Luxul Epic 5 User manual
Fold Fold Fold
READ ME FIRST
QUICK INSTALL GUIDE
Epic 5
High-Performance Gigabit Router
ABR-5000
Includes:
High-Performance Gigabit Router
Rack Mount Kit
Rubber Feet
Power Cord
SETUP AND CONFIGURATION
1Physical Installation
The Epic 5 can be rack-mounted or used as a desktop router. Install the
router in a stable/safe place to avoid any possible damage. Make sure there is
adequate space around the router for ventilation and proper heat dissipation.
Avoid placement in direct sunlight. Do not place heavy articles on the router
and verify the ground connection of the outlet is functioning properly.
Desktop/Shelf Installation
For desktop/shelf installation, attach the four rubber feet to the corner
indentations on the bottom of the router, then place the router on
a solid, level platform.
Rack Installation
Use the included L brackets for convenient installation in a 19-inch server or AV
rack. As shown below, use four screws to attach the L-shaped brackets on both
sides of the router then mount it horizontally in the rack. Use your desired
hardware to ax the router supports to the rack.
Install Brackets for Rack-Mounting Attach Feet for Desktop Installation
2Connecting Ethernet and Power
Before you attempt to configure the router, test the Internet connection to
verify that it is functioning properly. Once Internet access is confirmed to
be working, follow the steps below for installation and configuration.
Connecting Ethernet
Luxul recommends at least Cat-5e unshielded twisted pair (CAT5e UTP)
cabling. To ensure best performance and stable data transmission at 1000
Mbps, use Category-6 unshielded twisted pair (CAT6 UTP).
1. Connect the WAN: Connect the Internet cable from a telco/ISP
modem/router to the dedicated WAN 1 port on the Epic 5.
2. Connect the LAN: Connect a cable from the dedicated LAN 1 port on
the Epic 5 to a switch, access point, or computer.
For best performance, and to maximize available ports, Luxul recommends
connecting all LAN devices to a Luxul switch, then connecting that switch
to the Epic 5 LAN port via a single Ethernet cable.
nNOTE: Connect all LAN devices to a Luxul switch, then connect that
switch to the router for best results.
Connecting Power
Use the included power cable to connect the router to a surge-protected
outlet. The AC input socket and power switch are on the rear panel. The
built-in power supply supports 100~240VAC at 50/60Hz.
Sales
801-822-5450
Technical Support
801-822-5450
LUX-QIG-ABR-5000-v7
Copyright and Trademark Notices
No part of this document may be modified or adapted in any way, for any purposes without permission in
writing from Luxul. The material in this document is subject to change without notice. Luxul reserves the
right to make changes to any product to improve reliability, function, or design. No license is granted, either
expressly or by implication or otherwise under any Luxul intellectual property rights. An implied license
only exists for equipment, circuits and subsystems contained in this or any Luxul product.
© Copyright 2016 Luxul. All rights reserved. The name Luxul, the Luxul logo, the Luxul logo mark and Simply
Connected are all trademarks and or registered trademarks of Luxul Wireless, Inc. All other trademarks and
registered trademarks are property of their respective holders.
Fold Fold Fold
READ ME FIRST
QUICK INSTALL GUIDE
Epic 5
High-Performance Gigabit Router
ABR-5000
Includes:
High-Performance Gigabit Router
Rack Mount Kit
Rubber Feet
Power Cord
SETUP AND CONFIGURATION
1Physical Installation
The Epic 5 can be rack-mounted or used as a desktop router. Install the
router in a stable/safe place to avoid any possible damage. Make sure there is
adequate space around the router for ventilation and proper heat dissipation.
Avoid placement in direct sunlight. Do not place heavy articles on the router
and verify the ground connection of the outlet is functioning properly.
Desktop/Shelf Installation
For desktop/shelf installation, attach the four rubber feet to the corner
indentations on the bottom of the router, then place the router on
a solid, level platform.
Rack Installation
Use the included L brackets for convenient installation in a 19-inch server or AV
rack. As shown below, use four screws to attach the L-shaped brackets on both
sides of the router then mount it horizontally in the rack. Use your desired
hardware to ax the router supports to the rack.
