M-Spa ELITE Series User manual

MSpa®ELITE
Owner’s Manual
E-BA049 BAIKAL
E-RE049 RÊVE
E-BL069 BLISS
EN
DO NOT RETURN MERCHANDISE TO YOUR DEALER STORE DIRECTLY. CALL MSPA AFTER
SALES SERVICE CENTER FOR ANY PRODUCT-RELATED QUESTIONS OR CONTACT MSPA AT
[email protected]
Due to MSpa continuous product improvement, MSpa reserves the right to change the
product appearance and specifications, which may result in updates to the instruction
manual without notice.
Where Luxury Is Affordable
www.the-mspa.com

ENTER THE WORLD OF MSPA
Thank you for choosing MSpa and for your confidence in our brand. We believe that you will enjoy many
benefits of using MSpa products for years to come.
To guide you in your initial MSpa experience, we are pleased to present you with this instruction manual.
Please read this manual carefully before using the product for the first time.
We are delighted to welcome you to the MSpa family, and we are looking forward to sharing with you the full
spectrum of our expertise.
Enjoy your MSpa!
Scan the QR code to enter the MSpa official website
CONTENT
Safety precautions………………………………………………………………......................................................
Specifications and product overview………………………………………………..............………........................
First use preparation and set-up………………………………………………….........................……………........
Spa set-up……………………………………............................…………………………......….............................
Wired controller operation………………………………………........................…................................................
Water maintenance and chemicals………………….......................................………..………………..…...........
Drainage, cleaning and storage………………………...................................………………..………..……..........
Disposal and environmental protection…………………………....................................…..................................
Troubleshooting…………………………………………….......……………………….…...…...…..........................
MSpa limited warranty policy …………………………............………................................………………...........
3
9
10
13
17
19
21
23
23
26
Welcome,
2

3
SAFETY PRECAUTIONS
For your own safety and that of your product, make sure to follow the safety
precautions below. Failure to follow the instruction may result in serious injury,
property damage, or death. Improper installation or operation will void the warranty.
READ, UNDERSTAND AND FOLLOW ALL INSTRUCTIONS
KEEP THE MANUAL FOR FUTURE REFERENCE
! DANGER
ƔRisk of Accidental Drowning. Extreme caution must be exercised to prevent
unauthorized access by children.
ƔRisk of drowning. Inspect the spa cover regularly for leak, premature wear, and
tear, damage or signs of deterioration. Never use a worn or damaged cover as it
will not provide the level of protection required to prevent unsupervised access
to the spa by a child.
ƔRisk of drowning. Always lock the spa cover after each use.
ƔRisk of injury. If the supply cord is damaged, it must be replaced by the
manufacturer, service agent or similarly qualified persons to avoid a hazard.
ƔRisk of Electric Shock. Do not permit any electrical appliances, such as a light,
telephone, radio or television within 1.5m (5 feet) of a spa tub.
ƔRisk of Electric Shock. Do not use the spa when it is raining, thundering, or
lightning.
ƔTo reduce the risk of electric shock, do not use an extension cord, timers, plug
adaptors or conversion plugs to connect the unit to electric supply. Provide a
properly located outlet.
ƔTransportable whirlpool baths and swimming pools with incorporated heating
elements must be connected to a grounded mains supply socket and a supply
cord fitted with a plug and PRCD equipped with a tripping current of 10mA.
! WARNING

