M-Spa Mont Blanc P-MB06 User manual

EN
DO NOT RETURN MERCHANDISE TO YOUR DEALER STORE DIRECTLY. CALL MSPA AFTER
SALES SERVICE CENTER FOR PRODUCT QUESTIONS OR CONTACT MSPA AT
[email protected]
Due to MSpa continuous product improvement, MSpa reserves the right to change
specifications and product appearance, which may result in updates to the instruction
manual without notice.
M-009LS / 019LS
M-011LS / 021LS
D-TE06
M-029S
Alpine
Silver Cloud
Tekapo
Soho
M-031S
M-051S
M-113S / 115S
P-MB04 / MB06
Camaro
Super Camaro
Luxury Exotic
Mont Blanc
Where Luxury Is Affordable
www.the-mspa.com
MSpa®
Owner’s Manual

2
ENTER THE WORLD OF MSPA
Thank you for choosing MSpa and for your confidence in our brand. We believe that you will enjoy many benefits
of using MSpa products for years to come.
To guide you in your initial MSpa experience, we are pleased to present you with this instruction manual. Please
carefully and thoroughly read this manual entirety before using the product for the first time.
We are delighted to welcome you to the MSpa family, and look forward to sharing with you the full spectrum of
our expertise.
Enjoy your MSpa!
Scan the QR code to enter the MSpa official website
CONTENT
Safety precautions………………………………………………………………......................................................
Specifications and product overview…………………………………………………..........………........................
First use and set-up preparation………………………………………………….........................……………........
Spa set-up……………………………………............................…………………………......….............................
Control panel operation…………………………………………........................…................................................
Water maintenance and chemicals………………….......................................………..………………..…...........
Drainage, cleaning and storage………………………...................................………………..………..……..........
Disposal and environmental protection…………………………................................…......................................
Troubleshooting…………………………………………….......……………………….…...…...…..........................
MSpa limited warranty policy.............................................................................................................................
MSpa LITE limited warranty policy....................................................................................................................
3
7
10
12
16
17
19
20
21
22
23
Welcome,

3
SAFETY PRECAUTIONS
For your own safety and that of your product, make sure to follow the safety
precautions below. Fail to follow the instruction may result in serious injury,
property damage or death. Improper installation or operation will void the warranty.
READ, UNDERSTAND AND FOLLOW ALL INSTRUCTIONS
! DANGER
Risk of Accidental Drowning. Extreme caution must be exercised to prevent
unauthorized access by children.
Risk of drowning. Inspect the spa cover regularly for leak, premature wear and
tear, damage or signs of deterioration. Never use a worn or damaged cover: it
will not provide the level of protection required to prevent unsupervised access
to the spa by a child.
Risk of drowning. Always lock the spa cover after each use.
Risk of injury. If the supply cord is damaged, it must be replaced by the manu-
facturer, its service agent or similarly qualified persons in order to avoid a
hazard.
Risk of Electric Shock. Do not permit any electrical appliances, such as a light,
telephone, radio or television within 1.5m (5 feet) of a spa tub.
Risk of Electric Shock. Do not use the spa when it is raining, thundering or
lightning.
●
●
●
●
●
●
To reduce the risk of electric shock, do not use an extension cord, timers, plug
adaptors or converter plugs to connect the unit to electric supply; provide a
properly located outlet.
Parts containing live parts, except parts supplied with safety extra-low voltage
not exceeding 12V, must be inaccessible to occupants in the spa.
Parts incorporating electrical components, except remote control devices, must
be located or fixed so that they cannot fall into the spa.
The appliance should be supplied through a residual current device (RCD) with
a rated tripping current not exceeding 30 mA.
●
●
●
●
! WARNING

