M-Spa Premium 2019 User manual

2019 Premium Concept Elite Service Manual
Visit our website at: www.the-mspa.com
- 1 -
After-sales Service Manual
Elite, Premium, Concept Spa
(EU,UK,SW)
Oriental Recreational Products (Shanghai) Co., Ltd.

2019 Premium Concept Elite Service Manual
Visit our website at: www.the-mspa.com
- 2 -

2019 Premium Concept Elite Service Manual
Visit our website at: www.the-mspa.com
- 3 -
Chapter 1 After-sales Service Center Operation and Warranty Policy
1.1 After-sales Service Center Set-up
ORPC authorizes After-sales service center in each specified country, region or territory. ORPC requests its service
center have necessary staff, equipment and facilities to ensure effective, professional and cost-saving warranty
services provided to MSpa customers. The service center must be eligible for the following requirements:
1.1.1 Have a service telephone or hotline number for customers to call for warranty services or product related
inquiries. The service number must keep in service during work days and normal business hours.
1.1.2 The service center must have dedicated staff - customer service representatives or technician to answer
phone calls, product inquiries or any other warranty related questions.
1.1.3 Provide a properly sized warehouse to store MSpa spare parts and returned defective parts from
customers.
1.1.4 Have a workshop to test and repair defective spas that defects cannot be solved by telephone service.
Repair service must be under valid warranty period.
1.1.5 Have necessary equipment or tools for a service engineer to carry out the warranty services efficiently.
1.1.6 Set up service procedures to guide and monitor service staffs’ daily service activities, include answering
customers’ phone calls, providing the service, recording service details, and filling in the service report.
1.2 Obligations of the After-sales Service Center
As an ORPC authorized After-sales service center, it is responsible to take care of all after-sales service related jobs
for MSpa customers in the specific territory at its own cost:
1.2.1 Listen to and answer customers’ phone calls, inquiries, or warranty claims in a timely, polite and
professional way
1.2.2 Verify warranty claims; decide if it’s valid or not according to the warranty policy by ORPC.
1.2.3 Provide technical services by phone to solve simple warranty issues that are not required of returning
product for testing and repair.
1.2.4 Test and repair the returned warranty spa products and ship back or return the repaired units.
1.2.5 Deliver replacement spare parts to customers if the spa is under warranty, and if customers are willing and
capable of repairing the spa by themselves.
1.2.6 Record and summary service details by filling in the service report. ORPC requires after service center to
submit the summary reports regularly for technical analysis and warranty re-verification purposes. The
service report should include the following:
Model Number
Serial Number
Customer Name & Contact Information
Purchase Date
Claim Date

2019 Premium Concept Elite Service Manual
Visit our website at: www.the-mspa.com
- 4 -
Defect Description
Defective Part Name
Repaired or Replaced Part Name and Quantity
Warranty Service Period
Photocopy of Customers’ Purchase Invoice
Photo of Defective Spa/Part etc.
1.2.7 For any serious quality problems or special warranty issues, the after-service center MUST report to ORPC
for approval or confirmation.
1.2.8 Manage spare parts inventory effectively, do stock checking regularly and submit the stock inventory
list/Consumption report to ORPC monthly.
1.2.9 Mspa service partner/distributor shall prepare monthly warranty service report in ORPC’s template and submit to
ORPC’s After-sales service department on every second Monday of the following month.
1.3 ORPC Warranty Policy
ORPC provides warranty for MSpa bubble spa products against defects in materials or workmanship under proper
usage and maintenance.
1.3.1 Warranty for Distributors/Importers
MSpa distributors and importers are entitled to manufacturer's warranty from the date of product arrival at the
destination port. ORPC/MSpa is only responsible for providing parts, but not services or any labor costs.
Warranty Items:
Mspa Model: C-MO049,C-MO069;
E-BA049,E-RE049,E-BL069,P-MB049,P-MB069,P-SH069,P-CA049,P-CA069,P-EX049,P-EX069,P-TU049,P-
TU069
Warranty Period:
Fifteen(15) months ( including three(3) months of storage period ) for the Premium/Elite/Mono series spa
pool
Fifteen(15) months ( including three(3) months of storage period ) for the electric part
Twenty-seven (27) months ( including three(3) months of storage period ) for the Premium Tuscany Rigid
wall
Nine(9) months ( including three(3) months of storage period ) for other spa components like inflatable
bladder, spa cover, and other non-electric part
Warranty Starting Date: MSpa distributor/importer warranty starts from the product arrival date at the destination.
1.3.2 Warranty for Consumers
Consumers are entitled to standard consumer warranty from the date of purchase. During the standard consumer
warranty, ORPC/MSpa will only provide parts to carry out the warranty repair. The distributor/importer is responsible