Install Brackets for Rack-Mounting Attach Feet for Desktop Installation
2Connecting Ethernet and Power
Before you attempt to configure the router, test the Internet connection to
verify that it is functioning properly. Once Internet access is confirmed to
be working, follow the steps below for installation and configuration.
Connecting Ethernet
Luxul recommends at least Cat-5e unshielded twisted pair (CAT5e UTP)
cabling. To ensure best performance and stable data transmission at 1000
Mbps, use Category-6 unshielded twisted pair (CAT6 UTP).
1. Connect the WAN: Connect the Internet cable from a telco/ISP
modem/router to the dedicated WAN 1 port on the Epic 5.
2. Connect the LAN: Connect a cable from the dedicated LAN 1 port on
the Epic 5 to a switch, access point, or computer.
For best performance, and to maximize available ports, Luxul recommends
connecting all LAN devices to a Luxul switch, then connecting that switch
to the Epic 5 LAN port via a single Ethernet cable.
nNOTE: Connect all LAN devices to a Luxul switch, then connect that
switch to the router for best results.
Connecting Power
Use the included power cable to connect the router to a surge-protected
outlet. The AC input socket and power switch are on the rear panel. The
built-in power supply supports 100~240VAC at 50/60Hz.
Sales
801-822-5450
Technical Support
801-822-5450
LUX-QIG-ABR-5000-v7
Copyright and Trademark Notices
No part of this document may be modified or adapted in any way, for any purposes without permission in
writing from Luxul. The material in this document is subject to change without notice. Luxul reserves the
right to make changes to any product to improve reliability, function, or design. No license is granted, either
expressly or by implication or otherwise under any Luxul intellectual property rights. An implied license
only exists for equipment, circuits and subsystems contained in this or any Luxul product.
© Copyright 2016 Luxul. All rights reserved. The name Luxul, the Luxul logo, the Luxul logo mark and Simply
Connected are all trademarks and or registered trademarks of Luxul Wireless, Inc. All other trademarks and
registered trademarks are property of their respective holders.
Fold Fold Fold
READ ME FIRST
QUICK INSTALL GUIDE
Epic 5
High-Performance Gigabit Router
ABR-5000
Includes:
High-Performance Gigabit Router
Rack Mount Kit
Rubber Feet
Power Cord
SETUP AND CONFIGURATION
1Physical Installation
The Epic 5 can be rack-mounted or used as a desktop router. Install the
router in a stable/safe place to avoid any possible damage. Make sure there is
adequate space around the router for ventilation and proper heat dissipation.
Avoid placement in direct sunlight. Do not place heavy articles on the router
and verify the ground connection of the outlet is functioning properly.
Desktop/Shelf Installation
For desktop/shelf installation, attach the four rubber feet to the corner
indentations on the bottom of the router, then place the router on
a solid, level platform.
Rack Installation
Use the included L brackets for convenient installation in a 19-inch server or AV
rack. As shown below, use four screws to attach the L-shaped brackets on both
sides of the router then mount it horizontally in the rack. Use your desired
hardware to ax the router supports to the rack.
Install Brackets for Rack-Mounting Attach Feet for Desktop Installation
2Connecting Ethernet and Power
Before you attempt to configure the router, test the Internet connection to
verify that it is functioning properly. Once Internet access is confirmed to
be working, follow the steps below for installation and configuration.
Connecting Ethernet
Luxul recommends at least Cat-5e unshielded twisted pair (CAT5e UTP)
cabling. To ensure best performance and stable data transmission at 1000
Mbps, use Category-6 unshielded twisted pair (CAT6 UTP).
1. Connect the WAN: Connect the Internet cable from a telco/ISP
modem/router to the dedicated WAN 1 port on the Epic 5.
2. Connect the LAN: Connect a cable from the dedicated LAN 1 port on
the Epic 5 to a switch, access point, or computer.