4
Residential electrical connection box must be located safely with a distance of
at least 2m away from the spa.
Electric installation should fulfill the local requirement or standards.
Do not press down or uplift the control panel or put any heavy items on the
control panel after installations.
This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of experi-
ence and knowledge if they have been given supervision or instruction concern-
ing use of the appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user maintenance shall
not be made by children without supervision.
To reduce the risk or injury, do not permit children use this product unless they
are closely supervised all times.
To reduce the risk of child drowning, supervise children all times. Attach and
lock spa cover after each use.
Make sure the floor is capable of supporting the expected load, which you can
find from the spec sheet, calculate the expected load of water capacity plus total
weight.
Adequate draining system must be provided around the spa to deal with over-
flow water.
To reduce the risk of injury:
a) Lower water temperatures are recommended for young children and when
spa use exceeds 10 minutes. In order to avoid the possibility of hyperthermia
(heat stress) occurring it is recommended that the average temperature of
spa-pool water should not exceed 40°C(104°F).
b) Since excessive water temperatures have a high potential for causing fetal
damage during the early months of pregnancy, pregnant or possibly pregnant
women should limit spa water temperatures to 38°C(100°F).
c) Before entering a spa or hot tub the user should measure the water
temperature with an accurate thermometer since the tolerance of water
temperature regulating devices varies.
d) The use of alcohol, drugs or medication before or during spa use may lead to
unconsciousness with the possibility or drowning.
e) The use of alcohol, drugs, or medication can greatly increase the risk of fatal
hyperthermia in spas.
f) The causes and symptoms of hyperthermia may be described as follows:
Hyperthermia occurs when the internal temperature of body reaches a level
●
●
●
●
●
●
●
●
●

5
several degrees above the normal body temperature 37°C(98.6°F). The
symptoms of hyperthermia include an increase in the internal temperature of
body, dizziness, lethargy, drowsiness, and fainting. The effect of hyperemia
include failure to perceive heat; failure to recognize the need to exit spa;
unawareness of impending hazard; fetal damage in pregnant women;
physical inability to exit the spa; and unconsciousness resulting in the danger
of drowning.
g) Obese persons or persons with a history of heart disease, low or high blood
pressure, circulatory system problem, or diabetes should consult a physician
before using a spa.
h) Persons using medication should consult a physician before using a spa
since some medication may induce drowsiness while other medication may
affect heart rate, blood pressure, and circulation.
i) Check with doctor before use if pregnant, diabetic, in poor health, or under
medical care.
People with infectious disease should not use a spa or hot tub.
To avoid injury exercise care when entering or existing the spa or hot tub.
Water temperature in excess of 42°C(108°F) may be injurious to your health.
Never use a spa or hot tub alone or allow others to use the spa alone.
Do not use a spa or hot tub immediately following strenuous exercise.
Spa heat in conjunction with alcohol, drugs, or medication can cause uncon-
sciousness.
Exit immediately if uncomfortable, dizzy, or sleepy. Spa heat can cause hyper-
thermia and unconsciousness.
Do not put the spa under 0°C(32°F) environment in order to avoid freezing if
there is still water in the pool.
It’s helpful to put temp barrier mat in between the spa pool and the ground.
Similar mat which is made of foam material or other materials with heat barrier
function can also be used. Do not turn on the spa when the water is frozen.
Never pour water with a temperature higher than 40°C(104°F) into the spa
directly.
Always unplug this product from the electrical outlet before removing, cleaning,
servicing or making any adjustment to the product.
Never jump or dive into a spa or any shallow body of water.
No part of the electric appliance is to be located above the bath during use.
Do not bury the electrical cord. Locate the cord where it will not be damaged by
lawn mowers, hedge trimmers and other equipment.
●
●
●
●
●
●
●
●
●
●
●
●
●

6
Do not attempt to plug in or unplug this product while standing in water or when
your hands are wet.
Do not use the spa if damaged in delivery and/or malfunctioning in any way.
Contact the MSpa service center for further direction.
Keep all pets away from the spa to avoid any damage.
Do not add bath oil or bath salt to the spa water.
●
●
●
●
The cleaning and disinfection please see below and see “WATER MAINTAINCE
AND CHEMICALS.
Always add chemicals to water, never add water to chemicals. Adding water to
chemicals may cause strong fumes or violent reactions and hazardous chemical
spray.
For water already used, discharge it in time or use water chemicals for cleaning.
Usually,change water every 3-5 days.
Use Mspa chemical kit for disinfection in accordance with manufacture's
instructions.
Do not leave or set up the spa in temperature lower than 4°C(39°F) if heater is
not operating.
Always enter and exit the spa or hot tub slowly and cautiously. Caution of wet
floor.
To avoid damage to the pump, never turn on the spa or hot tubs unless it is
filled with water to the minimum water line.
Place the spa or hot tub only on a properly prepared site that can withstand the
floor loading requirement of the spa.
Do not leave the spa empty for extended period of time. Drain away water
inside the pool thoroughly for long time disuse. Do not expose the spa under
direct sunshine. Check regularly before each use. Put away the spa or fence it
up in time after using.
Open the spa top lid when the Bubble function is on.
In order to avoid a hazard due to inadvertent resetting of the thermal cut-out,
this appliance must not be supplied through an external switching device, such
as a timer, or connected to a circuit that is regularly switched on and off by the
utility.
●
●
●
●
●
●
●
●
●
●
●
! CAUTION