4
Ɣ&RPSRQHQWVFRQWDLQLQJPRYLQJSDUWVH[FHSWSDUWVVXSSOLHGZLWKVDIHW\
extra-low voltage not exceeding 12V, must be inaccessible to occupants in the
spa.
Ɣ3DUWVLQFRUSRUDWLQJHOHFWULFDOFRPSRQHQWVH[FHSWUHPRWHFRQWUROGHYLFHVPXVW
be located or fixed, so that they cannot fall into the spa.
Ɣ(OHFWULFLQVWDOODWLRQVKRXOGIXOILOOWKHORFDOUHTXLUHPHQWRUVWDQGDUGV
Ɣ7KHZLUHGFRQWUROOHUVKDOOEHSURSHUO\VWRUHGDWWKHVLGHSRFNHWZKHQQRWXVHG
to protect the controller from falling or from other factors.
Ɣ7KLVDSSOLDQFHFDQEHXVHGE\FKLOGUHQDJHGIURP\HDUVDQGDERYHDQG
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance. Cleaning and user
maintenance shall not be performed by children without supervision.
Ɣ7RUHGXFHWKHULVNRULQMXU\NHHSFKLOGUHQDZD\IURPWKLVSURGXFWXQOHVVWKH\
are closely supervised at all times.
Ɣ7RUHGXFHWKHULVNRIFKLOGGURZQLQJVXSHUYLVHFKLOGUHQDOOWLPHV$WWDFKDQG
lock the spa cover after each use.
Ɣ0DNHVXUHWKHIORRULVFDSDEOHRIVXSSRUWLQJWKHH[SHFWHGORDGZKLFK\RXFDQ
find from the spec sheet. Calculate the expected load of water capacity plus the
total weight.
Ɣ$GHTXDWHGUDLQLQJV\VWHPPXVWEHSURYLGHGDURXQGWKHVSDWRGHDOZLWK
overflowing water.
Ɣ7RUHGXFHWKHULVNRILQMXU\
a) Lower water temperatures are recommended for young children and when
spa is used for more than 10 minutes. In order to avoid the possibility of
hyperthermia (heat stress) occurring it is recommended that the average
temperature of spa-pool water should not exceed 40°C (104°F).
b) Since excessive water temperature has a high potential for causing fetal
damage during the early months of pregnancy, pregnant or possibly pregnant
ZRPHQVKRXOGOLPLWVSDZDWHUWHPSHUDWXUHWR&)
c) Before entering a spa or hot tub the user should measure the water
temperature with an accurate thermometer since the tolerance of water
temperature-regulating devices varies.

d) The use of alcohol, drugs, or medications before or during spa use may lead
to unconsciousness with the possibility of drowning.
e) The use of alcohol, drugs, or medications can greatly increase the risk of fatal
hyperthermia in spas.
I7KHFDXVHVDQGV\PSWRPVRIK\SHUWKHUPLDPD\EHGHVFULEHGDVIROORZV
Hyperthermia occurs when the internal temperature of body reaches a level
VHYHUDOGHJUHHVDERYHWKHQRUPDOERG\WHPSHUDWXUH&)7KH
symptoms of hyperthermia include an increase in the internal temperature of
body, dizziness, lethargy, drowsiness, and fainting. The effect of hyperemia
includes failure to perceive heat; failure to recognize the need to exit spa;
unawareness of impending hazard; fetal damage in pregnant women;
physical inability to exit the spa; and unconsciousness resulting in the danger
of drowning.
g) Obese persons or persons with a history of heart disease, low or high blood
pressure, circulatory system problem, or diabetes should consult a physician
before using a spa.
h) Persons using medications should consult a physician before using a spa
since some medications may induce drowsiness while other medication may
affect heart rate, blood pressure, and circulation.
i) Check with doctor before use if pregnant, diabetic, in poor health, or under
medical care.
Ɣ3HRSOHZLWKLQIHFWLRXVGLVHDVHVKRXOGQRWXVHDVSDRUDKRWWXE
Ɣ7RDYRLGLQMXU\H[HUFLVHFDUHZKHQHQWHULQJRUH[LVWLQJWKHVSDWKHRUKRWWXE
Ɣ:DWHUWHPSHUDWXUHLQH[FHVVRI&)PD\EHLQMXULRXVWR\RXUKHDOWK
Ɣ1HYHUXVHDVSDRUKRWWXEDORQHRUDOORZRWKHUVWRXVHWKHVSDDORQH
Ɣ'RQRWXVHDVSDRUKRWWXELPPHGLDWHO\IROORZLQJDVWUHQXRXVH[HUFLVH
Ɣ6SDKHDWLQFRQMXQFWLRQZLWKDOFRKROGUXJVRUPHGLFDWLRQFDQFDXVH
unconsciousness.
Ɣ([LWLPPHGLDWHO\LIXQFRPIRUWDEOHGL]]\RUVOHHS\6SDKHDWFDQFDXVH
hyperthermia and unconsciousness. Do not put the spa under 0°C (32°F)
environment in order to avoid freezing if there is still water in the pool. It is
helpful to put a temp barrier mat in between the spa pool and the ground. Similar
mat, which is made of foam material, or other materials with heat barrier function
can also be used. Do not turn on the spa when the water is frozen.
5