2019 Premium Concept Elite Service Manual
Visit our website at: www.the-mspa.com
- 5 -
for all the other costs, including but not limited to labor cost, shipping, and other service related cost. Under all
circumstances, it is the importer/distributor’s responsibilities to honor the consumer warranty.
Warranty Items:
Mspa Model: :C-MO049,C-MO069;
E-BA049,E-RE049,E-BL069,P-MB049,P-MB069,P-SH069,P-CA049,P-CA069,P-EX049,P-EX069,P-TU049,P-
TU069
Standard Consumer Warranty Period:
Twelve(12) months for the spa pool
Twelve(12) months for the electric part
Twenty-four (24) months for the Premium Tuscany Rigid wall
Six (6) months for other spa components like inflatable bladder, spa cover, and other non-electric part
Warranty Starting Date: End customer warranty starts from the date of purchase. Standard consumer warranty
applies ONLY to the original MSpa owners.
1.4 ORPC Warranty Obligations to Distributors/Importers
As the manufacturer, ORPC provides sufficient support to the authorized After-sales service center to carry out the
warranty service by the following activities:
1.4.1 Provide free spare part to the After-sales service center for valid distributor warranty claims.
1.4.2 Provide and update the service manual and other technical documents regularly. Provide training on warranty
policies, procedures, and other technical service issues.
1.4.3 Provide daily technical support to solve warranty problems effectively and smoothly through email or phone
calls.
1.4.4 Provide technical service training at Shanghai headquarter upon After-sales service center’s requests.
1.4.5 Collect, summarize and analyze the regional/territory service reports for future improvements in regards to
product quality or service.
Chapter 2. Important Information and Tips for Using Spa Products
2.1 Heating Effect -Temperature Increasing Rate or Speed
For 220-240V 50Hz Spa (EU Standard)
For 2-4 person bubble spa, the heat increasing rate is about 1.5-2.5 ℃/hour. To get a better heat increasing result, put
on spa inflatable bladder and top lid when the heater is on.
For 6-person bubble spa, due to larger water capacity, the heat increasing rate is lower at 1.2-1.8 ℃/hour.

2019 Premium Concept Elite Service Manual
Visit our website at: www.the-mspa.com
- 6 -
Heat Preservation Mat is helpful to reduce heat loss from the bottom and it provides better heat insulation results
together with the inflatable bladder in use. It is recommended to have the MSpa heat preservation mats in between the
SPA and ground. Consumers can also apply similar mat which is made of foam material or other material with heat
insulation function.
It’s only possible to set up and leave the spa at an outside temperature lower than 4°C as long as the spa has a
constant water temperature guaranteed at above 4°C. The spa can be used under low-temperature
environment and temperature down to maximum -10°C ONLY if it is set up properly to ensure no frozen water
inside control box, pipes or spa pool.
2.2 Filter Cartridge
MSpa filter cartridge –Item No. B0301964/B0302860 is suitable for all Mspa bubble spa products.
2.3 Inflate and Deflate the Spa (For Premium/Elite series only)
Note:
Check before inflation whether the manometer cap is screwed up tight on the valve of the pool
body. If not, please tighten and then inflate. After inflation, the manometer cannot be removed,
otherwise, air will be released.
When the Yellow section is pushed out, the Spa inflation is completed. You can fill the Spa with water.
After water filling is completed. Check air pressure once again to ensure the manometer reaches
Green section. Always ensure the manometer is on Green section at use.
If the White section of the manometer appears, the spa is over inflated. Rotate the valve cap counter
clockwise, have the air released till the Green section is pushed out, then tighten it clockwise.
To avoid over inflation caused by warm weather or sunshine when leaving spa for weeks inflated and
filled with water in temperature higher than 20°C (68°F), please release some air to make sure the
manometer is always on Yellow section.
Spa Deflation
1. Unscrew the manometer cap on the spa pool to deflate the spa.
2. Once the deflation is completed, screw the cap back.
Stop pressing bubble button and turn the knob back to <OFF>