7
SPECIFICATIONS
4 + 2
4
4
4
6
6
6
PREMIUM BUBBLE SPA
Model No. / Code Shape Seating
Capacity
Water
Capacity
Outside
Dimensions
Inside
Dimensions Height Weight
M-029S / Soho
P-MB04 / Mont Blanc
M-031S / Camaro
M-113S / Luxury Exotic
P-MB06 / Mont Blanc
M-051S / Super Camaro
M-115S / Luxury Exotic
Square
Round
Round
Round
Round
Round
Round
930Ltr
(245gal)
700Ltr
(184gal)
700Ltr
(184gal)
700Ltr
(184gal)
930Ltr
(245gal)
930Ltr
(245gal)
930Ltr
(245gal)
1.85m
(73”)
1.80m
(71”)
1.80m
(71”)
1.80m
(71”)
2.04m
(80”)
2.04m
(80”)
2.04m
(80”)
1.45m
(57”)
1.40m
(55”)
1.40m
(55”)
1.40m
(55”)
1.60m
(63”)
1.60m
(63”)
1.60m
(63”)
0.68m
(27”)
0.70m
(28”)
0.70m
(28”)
0.70m
(28”)
0.70m
(28”)
0.70m
(28”)
0.70m
(28”)
34kg
(75lbs)
30.5kg
(67.2lbs)
30.5kg
(67.2lbs)
32kg
(70.5lbs)
34kg
(75lbs)
33.5kg
(73.9lbs)
35kg
(77.2lbs)
Control System Specs
Control System
Total Power
Heater
Massage Air Blower
Filter Pump
Cord Mounted
Top Lid
Pool Cover
Pool Material
M-029S / 031S / 051S / 113S / 115S P-MB04 / MB06
220-240V/50Hz
2300W
1500W/2.04HP
720W/1HP
12V/60W
AU: RCD plug
Premium PVC leather cover with foil inside
Premium PVC tough leather, waterproof and anti-UV
Premium PVC fabric

8
Control System Specs
Control System
Total Power
Heater
Massage Air Blower
Filter Pump
Cord Mounted
Top Lid
Pool Cover
Pool Material
M-009LS / 019LS / M-011LS / 021LS D-TE06
220-240V/50Hz
2300W
1500W/2.04HP
720W/1HP
12V/60W
AU: RCD plug
Rhino-Tech™ reinforced PVC with foil inside
None
Premium PVC fabric
Model No. / Code
2 + 2
4 + 2
4
6
4 + 2
LITE BUBBLE SPA
Shape Seating
Capacity
Water
Capacity
Outside
Dimensions
Inside
Dimensions Height Weight
M-009LS / Alpine
M-019LS / Alpine
M-011LS / Silver Cloud
M-021LS / Silver Cloud
D-TE06 / Tekapo
Square
Square
Round
Round
Square
650Ltr
(171gal)
930Ltr
(245gal)
700Ltr
(184gal)
930Ltr
(245gal)
930Ltr
(245gal)
1.58m
(62”)
1.85m
(73”)
1.80m
(71”)
2.04m
(80”)
1.85m
(73”)
1.18m
(46.5”)
1.45m
(57”)
1.40m
(55”)
1.60m
(63”)
1.45m
(57”)
0.68m
(27”)
0.68m
(27”)
0.70m
(28”)
0.70m
(28”)
0.68m
(27”)
24kg
(52.9lbs)
27.5kg
(60.6lbs)
23.5kg
(51.8lbs)
26kg
(57.3lbs)
28.5kg
(62.8lbs)