6
Ɣ1HYHUSRXUZDWHUZLWKDWHPSHUDWXUHKLJKHUWKDQ&)GLUHFWO\LQWRWKH
spa.
Ɣ$OZD\VXQSOXJWKLVSURGXFWIURPWKHHOHFWULFDORXWOHWEHIRUHUHPRYLQJFOHDQLQJ
servicing, or making any adjustment to the product.
Ɣ1HYHUMXPSRUGLYHLQWRDVSDRUDQ\VKDOORZERG\RIZDWHU
Ɣ1RSDUWRIWKHHOHFWULFDSSOLDQFHLVWREHORFDWHGDERYHWKHEDWKGXULQJXVH
Ɣ'RQRWEXU\WKHHOHFWULFDOFRUG/RFDWHWKHFRUGZKHUHLWZLOOQRWEHGDPDJHGE\
lawn mowers, hedge trimmers, and other equipment.
Ɣ'RQRWDWWHPSWWRSOXJLQRUXQSOXJWKLVSURGXFWZKLOHVWDQGLQJLQZDWHURUZKHQ
your hands are wet.
Ɣ'RQRWXVHWKHVSDLIGDPDJHGGXULQJWKHGHOLYHU\DQGRUPDOIXQFWLRQLQJLQDQ\
way. Contact MSpa service center for further direction.
Ɣ.HHSDOOSHWVDZD\IURPWKHVSDWRDYRLGDQ\GDPDJH
Ɣ'RQRWDGGEDWKRLORUEDWKVDOWVWRWKHVSDZDWHU
Ɣ$OZD\VDGGFKHPLFDOVWRZDWHUQHYHUDGGZDWHUWRFKHPLFDOV$GGLQJZDWHUWR
chemicals may cause strong fumes or violent reactions and hazardous chemical
spray.
Ɣ)RUZDWHUDOUHDG\XVHGGLVFKDUJHLWLQWLPHRUXVHZDWHUFKHPLFDOVIRUFOHDQLQJ
Usually, it is recommended to drain and refill the spa with clean water every 3-5
days.
Ɣ8VH0VSDFKHPLFDONLWIRUGLVLQIHFWLRQLQDFFRUGDQFHZLWKPDQXIDFWXUHU¶V
instructions.
Ɣ'RQRWOHDYHRUVHWXSWKHVSDLQWHPSHUDWXUHORZHUWKDQ&)LIKHDWHULV
not operating.
Ɣ$OZD\VHQWHUDQGH[LWWKHVSDRUKRWWXEVORZO\DQGFDXWLRXVO\&DXWLRQRIZHW
floor.
Ɣ7RDYRLGGDPDJHWRWKHSXPSQHYHUWXUQRQWKHVSDRUKRWWXEVXQOHVVLWLV
filled with water to the minimum water line.
Ɣ3ODFHWKHVSDRUWKHKRWWXERQO\RQDSURSHUO\SUHSDUHGVLWHWKDWFDQZLWKVWDQG
the floor loading requirement of the spa.
! CAUTION

7
Ɣ'RQRWOHDYHWKHVSDHPSW\IRUH[WHQGHGSHULRGRIWLPH'UDLQZDWHULQVLGHWKH
pool thoroughly if it is not used for a long period of time. Do not expose the spa
to direct sunshine. Check regularly before each use. Put away the spa or fence
it up in time after using.
Ɣ2SHQWKHVSDWRSOLGZKHQWKH%XEEOHIXQFWLRQLVRQ
Ɣ,QRUGHUWRDYRLGDKD]DUGGXHWRLQDGYHUWHQWUHVHWWLQJRIWKHWKHUPDOFXWRXW
this appliance must not be supplied through an external switching device, such
as a timer, or connected to a circuit that is regularly switched on and off by the
utility.
Ɣ5HIHUWRUHOHYDQWFKDSWHUIRUGHWDLOVFRQFHUQLQJFOHDQLQJDQGRWKHU
maintenance.

8
Zone 2 Zone 2
h
h
Zone 1
Zone 0
Zone 0
2.5 m
2.5 m
1.5 m 1.5 m2.0 m 2.0 m
Warning: The water protection levels of appliance at different product zones are
different. See the following diagram. ( Installation regulations comply to IEC
60364-7-702)
NOTE-The measured zone dimensions are limited by walls and fixed partitions.
Zones
Zone 0
Zone 1
Zone 2
Description of the zones
Zone 0 is the interion of the basin including any recesses in their
walls or floors.
Zone 1 is limited by
Zone 0
A vertical plane 2m from the rim of the basin.
The floor or the surface expected to be occupied by persons
The horizontal plane 2.5m above the floor or the surface
Zone 2 is limited by
A vertical plane external to zone 1 and parallel plane 1.5m
from the former.
By the floor or surface intended to be occupied by persons.