For best performance, and to maximize available ports, Luxul recommends
connecting all LAN devices to a Luxul switch, then connecting that switch
to the Epic 5 LAN port via a single Ethernet cable.
nNOTE: Connect all LAN devices to a Luxul switch, then connect that
switch to the router for best results.
Connecting Power
Use the included power cable to connect the router to a surge-protected
outlet. The AC input socket and power switch are on the rear panel. The
built-in power supply supports 100~240VAC at 50/60Hz.
Sales
801-822-5450
Technical Support
801-822-5450
LUX-QIG-ABR-5000-v7
Copyright and Trademark Notices
No part of this document may be modified or adapted in any way, for any purposes without permission in
writing from Luxul. The material in this document is subject to change without notice. Luxul reserves the
right to make changes to any product to improve reliability, function, or design. No license is granted, either
expressly or by implication or otherwise under any Luxul intellectual property rights. An implied license
only exists for equipment, circuits and subsystems contained in this or any Luxul product.
© Copyright 2016 Luxul. All rights reserved. The name Luxul, the Luxul logo, the Luxul logo mark and Simply
Connected are all trademarks and or registered trademarks of Luxul Wireless, Inc. All other trademarks and
registered trademarks are property of their respective holders.
Fold Fold Fold
3Access and Setup
Default IP Address
The Epic 5’s default IP address is 192.168.0.1. This can be modified,
however, we recommend you retain the default IP address if possible
for hassle-free installation of other Luxul products.
nNOTE: In the event another device on your network shares the
192.168.0.1 address, you’ll need to reassign the device’s IP
address or remove it from the network.
Connecting a Client Device
Connect a client device to one of the router LAN ports or to a switch
that is connected to a router LAN port. The DHCP server on the router is
configured by default. If your client device is set to obtain an IP address
automatically, no further configuration is required and you’re ready to log in.
nNote: Visit http://luxul.com/ip-addressing to learn more about
changing your computer’s IP address and getting connected.
Logging In
To access the router web configuration, open your web browser and enter
the router’s default 192.168.0.1 IP address in the address field. Log in to the
router using the default user name and password:
Default IP: 192.168.0.1
Username: admin
Password: admin
Select the menu items on the left to view and/or modify the configuration.
For information on configuring the Epic 5 and routers in general, review
the Support Resources at luxul.com.
4Hardware Operation
The front panel of the router features Power, System and USB LEDs; and port
status indicators for each of the router’s Ethernet ports.
The rear panel of the router features seven RJ-45 Ethernet ports: Two dedicated
WAN ports and five dedicated LAN ports. Using the two dedicated WAN
ports, the router can be connected to two independent Internet connections
simultaneously.
The rear panel also features a power switch and socket, recessed Reset button,
and a switch for selecting front-panel LED colors (blue/green/o) to match
other equipment in an audio/video rack.
Plug a USB flash drive or hard drive into the USB 3.0 port and configure the
built-in file/DLNA server to serve files to LAN-connected client devices.
The Console port supports advanced command-line functionality, but requires
a special cable. Contact support if your application requires a command line.
nNote: The Console port is not an Ethernet port. A special cable is
required for use. Contact support for more information.
Front Panel
Back Panel
Reset Button
The Reset button (located on the rear panel) can be used to reset (reboot) the
router, restore the router to default settings, or restore the router to factory
default software version and settings.
XTo Reboot the Router: With the Epic 5 powered on and running, briefly
press and release the Reset button. The router will reboot. When the System
LED flashes like a heartbeat, the unit is ready.
cCAUTION: Do not hold the button for more than three seconds.
Doing so may erase all settings and restore factory defaults.
XTo Restore the Default Settings: With the router powered on and running,
press and hold the Reset button for 5 seconds, then release the button.
The router will restore its default configuration and reboot. The software
version will not change. When the System LED flashes like a heartbeat, the
unit is ready.
cCAUTION: Restoring default settings will remove any/all
custom configuration.
XTo Restore Factory Software: With the router powered o, press
and hold the Reset button, turn the router on, and continue holding the
Reset button until the System LED turns on. The device will completely
reflash itself back to the factory default software version and settings.
wWARNING: Restoring factory software will remove any/all
custom configuration and remove newer firmware.