2019 Premium Concept Elite Service Manual
Visit our website at: www.the-mspa.com
- 7 -
2.4 Avoid Air Leakage from Spa Liner Split or Tiny Holes Due to Over-inflation (For
Premium/Elite series only)
2.5 Try to Repair the Tiny Holes or Split on Spa Liner Instead of Replacing a New Spa Liner
For pool liner air leakage caused by tiny holes or splits, it is suggested to first try to repair with glue and PVC
swatches provided in the repair kit. You can also order repair swatches from the spare part list.
With the repair material, most pin holes and splits can be repaired easily within 10 minutes.
Spa Tub and Air Bladder Repair
Use the enclosed repair patch to repair any puncture:
1. Clean and dry the area to be repaired thoroughly
2. Apply the glue to the PVC patch and quickly attach it onto the damaged surface
3. Smooth the surface to remove any air bubbles and allow it dry for 5-10 minutes
NOTE: Glue is not included. Aquaseal & Stormsure glue is recommended for PVC inflatable items.
Glue physical and technical information:
2.6 Using Spa in the Cold Weather
It’s only possible to set up and leave the spa in the environment of an outside temperature of less than 4°C as long as
the spa has a constant water temperature guaranteed over 4°C. Spa can only be used for temperature down to
maximum -10°C if it is properly set up to make sure no frozen water inside control box, pipes and spa pool.
Standard accessories(Except P-SH069 & E-BL069):
Ensure to ask customers to test the spa pool air pressure with manometer. Testing air pressure
is very critical during the installation process, because any air leakage, pool liner splits due to
over inflation are not covered by the ORPC/MSpa warranty. It is important to advise customers
to watch the MSpa DVD or follow the instruction manual carefully to check and test the air
pressure every single time before inflating or using the spa.

2019 Premium Concept Elite Service Manual
Visit our website at: www.the-mspa.com
- 8 -
B9300109N/B9300492N Heat Preservation Mat is helpful to avoid heat loss from the bottom
and it provides better heat insulation results.
Inflatable bladder provides better heat preservation and rain outflow.
2.7 Temperature issue
If customer asks about temperature display on the control panel cannot reach to the set temperature of 42℃
(Maximum) and it indicates 38℃, 39℃, 40℃and 41℃, we may explain to the consumer that it is normal to show a
minor difference from the actual temperature to the rate displays on the control panel. It’s normal with a 1-2℃gap.
2.8 Broken zipper issue
Regarding broken zipper complaint, first, check if the air pressure is within the normal range. Over-inflated spa liner
could damage the spa cover zipper.
A replaced top lid may not 100% fit to the spa pool. 3-4cm (1-2”) difference is common. Because there might be a little
zipper length difference between the new top lid or spa liner and the used ones. To avoid zipper claim, please
recommend the customer to maintain the zipper by waxing it regularly.
2.9 Water treatment
Read through the “Water Quality & Filter” sections in the user manual. Always shower before entering the MSpa!
For user’s health, test your spa water chemistry and balance the pH, chlorine and alkalinity levels by using the test strip
every time before using it. The most desired pH level for a spa is between 7.2 and 7.8. Total alkalinity level is
suggested to set between 80 and 120ppm and free chlorine between 3 to 5ppm. Too low of a pH level will result in
excessive wrinkles and damage to the spa pool as well as corrosion in the motor unit. Too high of a pH level (hard
water) will result in scale incrustation, e.g. sheets of white coagulation inside the filter pump, which will lead to block
and non-working of the filter pump.
If you have any questions regarding chemicals usages, please contact your local spa/ pool water treatment specialty
stores.
It is the spa owner’s responsibility to have water maintenance properly. MSpa/ORPC is not responsible for any
damages that result from improperly maintained water. Improper water maintenance may result in voiding the warranty.
Warning
• Never mix chemicals together. Add the chemicals to the spa water separately. Thoroughly dissolve each
chemical before adding to the water.
• Brome or chlorine is highly recommended for good water quality.
• Please note that chlorine and bromine products should never be mixed. This is extremely dangerous. If you
usually use chlorine-based products and you want to switch to bromine-based products or vice versa, it is
mandatory to completely change the spa water before any chemicals changes.
• Do not overuse the chemicals, otherwise, there will be strong chemical odor and bring potential hazard to your
skin