9
SPECIFICATIONS
JET & BUBBLE SPA
E-BA049 / Baikal
E-RE049 / Rêve
E-BL069 / Bliss
Round
Round
Square
4
4
4 + 2
700Ltr.
*DO
700Ltr.
*DO
930Ltr.
*DO
ijP
(71”)
ijP
(71”)
[P
(73”)
1.40m
(55”)
1.40m
(55”)
1.45 x 1.45m
(57”)
0.70m
´
0.70m
´
P
(27”)
36kg
(79.4lbs)
36kg
(79.4lbs)
42kg
(92.6lbs)
Model No.
/ Code Shape Seating Capacity Water Capacity Outside Dimensions Inside Dimensions Height Weight
Control System
Total Power
Heater
Massage Air Blower
Filter Pump
Integrated Ozone Generator
Top Lid
Spa Material
Spa Liner Material
Control System Specs E-BA049 / E-RE049 / E-BL069
$&9+]
2300W
1500W
9:(%$(5(:(%/
(E-BA049 / E-RE049: 75W x 2sets, jet pressure: above 0.5 bar, 4 high efficiency hydro-jets)
(E-BL069: 75W x 3sets, jet pressure: above 0.5 bar, 6 high efficiency hydro-jets)
:OHYHOV/:/:/:
9:
:0J+U
Rhino-Tech™ reinforced PVC
Premium Rhino-Tech™ reinforced PVC
with Micro Mspassima Fabric
Premium PVC material
Jet

10
PRODUCT OVERVIEW
Content of the package
NOTE: Drawings for illustration purpose only. The actual product may vary. Not to scale.
A. B. C.
D.
H.
N.
I. J. .
E. F. *
®
®
®
* round or square
* E-BL069 is a square shape spa
* Buckle spa cover and ground mat for E-BL069
®
L.
JET

11
REF. NO. PARTS DESCRIPTION QTY.
Spa cover with aluminum foil inside
Spa tub
Wired controller
+HDWSUHVHUYDWLRQEXEEOHPDW)RU(5(%$
Digital lock (except for E-BL069)
Inflation hose
Filter cartridge set (twin pack)
Inflatable bladder
Spa drain valve adaptor
Wrench
Repair kit
Buckle spa cover and ground mat set
Instruction DVD
NOTE: When ordering parts, be sure to quote the model number and part numbers.
A
B
C
D
E
F
G
H
I
J
K
L
M
1
1
1
1
1
1
1
1
1
1
1
1
1
FIRST USE PREPARATION AND SET-UP
ƔThe spa can be installed indoors and outdoors. For household use only.
ƔThe spa must be set up on a flat, smooth, and firm surface that is capable of supporting the maximum load
of the filled spa with the listed number of maximum occupants.
ƔMake sure the area is free of sharp objects under or around the spa. Uneven of unsound surfaces can
damage the spa and void your warranty. Level the surface before filling the spa with water.
ƔProvide adequate drainage system around the spa to deal with overflowing water and splashes.
ƔMake sure there is enough clearance around the spa for full access to the spa equipment for maintenance
DQGRUVHUYLFH
Site preparation and requirements
Ɣ9HULI\WKHIORRUFDQVXSSRUWWKHILOOHGZHLJKWRIVSDZLWKWKHPD[LPXPQXPEHURIRFFXSDQWV&KHFNZLWKD
qualified contractor or structural engineer to verify the requirement.
Ɣ0DNHVXUHWKHIORRULVZDWHUUHVLVWDQWDQGSURYLGHVDQRQVOLSVXUIDFH'RQRWLQVWDOOWKHVSDRQDFDUSHWRI
any other material that could be damaged by the moisture.
Ɣ+XPLGLW\LVDQDWXUDOO\VLGHHIIHFWRILQGRRUVSDLQVWDOODWLRQ7KHURRPVKDOOEHSURSHUO\YHQWLODWHGWRDOORZ
moisture to escape. Install a ventilating system to prevent excess condensation moisture in the room.
Additional requirements for indoor installation