LED Indicators
Indicator & State Description
POWER On / SYSTEM O
POWER On / SYSTEM On
POWER On / SYSTEM Blinking
POWER On / SYSTEM Heartbeat
POWER O / SYSTEM O
Epic 5 is powered on and booting.
Loading operating system.
OS loaded; finishing boot process.
Booting finished/operating normally.
Epic 5 not powered.
USB On
Blinking
A USB device is connected.
USB device activity.
WAN/
LAN
Front
Top Row On
Bottom Row On
Flashing
10/100 Mbps device connected.
1000 Mbps device connected.
Data packets are being transferred.
WAN/
LAN
Rear
Yellow On
Green On
Flashing
10/100 Mbps device connected.
1000 Mbps device connected.
Data packets are being transferred.
Fold Fold Fold
3Access and Setup
Default IP Address
The Epic 5’s default IP address is 192.168.0.1. This can be modified,
however, we recommend you retain the default IP address if possible
for hassle-free installation of other Luxul products.
nNOTE: In the event another device on your network shares the
192.168.0.1 address, you’ll need to reassign the device’s IP
address or remove it from the network.
Connecting a Client Device
Connect a client device to one of the router LAN ports or to a switch
that is connected to a router LAN port. The DHCP server on the router is
configured by default. If your client device is set to obtain an IP address
automatically, no further configuration is required and you’re ready to log in.
nNote: Visit http://luxul.com/ip-addressing to learn more about
changing your computer’s IP address and getting connected.
Logging In
To access the router web configuration, open your web browser and enter
the router’s default 192.168.0.1 IP address in the address field. Log in to the
router using the default user name and password:
Default IP: 192.168.0.1
Username: admin
Password: admin
Select the menu items on the left to view and/or modify the configuration.
For information on configuring the Epic 5 and routers in general, review
the Support Resources at luxul.com.
4Hardware Operation
The front panel of the router features Power, System and USB LEDs; and port
status indicators for each of the router’s Ethernet ports.
The rear panel of the router features seven RJ-45 Ethernet ports: Two dedicated
WAN ports and five dedicated LAN ports. Using the two dedicated WAN
ports, the router can be connected to two independent Internet connections
simultaneously.
The rear panel also features a power switch and socket, recessed Reset button,
and a switch for selecting front-panel LED colors (blue/green/o) to match
other equipment in an audio/video rack.
Plug a USB flash drive or hard drive into the USB 3.0 port and configure the
built-in file/DLNA server to serve files to LAN-connected client devices.
The Console port supports advanced command-line functionality, but requires
a special cable. Contact support if your application requires a command line.
nNote: The Console port is not an Ethernet port. A special cable is
required for use. Contact support for more information.
Front Panel
Back Panel
Reset Button
The Reset button (located on the rear panel) can be used to reset (reboot) the
router, restore the router to default settings, or restore the router to factory
default software version and settings.
XTo Reboot the Router: With the Epic 5 powered on and running, briefly
press and release the Reset button. The router will reboot. When the System
LED flashes like a heartbeat, the unit is ready.
cCAUTION: Do not hold the button for more than three seconds.
Doing so may erase all settings and restore factory defaults.
XTo Restore the Default Settings: With the router powered on and running,
press and hold the Reset button for 5 seconds, then release the button.
The router will restore its default configuration and reboot. The software
version will not change. When the System LED flashes like a heartbeat, the
unit is ready.
cCAUTION: Restoring default settings will remove any/all
custom configuration.
XTo Restore Factory Software: With the router powered o, press
and hold the Reset button, turn the router on, and continue holding the
Reset button until the System LED turns on. The device will completely
reflash itself back to the factory default software version and settings.
wWARNING: Restoring factory software will remove any/all
custom configuration and remove newer firmware.
LED Indicators
Indicator & State Description
POWER On / SYSTEM O
POWER On / SYSTEM On
POWER On / SYSTEM Blinking
POWER On / SYSTEM Heartbeat
POWER O / SYSTEM O
Epic 5 is powered on and booting.