2019 Premium Concept Elite Service Manual
Visit our website at: www.the-mspa.com
- 9 -
HTH BROMINE information (Recommend by Mspa European service partner)
Characteristics:
The use of bromine is particularly recommended in spas and heated waters over 27 ° C. It remains disinfectant
even at high PH. of the original product (sodium bromide), Bromine takes its disinfecting action but also its
non-aggressive properties. Has no odor, stings neither the eyes nor the skin and does not bleach the hair.
• 20 g tablet with slow dissolution, no residue
• Active ingredient content (BCDMH) greater than 96%
• Excellent disinfectant activity, regardless of the ph of the treated water (98% at ph 7.0 and still 75% at ph 8.2)
Safety with chemicals
Properly handled and used, the chemicals used in the maintenance of your spa are perfectly safe and harmless. If
you use them inappropriately or do not follow the instructions on the package, the consequences can be severe.
Here are some simple rules to always keep in mind:
• Keep chemicals in their original packaging.All products in the HTH Spa range are sold in one-certified packaging.
• Keep chemicals in their closed packaging when not in use.
• Keep all chemicals out of the reach of children.
• Never mix chemicals with each other. When you mix them with water, always add the products to the water, not
the water to the products.
• Store your SPA chemicals by following the instructions on the package.
• If you accidentally spill a product, clean immediately. If it is a solid product, use a shovel and a brush, and add it to
your spa in small quantities at a time.
Do not put the products back in their original packaging and do not use a household vacuum cleaner.
Bromine Kit (Recommend by Mspa European service partner)

2019 Premium Concept Elite Service Manual
Visit our website at: www.the-mspa.com
- 10 -
Bromine spa treatment kit. The essential kit for your spa water maintenance.
Includes:
1kg OVY Spa Bromine 20g Tablets
1kg OVY Spa Bromine Shock powder
1.5kg OVY Spa pH-minus powder
1L OVY Spa Anti-algae liquid
50 Bromine strips:Aquacheck
1 measuring cap
Mspa clean (Recommend by Mspa European service partner)
Spatime range by Bayrol The Spatime water line cleaner is ideal to easily clean the inside of the spa and eliminate
the impurities and the greasy sediments. Condensed liquid cleaner
2.10 Where to find MSpa serial number?
On the bottom of the control box or back of the wired controller panel near the rating label.

2019 Premium Concept Elite Service Manual
Visit our website at: www.the-mspa.com
- 11 -
Chapter 3. MSpa Assembly, Wire Diagram & Major Electric Parts
3.1 MSpa Assembly

2019 Premium Concept Elite Service Manual
Visit our website at: www.the-mspa.com
- 12 -
No.
Parts name
Parts qty
Material
Remark
1-86
Control box
1SET
Metal parts + silica
gel parts + plastic
parts
Exploded drawing as below
87
JET Assembly
element
2（3）SET
Foam + metal +
plastic parts
For Elite series only（Elite 4
person model- 2 Sets of
jets, 6 person model- 3 Sets
of jets）
88
Pool liner
1SET
PVC
89
Pool cover and
inflatable
bladder
1SET
PVC
90
JET cable
1
Rubber+Cu
For Elite series only
91
Bottom drain
assembly
1
plastic component

2019 Premium Concept Elite Service Manual
Visit our website at: www.the-mspa.com
- 13 -
3.2 MSpa Major Electric Parts
Wired control panel power board Main Power board (PCB)

2019 Premium Concept Elite Service Manual
Visit our website at: www.the-mspa.com
- 14 -
(PCB)
Transformer Filter pump
Bubble generator PTC heater
Ozone generator JET Pump
3.3 Wiring Diagram