1. 2. 3.
12
Ɣ0DNHVXUHWRVHWXSWKHVSDRQDILUPOHYHODQGVPRRWKVXUIDFHWKDWLVVWURQJHQRXJKWRVXSSRUWWKHIXOO
weight of the filled spa and the number of maximum occupants.
Ɣ'RQRWVHWXSWKHVSDRQJUDVVRUGLUHFWO\RQWKHJURXQGDVWKLVLQFUHDVHVWKHDPRXQWRIGHEULVHQWHULQJWKH
spa and can damage the spa floor.
Ɣ'RQRWOHDYHWKHVSDWXEH[SRVHGWRGLUHFWVXQOLJKWIRUDQH[WHQGHGSHULRGRIWLPH
Ɣ,WLVWKHSRVVLEOHWRLQVWDOODQGOHDYHWKHVSDRXWVLGHDWDWHPSHUDWXUHQRWORZHUWKDQ&)DQGWKH
water inside the circulation system, the pump, and the pipes is not frozen. Put a Heat Preservation Mat in
between the spa bottom and the ground to prevent heat loss from the bottom of the spa and to provide
better heat retention.
Additional requirements for outdoor installation
Spa Control Unit Connected to External Equipotential Bonding Conductors
A qualified electrician shall wire the spa control unit to the household equipotential terminal using a minimum
1.5mm² solid copper conductor.
1. Plug the machine into the mains.
2. Press the RESET button on the PRCD. The indicator turns red.
3. Press the TEST button on the PRCD. The red color shown on the indicator should disappear. Otherwise the
PRCD is faulty. Do not use the spa. Contact a qualified electrician to correct the fault.
4. Press the RESET button on the PRCD again. The indicator should turn red. If yes, the spa is ready for use.
PRCD Testing
5LVNRIHOHFWULFVKRFN7KLVSURGXFWLVSURYLGHGZLWKD35&'ORFDWHGDWWKHHQGRIWKHSRZHUFRUG7KH
PRCD must be tested before each use. Do not use the spa if the PRCD does not function properly.
Disconnect the power cord until the fault has been identified and corrected. Contact a licensed electrician to
correct the fault. There are no serviceable parts inside the PRCD. Opening the PRCD will void the warranty.
! WARNING
RESET
TEST
RESET
Indicator TEST
RESET
TEST

JET
31
13
SPA SET-UP
1. Move the entire package to the selected site. Open the carton carefully as it can be used to store the spa
during long term storage or when not in use.
2. Lay out all the parts on the ground and make sure all parts are accounted for. Make sure the spa tub is right
side up. (*For missing or damaged part, contact the MSpa Service Center)
6SUHDGWKH+HDW3UHVHUYDWLRQ*URXQG0DWRYHUDFOHDUHGDUHD6SUHDGRXWWKHVSDOLQHURYHUWKHJURXQG
mat. The heat Preservation Mat prevents heat loss from the bottom of the unit.
2
NOTE:
Bliss E-BL069: Spread out
the square ground mat and
place it to the selected site.
Make sure the buckle of
cover and mat is attached
when the spa is not in use.
Ɣ
this side
face down
Spa Inflation
4.1 Plug the spa into the grounded supply socket.
4.2 Press the RESET button on the PRCD, the screen on controller shows numbers.
4.3 Turn the inflation knob to the inflation status <ON> and long press the bubble button on the controller
to start inflating until the yellow section of the manometer is pushed out.
4.4 Stop pressing the bubble button and turn the knob back to <OFF> .
4.
4.3 4.4
Yellow
ON OFF
BUBBLE

5
14
Spa Bladder Inflation.
5.1 Open the air valve (a) on the bladder. Insert the inflation
hose (b) into the valve. Open the air valve (C) on the spa
pool. Make sure you choose the correct one in black color.
5.2 Press the Bubble button to inflate until the bladder
is firm to touch but not hard.
5.3 Press Bubble button for more than 3 seconds to
turn off the function. Disconnect the inflation hose from the
air blower outlet and the valve.
5.4 Replace the air valve cap (c) back. Close and recess the
inflation valve (a).
5.
(a)
(b)
(c)
Note:
Before inflation, check whether the manometer cap is screwed up tight on the valve of pool
body. If not, please tighten and then inflate. After inflation, the manometer cannot be removed,
otherwise the air will be released.
When the Yellow section is pushed out, the Spa inflation is completed. You can fill the Spa with water.
After water filling is completed, check the air pressure once again to ensure the manometer reaches its
Green section. Always ensure the manometer is in the Green section during use.
If the White section of the manometer appears, the spa is over inflated. Rotate the valve cap counter
clockwise, have the air released till the Green section is pushed out, then tighten it clockwise.
To avoid over inflation caused by warm weather or sunshine when leaving spa for weeks inflated and
ILOOHGZLWKZDWHULQWHPSHUDWXUHKLJKHUWKDQ&)SOHDVHUHOHDVHVRPHDLUWRPDNHVXUHWKH
manometer is always on in the Yellow section.
Green
Yellow
White
BUBBLE
BUBBLE
NOTE: Deflation Instruction
Spa Deflation
1. Unscrew the air valve cap on the spa pool to deflate the spa.
2. Once the deflation is completed, place the cap back.
Spa Bladder Deflation
1. Pull the valve cap out and squeeze the valve at its base until deflated.
2. Close and recess the valve back.

