Lynx Skylanders Swap Force User manual

(1) Return Box
Required Tools:
• Screwdriver (Included)
• Torx wrench (Included)
Estimated time for
completion:
25 min
Skylanders Swap Force Diorama Refresh Instructions - AC Version
004-517
(1) Header Logo
|DESIGN
>
MANUFACTURE
>
SUPPORT |
(2) Side Logo Panels (3) Front Graphic Panels (8) Swap Force Toys
(1) Return Shipping Label
(1) Torx Wrench
(1) Firmware
Update
CONTENTS
(1) Screwdriver (1) Graphic Removal Pick
(1) New SD
Content Card
(1) New Portal
Completed Swap Force
refreshed diorama.
Scope of work:
• Replace all graphic panels.
• Replace 3 logo panels with the new
Skylanders Swap Force logo panels.
• Replace existing portal with the new
Skylanders Swap Force portal
• Install firmware update .
• Install new SD content card.
• Replace all toys with the new
Skylanders Swap Force toys.
• Re-Install the Skylanders Diorama
and test for correct functionality.
• Place old all old parts in the return
box and apply the pre-paid label
provided in this kit.
Who to call:
For display troubleshooting, parts, or
service, please contact Lynx Innovation
Phone: [phone]
Normal business hours 8:00am - 6:00pm (PST)
Email: [email protected]
Normal response time within 24 hours

• Twist each character counter-clock wise then pull to remove (Place
in recovery box).
• Reverse these steps to install the new toys (see pg. 4 for toy layout).
• Light Core toys: Hold the bottom of the PCB (light plug) down
securely from under the diorama while installing toy.
Remove old toys and install new toys.
DIORAMA REFRESH INSTRUCTIONS - AC Version
5
- Re-attach the acrylic cover.
- Plug the AC cord into the diorama and perform functionality test
(see pg. 4), BEFORE reattaching the unit back onto the store xture.
IMPORTANT: Place old all old parts in the return box with
pre-paid label provided in this kit. Leave in the area within
the store where UPS picks up.
!
Remove diorama from store xture.
• Shelf = Remove 4 thumb screws that secure the Diorama to shelf.
• Towel Bar = Lift diorama off of towel bar.
1
• Remove the 13 screws holding the back panel in.
• Remove the three screws that hold the header graphic in place (Place in
recovery box).
• Remove header logo, and insert new Skylanders Swap Force header logo.
• Reverse these steps to install the new header logo.
Replace the header logo.
6
• Disconnect the speakers by unplugging the red wire. Do the same for
both sides (Place in recovery box).
• Remove the 4 screws to release the side panels.
• Pull off the side panels and remove the 4 screws holding in the speaker.
• Re-install the speaker to the new side panels included in the kit.
• Use the new screws provided in the kit and re-connect speaker wire.
• Pay attention of the orientation of the speaker before re-installing them
to the new side panels.
Replace the (2) side logo panels.
7
• Use the included graphic removal pick to remove the existing panels.
• Replace with the (3) new panels from the refresh kit and reinstall all 3
plastic covers.
Replace the (3) front graphic panels .
8
Remove main acrylic cover.
• Remove the two small blocks that lock the acrylic cover in place,
using the Torx wrench tool provided.
2
Install rmware update & new SD content card.
• Unplug power cord from back side of the diorama.
• Press to release the existing SD content card (Place in recovery box).
• Insert rmware update card from the installation kit.
• Plug the power cord back in on the back side of the diorama.
• You may need to press the “trailer button” to start the le transfer.
• Let the system copy the les. DO NOT Unplug from power or remove
rmware update card while the les are copying.
• Once the countdown to reboot starts at the bottom of the screen YOU MUST
unplug power source immediately.
• Remove the rmware update card.
• Install the new SD content card from the installation kit.
4
7
Unplug
Back Panel
1
2
6
5
4
3
Remove old portal and install new portal.
• Lay the diorama on its back and unplug the cord connecting the portal.
• Remove (4) screws to release the portal from the diorama (Place in
recovery box).
• Reverse these steps to install the NEW portal from the installation kit.
3
2 3
8

(1) Firmware SD
Update Cards
(1) Giants SD
Content Card
Need further assistance?
Phone: [phone]
Normal business hours 8:00am - 6:00pm (PST)
Email: [email protected]
Normal response time within 24 hours
FUNCTIONALITY TEST
Verify video is playing/looping on LCD monitor.
1
Press any of the character buttons.
4
Verify portal is illuminated.
2
Verify character positions are illuminated.
3
Press the “TRAILER” button
The “Overview Trailer” will play once with audio then return to
the “Overview Trailer” continuously looping with no audio.
5
The character video will play once followed by the “Video
Trailer” playing once then returning to continuously looping
with no audio.
Star Strike
(Light Core)
Flash Wing
(Light Core)
Blast Zone Blast Buckler
Wash Buckler
Bumble Blast
Roller Brawl
Countdown
TOY LAYOUT DIAGRAM
4
There is no video playing or no power.
1
• Conrm the power leads of the battery pack or AC plug are properly seated to the distribution board underneath the display.
System is powered on, but no video plays when a button is pressed.
2
• Conrm that the monitor ashes the Skylander Swap Force screen when the system boots up. Unplug and plug-in the power cord again for the system to reboot.
• Then verify the SD card is properly seated remove the acrylic cover ( be careful not to hit any of the characters). Press-in the SD card to release it, then
press the SD card back-in rmly. Then press a button at the front of the display and conrm the content is playing.
TROUBLESHOOTING GUIDE
If system is powered on and there is no change in the video content when a button is pressed, contact support.
1
5
3
2
4
RECOVERY ITEMS
Make sure you place the following items from the refresh
installation i n the return box with pre-paid label provided in
this kit. Leave in the area within the store where UPS picks up.
(1) Giants
Header Logo
(2) Giants Side
Logo Panels
(1) Old Giants
Portal
(8) Giants Toys
Recovery Box Recovery Label
+