2019 Premium Concept Elite Service Manual
Visit our website at: www.the-mspa.com
- 15 -

2019 Premium Concept Elite Service Manual
Visit our website at: www.the-mspa.com
- 16 -
Chapter 4 How to Replace Mspa Parts
4.1 Power Board Assembly and Wire Terminal Connection
Elite series with JET brown cable and jet blue cable connected
Premium series without JET brown cable and jet blue cable due to no Jet
function
The other wire connections are the same for Elite and Premium series
JET blue
cable
Heating loop
black line
Blue
power
supply
BUBBLE
Brown
cable
Transformer
Brown
cable
Brown
power
supply
JET
Brown cable
flow switch
insert（big）
Temperature
sensor insert
(small)
four-core
data cable
flow switch
insert（big）
microswitch
insert
O3
generator
Brown
cable
Transformer
blue cable
O3 Generator blue cable
BUBBLEblue cable
Heating double circuit
connection (white)

2019 Premium Concept Elite Service Manual
Visit our website at: www.the-mspa.com
- 17 -
4.2 How to replace the control box (Premium/Elite)
1. Empty water in the spa pool and deflate the spa and
then screw off water inlet and outlet fittings with a
plastic wrench that was supplied in the spa package；
2. Remove the knob switch (as shown in the video)
3、Remove the fixed ring of the water drainage
assembly；
4.1、Remove the fixed pressure plate of JET power
cord；（ For Elite series only, video available: How to
disconnect Jet cable before taking out control box）
4.2、Disconnect two pairs of JET inserts from JET
cable insertion hole（For Elite series only）
4.3 Unscrew the PE air pipe；
5、Unscrew the check valve’s connection plastic nut；
6、Take out the control box from the pool liner; pull out
1
2
1
JET cable
insertion
hole

2019 Premium Concept Elite Service Manual
Visit our website at: www.the-mspa.com
- 18 -
the smart control panel from the hole of pool liner.
7. Dissemble the plug and upper foam from the original
control box, then mount to the new replaced control box.
8、Assemble back new replaced control box into pool
liner in reverse order. (Video available)
4.3 Replace the bubble generator(B9301054)
1. Take out the control box
2. Loosen four screws (ST4*60) from the bottom of the
cabinet
3. Loosen five screws(ST4*15) from the rear cover
of the cabinet; Loosen two screws (ST4*15) from the
bottom of the cabinet
4. Take out the internal cabinet and power board
5. Loosen screws and disassemble the top cover
from the bubble generator
6. Remove the connection of leading wire and take out
the bubble generator

2019 Premium Concept Elite Service Manual
Visit our website at: www.the-mspa.com
- 19 -
7. Put the new bubble generator; assemble the heat
shrinkable sleeving; connect the leading wire from
the bubble generator and power cable.
8. Connect the transparent protective suit on the lead to
the joint，assemble the heat shrinkable sleeving;
Tie-binding after fusing shrinkage
9、Assemble the control box in reverse order. (Video available)
4.4 How to replace heating element(B9301283 + B9301284)
1、Take out the control box
2、Loosen four screws (ST4*60) from the bottom of the
cabinet
3、Loosen five screws (ST4*15) from the rear cover
of the cabinet; Loosen two screws (ST4*15) from the
bottom of the cabinet
4、Take out the internal cabinet and power board；
5、Loosen three screws from the fixed junction box;
disassemble 4 sets black pin-cables；
6、Remove 4 screws and open the wire connection box;
cut off the bindings and take out the 2 heating wires,

2019 Premium Concept Elite Service Manual
Visit our website at: www.the-mspa.com
- 20 -
7、Loosen 6 screws from the filter pump
8、Loosen 1 screw from the bubble generator to PTC
heater; 2 screws from the fixed mount; 2 screws from the
outlet of PTC heater
9. Remove the binding band of the O3 inlet pipe on the
PTC assembly and remove the O3 inlet pipe；
10、Use cross screwdriver to disassemble the 2 heating
earth wire
11、Take out the PTC heating element and filter pump; disassemble the metal band from the outlet of the filter
pump.
12、Assemble the new PTC heater back into the control box in reverse order. (Video available)
4.5How to replace transformer (B9300933)
1、Take out the control box；
2、Loosen four screws(ST4*60) from the bottom of the