6.4
6
15
ƔThe water level must reach the Minimum water line but not exceed the Maximum line to avoid
pump failure.
ƔNever pour water with a temperature higher than 40°C (104°F) directly into the spa.
ƔTo avoid control system failure, do not operate the spa until water reaches the Minimum
line.
Water Filling
6.1 Check the spa mark is at the selected area and point
the drain valve toward a suitable draining area
before inflation.
6.2 Fill the spa tub with fresh water to a level between
Minimum and Maximum line marked on the inside
of the spa wall. Do not over fill the spa. It is recommended to fill the spa with lukewarm water for quick
heating and energy saving.
WARNING:
6.3 After water filling, double check the spa pool air pressure to make sure the manometer points out the
*UHHQVHFWLRQ
6.4 Place the inflated air bladder and the zipper spa cover over the spa tub. Make sure the spa cover is
zipped and locked by the digital lock in the accessory pack.
IMPORTANT:
Ɣ,QVSHFWWKHVSDSUHVVXUHUHJXODUO\IRUOHDNSUHPDWXUHZHDURUGHWHULRUDWLRQ
Ɣ&KHFNDQGZD[WKH]LSSHUUHJXODUO\WRPDNHLWVPRRWKIRURSHUDWLRQDQGWRDYRLGVSOLWV
6.
6.5 Turn on the Heater on the spa wired controller, refer to the “Wired Controller Operation” section.
0D[LPXPKHDWLQJWHPSHUDWXUHLV&)+RXUO\KHDWLQJUDWHLVDERXW&&))
IRUSHUVRQVDQG&&))IRUSHUVRQV
Zipper and Buckle Operation
7.1 Digital Lock Operation
The default password is “000”)ROORZWKHVWHSVEHORZWRFKDQJHWKHSDVVZRUG
Ɣ3XVKWKHEXWWRQDLQWKHGLUHFWLRQRI)LJWRXQORFNWKHGLJLWDOORFN
Ɣ6HW\RXUSUHIHUUHGSDVVZRUGLQGLJLWVE\WXUQLQJWKHQXPEHUZKHHOEVHH)LJ
Ɣ,QVHUWEDFNWKHFDEOHF7KHQHZSDVVZRUGLVVHW
7.

7.1.(1) 7.1.(2) 7.1.(3)
16
®
(b)
®
(a)
®
(c)
7.2 Square Spa Buckle Lock Operation
Lock the Buckle
Ɣ,QVHUWWKHEXFNOHRQWKH*URXQG
Mat into the Spa cover buckle, until
you hear a “Click” sound.
Unlock the Buckle
Ɣ3LQFKERWKVLGHVRIWKHORFNHGEXFNOHDQGSUHVVGRZQWKHURXQGGRWLQFHQWHULQWKHVDPHWLPH
Press down the center button and release the lock.
Lock Unlock
7.2

(a) (a)
(
a
)
(5((%$MHWV E-BL069 - 6 jets
JET Button Operation
$GMXVWWKHMHWQR]]OHVDLQWKHSURSHUGLUHFWLRQIRU\RXUQHHGV
7XUQWKHMHWFRQWURONQREEFORFNZLVHRUDQWLFORFNZLVHWRFKDQJHWKHZDWHUVWUHDPSRZHU7KH
maximum power combo is air and hydro-jet together. The minimum power is hydro-jet on only. There
DUHWZRMHWFRQWURONQREVIRU(5(%$DQGWKUHHMHWFRQWURONQREVIRU(%/
(b)
Control knobs open or close.
c
l
o
s
e
o
p
e
n