9
PRODUCT OVERVIEW
Packaging content
NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale.
A. B. C. D.
E. F. G. H.
I. J. K.
M. N. O.
L.
®
®
®
®
round or square
* optional
* Only for M-031S/M-051S
P-MB04/P-MB06
M-009LS/019LS/029S / D-TE06
*Ground mat
®
GH
*Buckle spa cover

10
FIRST USE AND SET-UP PREPARATION
The spa can be installed indoor and outdoor. For household use only.
The spa must be set up on a flat, smooth and supporting surface that is capable of supporting the maximum
load of the filled spa with listed maximum occupants.
Make sure the area is free of sharp objects under or around the spa. Uneven of unsound surfaces can
damage the spa and void your warranty. Level the surface before filling spa with water.
Provide adequate drainage system around the spa to deal with overflow water and splashes.
Provide a properly located power outlet to connect the spa.
Make sure there is enough clearance around the spa for full access to the spa equipment for maintenance
and/or service.
●
●
●
●
●
●
Site preparation and requirements
Verify the supporting floor can support the filled weight of spa with maximum number of occupants. Check
with a qualified contractor or structural engineer to verify the requirement.
Make sure the floor is water resistant and provides non-slip surface. Do not install the spa on a carpet of
any other material that could damaged by the moisture.
Humidity is a naturally side effect of indoor spa installation. The room shall be properly ventilated to allow
moisture to escape. Install a ventilating system to prevent excess condensation moisture in the room.
●
●
●
Additional requirements for indoor installation
REF. NO. PARTS DESCRIPTION QTY.
NOTE: When ordering parts, be sure to quote the model number and part numbers.
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
Spa cover with aluminum foil inside (M-009LS/019LS/029S/D-TE06 excluded)
Spa tub
Control panel with air pipe
Heat preservation bubble mat (*optional for MSpa LITE products)
Heat preservation foam mat (For M-113S/115S)
Digital lock (except for M-009LS/019LS/029S/D-TE06)
Inflation hose for spa tub and bladder
Manometer
Filter cartridge (twin pack for PREMIUM Bubble spas, 1pc for LITE Bubble spas)
Spa drain valve adaptor
Repair kit
Spa cover inflatable bladder (*optional for MSpa LITE products)
Wrench
Buckle spa cover and ground mat set (For M-009LS/019LS/029S/D-TE06)
Instruction DVD
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1

11
Make sure to set up the spa on a firm, level and smooth surface that is strong enough to support the full
weight of the filled spa and maximum occupants.
Do not set up the spa on grass or dirt, as this increases the amount of debris entering the spa, and
damage the spa floor.
Do not leave the spa tub exposed to direct sun light for extend period of time.
It is possible to install and leave the spa outside at a temperature not lower than 4°C(39°F) and the water
inside the circulation system, pump, pipe are not frozen. Put a Heat Preservation Mat in between the spa
bottom and the ground to prevent heat loss from the bottom of the spa and to provide better heat retention.
●
●
●
●
Additional requirements for outdoor installation
Plug the machine into the mains.
Press the RESET button on the RCD. The indicator turns red.
Press the TEST button on the RCD. The RCD indicator should shut off.
If the RCD indicator does not turn off, the RCD is faulty. Do not use the spa. Contact a qualified electrician to
correct the fault.
Press the RESET button on the RCD again. The indicator should turn red. If yes, the spa is ready for use.
1.
2.
3.
4.
RCD Testing
Risk of electric shock: This product is provided with a RCD located at the end of the power cord. The RCD
must tested before each use. Do not use the spa if the RCD does not function properly. Disconnect the
power cord until the fault has been identified and corrected. Contact a licensed electrician to correct the
fault. There are no serviceable parts in side the RCD. Opening the RCD will void the warranty.
1. 2.
RESET
3.
TEST
4.
Indicator area
! WARNING