Loading operating system.
OS loaded; finishing boot process.
Booting finished/operating normally.
Epic 5 not powered.
USB On
Blinking
A USB device is connected.
USB device activity.
WAN/
LAN
Front
Top Row On
Bottom Row On
Flashing
10/100 Mbps device connected.
1000 Mbps device connected.
Data packets are being transferred.
WAN/
LAN
Rear
Yellow On
Green On
Flashing
10/100 Mbps device connected.
1000 Mbps device connected.
Data packets are being transferred.
Fold Fold Fold
3Access and Setup
Default IP Address
The Epic 5’s default IP address is 192.168.0.1. This can be modified,
however, we recommend you retain the default IP address if possible
for hassle-free installation of other Luxul products.
nNOTE: In the event another device on your network shares the
192.168.0.1 address, you’ll need to reassign the device’s IP
address or remove it from the network.
Connecting a Client Device
Connect a client device to one of the router LAN ports or to a switch
that is connected to a router LAN port. The DHCP server on the router is
configured by default. If your client device is set to obtain an IP address
automatically, no further configuration is required and you’re ready to log in.
nNote: Visit http://luxul.com/ip-addressing to learn more about
changing your computer’s IP address and getting connected.
Logging In
To access the router web configuration, open your web browser and enter
the router’s default 192.168.0.1 IP address in the address field. Log in to the
router using the default user name and password:
Default IP: 192.168.0.1
Username: admin
Password: admin
Select the menu items on the left to view and/or modify the configuration.
For information on configuring the Epic 5 and routers in general, review
the Support Resources at luxul.com.
4Hardware Operation
The front panel of the router features Power, System and USB LEDs; and port
status indicators for each of the router’s Ethernet ports.
The rear panel of the router features seven RJ-45 Ethernet ports: Two dedicated
WAN ports and five dedicated LAN ports. Using the two dedicated WAN
ports, the router can be connected to two independent Internet connections
simultaneously.
The rear panel also features a power switch and socket, recessed Reset button,
and a switch for selecting front-panel LED colors (blue/green/o) to match
other equipment in an audio/video rack.
Plug a USB flash drive or hard drive into the USB 3.0 port and configure the
built-in file/DLNA server to serve files to LAN-connected client devices.
The Console port supports advanced command-line functionality, but requires
a special cable. Contact support if your application requires a command line.
nNote: The Console port is not an Ethernet port. A special cable is
required for use. Contact support for more information.
Front Panel
Back Panel
Reset Button
The Reset button (located on the rear panel) can be used to reset (reboot) the
router, restore the router to default settings, or restore the router to factory
default software version and settings.
XTo Reboot the Router: With the Epic 5 powered on and running, briefly
press and release the Reset button. The router will reboot. When the System
LED flashes like a heartbeat, the unit is ready.
cCAUTION: Do not hold the button for more than three seconds.
Doing so may erase all settings and restore factory defaults.
XTo Restore the Default Settings: With the router powered on and running,
press and hold the Reset button for 5 seconds, then release the button.
The router will restore its default configuration and reboot. The software
version will not change. When the System LED flashes like a heartbeat, the
unit is ready.
cCAUTION: Restoring default settings will remove any/all
custom configuration.
XTo Restore Factory Software: With the router powered o, press
and hold the Reset button, turn the router on, and continue holding the
Reset button until the System LED turns on. The device will completely
reflash itself back to the factory default software version and settings.
wWARNING: Restoring factory software will remove any/all
custom configuration and remove newer firmware.
LED Indicators
Indicator & State Description
POWER On / SYSTEM O
POWER On / SYSTEM On
POWER On / SYSTEM Blinking
POWER On / SYSTEM Heartbeat
POWER O / SYSTEM O
Epic 5 is powered on and booting.
Loading operating system.
OS loaded; finishing boot process.
Booting finished/operating normally.
Epic 5 not powered.
USB On
Blinking
A USB device is connected.
USB device activity.
WAN/
LAN
Front
Top Row On
Bottom Row On
Flashing
10/100 Mbps device connected.