17
WIRED CONTROLLER OPERATION
Heater Button: Press HEATER button to start or stop heating.
The filter will automatically be running for 15 seconds to test the working condition once the HEATER
function is started. If there is no abnormality, the heater will keep working until the water temperature
reaches the set value. When the water temp goes below the set temp, the heater will restart to heat
the water automatically. The HEATER button displaying red means that the heating system is
activated. The HEATER button displaying green means that the system is at rest and keeping the
water at the set temp.
Filter Button: 3UHVV),/7(5EXWWRQWRWXUQWKHIXQFWLRQRQRII7KHOLJKWRI),/7(5EXWWRQGLVSOD\V
green when activated.
NOTE: Filtration cannot be turned off when Heating is activated. When the Heating function is turned
off, filtration will be stopped after 30 seconds. Filtration function can then be activated separately.
NOTE: The auto-filtration system is automatically activated every 4 hours.
Bubble Button: Can adjust among 3 levels of bubbling power. The default bubbling massage
power is at level 2 (500W). Press the BUBBLE button again, switching to level 3 (720W). Press again
FILTER
HEATER
BUBBLE
JET
Heater Button
- Adjust the bubble level by pressing
WKHEXWWRQ/:/:/:
Bubble Button
Up Button
Filter Button
Timer Button
Down Button
Jet Button
&HOVLXV)DKUHQKHLW
Toggle Button Ozonator Button
JET
Temperature display: press RESET on PRCD, read the current temperature on the screen.
Jet Button: To activate the water jet massage function.
NOTE: The Bubble button can only be adjusted between L1 (300W) and L2 (500W) while the Jet
function is on. JET function will shut down automatically after one-hour continuous operation.

18
to enable level 1 (300W). To shut down the function, press the BUBBLE button for 3 seconds.
NOTE: The bubbling massage function will be shut down automatically after every 20 minutes
operation for safety concern. It cannot be operated within 10 minutes after shutting down.
Attention: The bubble function can only be activated when the inflation knob is in <OFF> position.
Adjustment Buttons: Press UP or DOWN button, the screen flashes setting temperature. Re-set
the temperature within 3 seconds. Otherwise the temperature setting mode will end automatically. If
the other button is pressed during the setting , the setting will also stop. The current temperature
shown on the screen is confirmed.
NOTE: 'HIDXOWVHWWLQJWHPSHUDWXUHLV&7HPSHUDWXUHVHWWLQJUDQJH&
Controller Locking: Press UP and DOWN button at the same time for 3 seconds, the buzzer will ring
3 times, meaning that the controller is locked. In this mode, the function will not be turned on if the
button is pressed. Press UP and DOWN button at the same time again for 3 seconds to unlock the
controller.
Timer Button: Press the TIMER button to enter the intelligent pre-setting mode. By press UP and
DOWN button, you can set and start heating automatically with in up to 99 hours. The TIMER setting
is confirmed if no further operation in more than 3 seconds or press TIMER button again. The heater
will start working after current setting hours. The setting hour can also be changed by entering the
pre-setting mode again. The light of TIMER button flashes green when activated.
Cancel: Press the TIMER button for 3 seconds to cancel the pre-setting.
NOTE: The pre-setting function cannot be turned on during heating process. The pre-setting mode
will also end once the heating function is on or after the spa is reboot.
Celsius/Fahrenheit Toggle Button: The temperature can be displayed in either Celsius or
Fahrenheit.
Ozonator Button: Activate the Ozone. The Ozone icon shows green when the Ozone function is
activated. For bathers' safety concern, the ozonator cannot be operated at the same time when the
Bubbling or Jet function is on. The Ozonator will be off automatically after operating for 2 hours. The
R]RQHRXWSXWLVPJ+U
NOTE: Please do not soak in the spa when the Ozone is on. The Ozonator will not work when the
spa has no water or when the Bubble Button is on.
UP
DOWN
TIMER
Filter Cartridge Cleaning Reminder: When the red light keeps flashing (Filter function is
OFF) or red and green lights are alternately flashing(Filter function is ON), the filter cartridge
shall be cleaned or replaced. After that, press Filter button for 3 seconds to clear the
reminder.
IMPORTANT: The following conditions will lead to slow water heating
Ɣ7KHDPELHQWWHPSHUDWXUHLVORZHUWKDQ&)
Ɣ2XWGRRUZLQGVSHHGLVDERYHPVPSK
Ɣ7KHDLUEXEEOHIXQFWLRQLVDFWLYDWHGZKHQKHDWHULVRQ
Ɣ7KHVSDLVQRWSURSHUO\FRYHUHGZLWKWKHVSDFRYHUZKHQWKHKHDWHULVRQ

