned to its factory default settings
of no network programming, no limits, and the motor direction is reset. The default FAVOURITE position will be at 50% after
limits are set.
1. Motor: press and hold the manual control button located on the motor head for 18 seconds.
The shade will move twice after 6 seconds, then again after 12 seconds, and then again after 18 seconds.
2. Motor: Release the manual control button.
Refer to “JOIN A SHADE TO A GROUP” Stage 1 to program the shade into a group, then reverse motor direction (if
necessary), set limits, and set a new FAVOURITE position (optional).
DEACTIVATE REMOTE/ /RESET NETWORK / RESET FACTORY DEFAULT

12
Manual Control Button
Dry Contact
Input
RF Antenna
Manual
C
ontrol Button
D
ry Contac
t
I
n
p
u
t
RF Antenn
a
CLOSE
COMMON
OPEN
Open
Short the OPEN dry contact to COMMON and then release.
The motor moves in the OPEN direction.
Close
Short the CLOSE dry contact to COMMON and then release.
The motor moves in the CLOSE direction.
Stop
With the motor moving, short the OPEN or CLOSE dry contact to common and
then release.
This stops the motor, if the motor is moving in the direction of the dry contact
command that is shorted.
Alternate STOP (short all 3 contacts)
Simultaneously short the OPEN and CLOSE dry contacts to COMMON for less
than 1.5 seconds, then release.
This stops the motor, if the motor is moving.
Go to the FAVOURITE Position (short all 3 contacts)
Simultaneously short the OPEN and CLOSE dry contacts to COMMON for more than 1.5 seconds, then release.
The motor goes to the FAVOURITE position (if both end limits are set).
CONTROL THE MOTOR WITH DRY CONTACTS (M40 SERIES MOTOR ONLY)
CONTROL THE MOTOR WITH DRY CONTACTS