1000 Mbps device connected.
Data packets are being transferred.
WAN/
LAN
Rear
Yellow On
Green On
Flashing
10/100 Mbps device connected.
1000 Mbps device connected.
Data packets are being transferred.
Fold Fold Fold
3Access and Setup
Default IP Address
The Epic 5’s default IP address is 192.168.0.1. This can be modified,
however, we recommend you retain the default IP address if possible
for hassle-free installation of other Luxul products.
nNOTE: In the event another device on your network shares the
192.168.0.1 address, you’ll need to reassign the device’s IP
address or remove it from the network.
Connecting a Client Device
Connect a client device to one of the router LAN ports or to a switch
that is connected to a router LAN port. The DHCP server on the router is
configured by default. If your client device is set to obtain an IP address
automatically, no further configuration is required and you’re ready to log in.
nNote: Visit http://luxul.com/ip-addressing to learn more about
changing your computer’s IP address and getting connected.
Logging In
To access the router web configuration, open your web browser and enter
the router’s default 192.168.0.1 IP address in the address field. Log in to the
router using the default user name and password:
Default IP: 192.168.0.1
Username: admin
Password: admin
Select the menu items on the left to view and/or modify the configuration.
For information on configuring the Epic 5 and routers in general, review
the Support Resources at luxul.com.
4Hardware Operation
The front panel of the router features Power, System and USB LEDs; and port
status indicators for each of the router’s Ethernet ports.
The rear panel of the router features seven RJ-45 Ethernet ports: Two dedicated
WAN ports and five dedicated LAN ports. Using the two dedicated WAN
ports, the router can be connected to two independent Internet connections
simultaneously.
The rear panel also features a power switch and socket, recessed Reset button,
and a switch for selecting front-panel LED colors (blue/green/o) to match
other equipment in an audio/video rack.
Plug a USB flash drive or hard drive into the USB 3.0 port and configure the
built-in file/DLNA server to serve files to LAN-connected client devices.
The Console port supports advanced command-line functionality, but requires
a special cable. Contact support if your application requires a command line.
nNote: The Console port is not an Ethernet port. A special cable is
required for use. Contact support for more information.
Front Panel
Back Panel
Reset Button
The Reset button (located on the rear panel) can be used to reset (reboot) the
router, restore the router to default settings, or restore the router to factory
default software version and settings.
XTo Reboot the Router: With the Epic 5 powered on and running, briefly
press and release the Reset button. The router will reboot. When the System
LED flashes like a heartbeat, the unit is ready.
cCAUTION: Do not hold the button for more than three seconds.
Doing so may erase all settings and restore factory defaults.
XTo Restore the Default Settings: With the router powered on and running,
press and hold the Reset button for 5 seconds, then release the button.
The router will restore its default configuration and reboot. The software
version will not change. When the System LED flashes like a heartbeat, the
unit is ready.
cCAUTION: Restoring default settings will remove any/all
custom configuration.
XTo Restore Factory Software: With the router powered o, press
and hold the Reset button, turn the router on, and continue holding the
Reset button until the System LED turns on. The device will completely
reflash itself back to the factory default software version and settings.
wWARNING: Restoring factory software will remove any/all
custom configuration and remove newer firmware.
LED Indicators
Indicator & State Description
POWER On / SYSTEM O
POWER On / SYSTEM On
POWER On / SYSTEM Blinking
POWER On / SYSTEM Heartbeat
POWER O / SYSTEM O
Epic 5 is powered on and booting.
Loading operating system.
OS loaded; finishing boot process.
Booting finished/operating normally.
Epic 5 not powered.
USB On
Blinking
A USB device is connected.
USB device activity.
WAN/
LAN
Front
Top Row On
Bottom Row On
Flashing
10/100 Mbps device connected.
1000 Mbps device connected.
Data packets are being transferred.
WAN/
LAN
Rear
Yellow On
Green On
Flashing
10/100 Mbps device connected.
1000 Mbps device connected.
Data packets are being transferred.