19
LED READING CAUSE SOLUTION
E0
E1
Water temperature is lower than 0°C
degree or exceeds 55°C (131°F)
Temperature sensor failure
Water pressure switch failure
Filter failure
Water level is not at minimum water line
Contact the MSpa Service Center.
Add water above the minimum line.
Change the water or contact the MSpa
Service Center.
ERROR CODE CHART
WATER MAINTENANCE AND CHEMICALS
Water Sanitation
The spa owner must regularly check and keep the spa water sanitized and maintained regularly (daily, if
necessary). Adding sanitizer or other chemical will control bacteria and viruses present in the spa water. The
maintenance of a proper water balance through appropriate use of sanitizers is the most important factor in
maximizing the life and appearance of the spa, as well as ensuring clean, healthy, and safe water. Proper
technique is important for water testing and treating the spa water. See your spa professional for chemical,
sanitizer, test kit, and testing procedures questions.
CAUTION:
Ɣ$OZD\VIROORZWKHFKHPLFDOPDQXIDFWXUHU¶VGLUHFWLRQDQGWKHKHDOWKDQGKD]DUGZDUQLQJ
Ɣ'RQRWDGGFKHPLFDOVLIWKHVSDLVRFFXSLHG7KLVFDQFDXVHVNLQRUH\HLUULWDWLRQ
Ɣ&RQFHQWUDWHGFKORULQHVROXWLRQVFDQGDPDJHWKHVSDWXE,PSURSHUFKHPLFDOXVHZLOOYRLGWKHZDUUDQW\
Maintenance of Spa Water and Cartridge
Protect all the spa occupants from possible water related illness by keeping the spa water clean and sanitized.
$OZD\VSUDFWLFHJRRGK\JLHQH7RHQVXUHSURSHUVSDZDWHUTXDOLW\E\IROORZLQJWKHVHSURFHGXUHV
1. Inspect and clean the filter cartridge after each use, and change the filter cartridge after it works
continuously for 150 hours, or after seeing a cleaning reminder.
ƔUnscrew the cartridge assembly from the spa tub wall and remove the cartridge by turning it counter
clockwise (Fig.1.1)
ƔUse a garden hose to rinse off the cartridge. If the cartridge remains soiled and discolored, it should be
UHSODFHG.HHSVSDUHFDUWULGJHVRQKDQG)LJThere are two filter cartridges from the original
package. One is for use, the other is spare.
ƔReinstall the clean or spare cartridge back onto the spa tub wall but turning it on clockwise. (Fig.1.3)

20
1.1 1.2 1.3
2. Change the spa water every 3-5 days depends on the spa use. For instructions see “Cleaning, draining,
and storage”.
3. Use spa chemicals to maintain proper water chemical balance. Spa damage resulting from misuse of
chemicals and mismanagement of spa water is not covered by the warranty. Consult with your local spa or
pool retailer for more information on use of chemical products.
4. All occupants must shower before entering the spa.
Do not use skin care or sunscreen products while
using the spa.
5. When spa inlet or outlet is clogged with dirt, use the
Wrench to check the problem and clean the inlet or
outlet.
5
Water Balance
0DLQWDLQWKHVSDZDWHUS+OHYHOEHWZHHQDQGWKHWRWDODONDOLQLW\EHWZHHQDQGSSPDQGWKHIUHH
chlorine level between 3 to 5ppm. Use the *optional Test Strips to test the spa water chemistry before each use
of the spa and continue to test the water no less than once a week.
7KH7HVW6WULSVFDQWHVWWKH³)UHH&KORULQH´³S+´DQG³7RWDO$ONDOLQLW\´OHYHODWWKHVDPHWLPH
1. Dip the entire strip into the water and remove immediately
2. Hold the strip level for 15 seconds. Do not shake excess water from the strip
3. Compare the strip pad to the color chart on the packaging label. If necessary, adjust the chemical level in
the pool water.
NOTE:
Ɣ/RZS+ZLOOGDPDJHWKHVSDWXEDQGWKHSXPS'DPDJHUHVXOWLQJIURPWKHFKHPLFDOLPEDODQFHZLOOYRLG
the warranty.
Ɣ+LJKS+KDUGZDWHUZLOOUHVXOWLQZKLWHFRDJXODWLRQVLQVLGHWKHILOWHUSXPSZKLFKPD\OHDGWRSXPS
damage.
WATER TREATMENT:
Ɣ3UHVVWKH%XEEOHEXWWRQRQWKHVSDZLUHGFRQWUROOHUWRWXUQRQWKHEXEEOHDLUEORZHUDQGKHOS
dissolving the chemicals into the water.
Ɣ1HYHUPL[FKHPLFDOVWRJHWKHU$GGWKHFKHPLFDOVWRWKHVSDZDWHUVHSDUDWHO\7KRURXJKO\GLVVROYHHDFK
chemical before adding the next one to the water.
BUBBLE