LYNE Pulse 30 User manual

WHEELSET
OWNERS MANUAL
FOR MORE INFO ABOUT THIS PRODUCT
AND OUR OTHER PRODUCTS VISIT:
WWW.LYNECOMPONENTS.COM
INTRODUCTION
The Lyne Pulse and Amp wheelsets are mountain bike specific
and have been designed around the needs of modern
mountain bikers. These wheelsets use lightweight yet wide
rim profiles coupled with triple butted spokes and lightweight
reliable hubs.
Our wheels are made in Taiwan and have been tested to ISO
4210 safety standards.
IMPORTANT NOTES
INTENDED USE
Your wheelset is one of the most crucial parts of your bicycle, if
misused the result could be serious injury or death. Please take
serious note of the following points:
Pulse 30
This wheelset is made for cross country (XC) and mara-
thon use. This includes gravel roads and moderately
technical single track. This may include moderately rocky
terrain and sandy conditions. If you are a heavier rider you
may want to consider the AMP series as your XC or
marathon choice.
Amp 30 V2
These wheelsets are made for Trail & Enduro use. This
includes gravel roads and technical single track terrain.
This may include rocky terrain with moderate jumps.
These wheelsets are not intended for downhill
riding/racing and should not be used for large jumps and
extremely rough conditions at high speed.
WEIGHT LIMITATIONS
Pulse 30:
Rider weight under 100 kg
Amp 30 V2:
Rider weight under 120 kg
MAXIMUM INFLATION
Do not over inflate your wheels, this could seriously
damage your rims and could cause severe wheelset
failure which may lead to injury or even death.
Pulse 30: 29” Maximum Pressure: 3.2 bar/46 psi
AMP 30 V2: 29” Maximum Pressure: 3.2 bar/46 psi
WARNING
These wheelsets should be used in accordance with our
intended use section below, they are not for downhill riding
or racing, users will take full responsibility for the conse-
quences if this is not followed.
Please check our weight limitations below and do not
exceed these.
Please ensure that these wheels are compatible with other
parts of the bike before installation.
Do not continue riding if wheels are damaged.
Do not attempt to modify the wheels in any way, users will
take full responsibility for the consequences if this is not
followed.
Do not use metal tyre levers or screwdrivers to install the
tyre, this could damage the rim and rim tape.
Do not over inflate your wheels, this could seriously
damage your rims and could cause severe wheelset failure.
Use compressor pumps with caution, over inflation can
occur very quickly causing rim damage.
Ensure to deflate tyres when travelling on aeroplanes to
avoid damage due to pressure fluctuations.
Maintain your wheelsets regularly as described under
Maintenance below.

WARRANTY
CONTACT INFO
MAINTENANCE
This wheelset is warranted for a period of 1 year from the
date of purchase against any physical failure or breakage
from fatigue or poor workmanship. Wear and tear items
are not warranted; these items should be replaced during
servicing.
The warranty is expressly limited to the repair or replace-
ment of the defective part at Lyne Components’ option
and is the sole remedy of the warranty.
The warranty applies only to the original owner and is not
transferable. Proof of purchase is required to validate
warranty eligibility.
The warranty does not cover normal wear and tear,
routine maintenance, improper installation or improper
use of the wheelset, please refer to the ‘Intended Use’
section if unclear about this.
Modification of the wheelset in any manner will void the
warranty. Lyne Components will not be responsible for
incidental or individual costs incurred that are not covered
by this warranty.
The user assumes the risk of any personal injury or
property damage, including damage to the wheelset and
any other losses.
Routine maintenance will increase the lifespan of the
wheelset. Before and after every ride the wheelset should
be cleaned. Do not use high pressure washers for
cleaning, this will remove the grease from the hubs and
cause damage. Ensure that all mud and debris has been
removed during washing so that nothing gets in the way
of the wheelset during operation. Check your wheels for
damage before and after every ride. Check your wheels
for loose spokes before and after every ride. If spokes are
loose, do not simply tighten them, take your wheel to a
qualified mechanic for spoke tensioning. Tensioning
spokes unequally could damage your wheels. Do not
attempt any maintenance on your wheels unless you are a
skilled and experienced mechanic.
RIM PROFILES
Join: Welded
Spoke: 28H
Finish: Sandblast
Anodised
Weight: 495g(29”)
ETRTO: 622mm(29”)
ERD: 604mm(29”)
Material: Alloy 6066
Tyre Size: 2,0 - 2,3”
Join: Pin
Spoke: 32H
Finish: Sandblast
Anodised
Weight: 525g(29”)
ETRTO: 622mm(29”)
ERD: 594,5mm(29”)
Material: Alloy 6069
Tyre Size: 2,25 - 2,5
For any queries please feel free to contact us:
Email: [email protected]
URL: www.lynecomponents.com
Phone: [phone]
Address: Unit 4 Woodland House, 17 Woodlands Road,
Woodstock, Cape Town, South Africa 7925
30
35
19
30
35
18
AMP 30 V2
Pulse 30