Fold Fold Fold
READ ME FIRST
QUICK INSTALL GUIDE
Epic 5
High-Performance Gigabit Router
ABR-5000
Includes:
High-Performance Gigabit Router
Rack Mount Kit
Rubber Feet
Power Cord
SETUP AND CONFIGURATION
1Physical Installation
The Epic 5 can be rack-mounted or used as a desktop router. Install the
router in a stable/safe place to avoid any possible damage. Make sure there is
adequate space around the router for ventilation and proper heat dissipation.
Avoid placement in direct sunlight. Do not place heavy articles on the router
and verify the ground connection of the outlet is functioning properly.
Desktop/Shelf Installation
For desktop/shelf installation, attach the four rubber feet to the corner
indentations on the bottom of the router, then place the router on
a solid, level platform.
Rack Installation
Use the included L brackets for convenient installation in a 19-inch server or AV
rack. As shown below, use four screws to attach the L-shaped brackets on both
sides of the router then mount it horizontally in the rack. Use your desired
hardware to ax the router supports to the rack.
Install Brackets for Rack-Mounting Attach Feet for Desktop Installation
2Connecting Ethernet and Power
Before you attempt to configure the router, test the Internet connection to
verify that it is functioning properly. Once Internet access is confirmed to
be working, follow the steps below for installation and configuration.
Connecting Ethernet
Luxul recommends at least Cat-5e unshielded twisted pair (CAT5e UTP)
cabling. To ensure best performance and stable data transmission at 1000
Mbps, use Category-6 unshielded twisted pair (CAT6 UTP).
1. Connect the WAN: Connect the Internet cable from a telco/ISP
modem/router to the dedicated WAN 1 port on the Epic 5.
2. Connect the LAN: Connect a cable from the dedicated LAN 1 port on
the Epic 5 to a switch, access point, or computer.
For best performance, and to maximize available ports, Luxul recommends
connecting all LAN devices to a Luxul switch, then connecting that switch
to the Epic 5 LAN port via a single Ethernet cable.
nNOTE: Connect all LAN devices to a Luxul switch, then connect that
switch to the router for best results.
Connecting Power
Use the included power cable to connect the router to a surge-protected
outlet. The AC input socket and power switch are on the rear panel. The
built-in power supply supports 100~240VAC at 50/60Hz.
Sales
801-822-5450
Technical Support
801-822-5450
LUX-QIG-ABR-5000-v7
Copyright and Trademark Notices
No part of this document may be modified or adapted in any way, for any purposes without permission in
writing from Luxul. The material in this document is subject to change without notice. Luxul reserves the
right to make changes to any product to improve reliability, function, or design. No license is granted, either
expressly or by implication or otherwise under any Luxul intellectual property rights. An implied license
only exists for equipment, circuits and subsystems contained in this or any Luxul product.
© Copyright 2016 Luxul. All rights reserved. The name Luxul, the Luxul logo, the Luxul logo mark and Simply
Connected are all trademarks and or registered trademarks of Luxul Wireless, Inc. All other trademarks and
registered trademarks are property of their respective holders.
This manual suits for next models
1
Table of contents
Other Luxul Network Router manuals
Luxul
Luxul Dual-Band AC3100 User manual
Luxul
Luxul XFS-1084P User manual
Luxul
Luxul Epic 3 User manual
Luxul
Luxul Epic 4 XBR-4500 User manual
Luxul
Luxul XVS-F5 User manual
Luxul
Luxul XBR-2300 User manual
Luxul
Luxul XMS-1024 User manual
Luxul
Luxul XGS-1024 User manual
Luxul
Luxul XBR-2300 User manual
Luxul
Luxul EPIC 4 User manual
Popular Network Router manuals by other brands
Linksys
Linksys BEFSX41 - Instant Broadband EtherFast Cable/DSL Firewall... Product data
NETGEAR
NETGEAR RT311 reference guide
Siemens
Siemens SCALANCE XB-200 operating instructions
TRENDnet
TRENDnet GREENnet TEW-639GR Quick installation guide
TP-Link
TP-Link Archer C7 AC1750 Quick installation guide
MitraStar
MitraStar Movistar GPT-2541GNAC user guide