12
SPA SET-UP
Move the entire package to the selected site. Open the carton carefully as it can be used to store the spa
during long term storage or when not in use.
Lay out all the parts on the ground and check as per Packaging Content list. Make sure the spa tub is right
side up. (*For missing or damaged part, contact the MSpa Service Center)
Spread the Heat Preservation Ground Mat over a cleared area. Spread out the spa liner over the ground
mat. Heat Preservation Mat prevents heat loss from the bottom of the unit.
NOTE:
The heat preservation ground mat is not included for MSpa LITE package. It is recommended to apply a
ground mat for the spa tub to prevent scratches or heat loss.
1.
2.
3.
1 2 3
M-009LS / 019LS / 029S /
D-TE06: Spread out the
square ground mat and
place it to the selected site.
Make sure the buckle of
cover and mat is attached
when spa not in use.
●
this side
face down
Connect the digital cable to the control panel. “ON/OFF” button shows red if the connection correctly,
No bent or wet for the pin inside male connector which will cause failure connection.
Connect the control panel to the spa tub. Fasten and secure the rings to the pipe adapter on the spa tub.
Make sure the rubber O-rings are properly placed on the air pipes.
CAUTION: Lost of the O-rings may result spa and the bubbling function working improperly, and also
cause the air pump rusted.
NOTE: For spa models with PVC leather covers, make sure the spa cover is placed onto the spa tub
properly before installing the control panel. The two holes on the PVC leather cover must be positioned
correctly to the pipes of control panel.
4.
5.
45
O-rings

13
Spa Inflation
6.1 Unscrew the air valve cap (a) on the control panel to reveal the air blower inflation outlet and connect
one end of the inflation hose (b) to the outlet. See Figure 5.1
6.2 Unscrew the air valve cap on the spa pool and reveal the stem for inflation.
6.3 Connect the other end of the inflation hose (b) to the manometer (c) first and then insert to the air
valve.
6.
11
6.1 6.2 6.3
(a)
(b)
(b)
(c)
6.4 Press the Bubble button to inflate the spa tub until it is firm to tough.
CAUTION: Do not over inflate. Over inflation may cause spa leakage and void the warranty.
6.5 Pay attention to the Manometer. The Yellow section appears when the spa is properly inflated. The
Green section shows when water filling is completed. Repeat previous steps if more air is necessary.
CAUTION: The Red section shows when the spa is over inflated. Press the black button (a) on the
manometer to release some air until it points to the green section.
IMPORTANT: During spa use, the manometer shall only show the Green section at all times.
6.6 When inflation is completed. Press Bubble button again to turn it off. Disconnect the inflation
hose on both ends. Screw the air valve cap back.
NOTE:
● The cap is designed to be screwed on and off. Never exert force as this could cause the complete
internal inflation system of the valve to come loose.
● If over inflated, remove the inflation hose from the spa air valve side, screw the valve cap to
release some air and stop until the manometer points to the right color section.
6.4 6.5
Green
Yellow
Over Inflation
Red
Button (a)
NOTE: Deflation Instruction
Spa Deflation
1. Unscrew the air valve cap on the spa pool to deflate the spa.
2. Once the deflation is completed, replace the cap back.

14
Water Filling
7.1 Check the spa liner is at the selected area and point
the drain valve toward a suitable draining area before
inflation.
7.2 Fill the spa tub with fresh water to a level between
Minimum and Maximum line marked on the inner
spa wall.
Do not over fill the spa. It is recommended to fill the spa with lukewarm water for quick heating and
energy saving.
WARNING:
● Water level must reach the Minimum water line but not exceed the Maximum line to avoid
pump failure.
● Never pour water with a temperature higher than 40°C(104°F) into the spa directly.
● To avoid control system failure, do not operate the spa until water reaches the Minimum
line.
7.3 After water filling, double check the spa pool air pressure to make sure the manometer points out the
Green section.
7.4 Place the zipper spa cover over the spa tub, and make sure the spa cover zipper are closed and lock
the cover by the digital lock in the accessory pack.
IMPORTANT:
● Inspect the spa pressure regularly for leak, premature wear or deterioration.
● Check and wax the zipper regularly, to make it smooth for operation and avoid splits.
7. 7
7.5 Turn on the Heater on the spa control panel, refer to the “Control Panel Operation” section.
Maximum heating temperature is 42°C(108°F). Hourly heating rate is about 2°C-2.5°C(3.5°F-4.5°F)
for 2 and 2+2 persons, 1.5°C-2°C(2.5°F-3.5°F) for 4 persons and 1.2°C-1.8°C(2°F-3°F) for 6
persons.
Zipper and Buckle Operation
8.1 Digital Lock Operation
Original password is “000”. Following the steps below to change the password:
● Push the button (a) in the direction of Fig.8.1.(1) to unlock the digital lock.
● Set your preferred password in 3 digits by turning the number wheel (b), see Fig.8.1.(2).
7.4
8.

15
8.2 Square Spa Buckle Lock Operation
Lock the Buckle
● Insert the buckle on the Ground Mat into the Spa cover buckle, until you hear a “Click” sound.
Unlock the Buckle
● Pinch both sides of the locked buckle, and press down the round dot in center in the same time.
Press down the center button and release the lock.
® ®
®
(a)
(b)
(c)
8.1.(1) 8.1.(2) 8.1.(3)
Lock Unlock
8.2

16
CONTROL PANEL OPERATION
1. ON/OFF Button
2. Bubble Button
3. Filter Button
4. Heater Button
5. UP & DOWN Button
15
4 3 2
ON/OFF ON/OFF Button: To activate the control panel.
Default stand by mode shows red when the power is on. Press again, the control reaches
operative mode and turns to green.
Bubble Button: To activate the bubbling massage function, which has a 20-minutes auto
off for 10-mintues feature. The light of Bubble button displays green when activated.
Filter Button: Activate the filter pump. The light of the Filter Button displays green when
the filtration system is activated.
NOTE: Filtration cannot be turned off when Heating is activated. When the Heating function
is turned off, Filtration will stop after 30 seconds. Filtration function can be then
activated separately.
NOTE: Auto-filtration system every 4 hours.
Heater Button: Press this button to activate the HEATING and FILTRATION function at the
same time. The button turns green for 10s. The heater will heat the spa water until the water
temperature reaches the pre-set temperature. After the current water temperature drops by
2°C(3.6°F) below the set temperature, the heating system will restart automatically. When
the HEATER button turns red, the heating system is activated. When the HEATER button
turns green, the heating system is at rest as the water reaches the set temperature.
Temperature Adjustment Buttons: To adjust the temperature. You can set your
desired temperature by pressing “UP ▲” or “DOWN ▼” buttons.
LOCK THE SCREEN: Press “UP ▲” and “DOWN ▼” buttons together to lock the control panel to avoid any
wrong operation by children. Press the two buttons together once again to unlock the control panel.
IMPORTANT：The following conditions will lead to slow water heating
● The ambient temperature is lower than 10°C(50°F)
● Outdoor wind speed is above 3.5-5.4m/s(8-12mph)
● The air bubble function is activated when heater is on
● The spa is not properly covered with the spa cover when heater is on

17
LED READING CAUSE SOLUTION
E0
E1
E2
E3
Temperature sensor failure.
Water pressure switch failure
Filter failure
Water foils to reach the minimum water line
Detecting function failure
System failure
Contact the MSpa Service Center.
Contact the MSpa Service Center.
Add more water to the minimum line.
System self-checking
Step 1: Fill water to the water line, and
make sure there is no bather or
object in the spa tub.
Step 2: Connect the power supply, press
REST button on the RCD.
Step 3: If E3 shows, contact the MSpa
Service Center. If E3 is flashing,
press ON/OFF and BUBBLE
buttons together, enter the
self-checking system.If no error
code shows, failure is not detected.
It is OK to use the spa. If error
code shows after self-checking,
contact the MSpa Service Center.
Change the water or contact the
MSpa Service Center.
ERROR CODE CHART
Water temperature is lower than zero degree
or exceeds 55°C(131°F)
WATER MAINTAINCE AND CHEMICALS
Water Sanitation
The spa owner must regularly check and keep the spa water sanitized with scheduled maintenance (daily, if
necessary). Adding sanitizer or other chemical will control bacteria and viruses present in the spa water. The
maintenance of a proper water balance through appropriate use of sanitizers is the most important factor in
maximizing the life and appearance of the spa as well as ensuring clean, healthy and safe water.
Proper technique is important for water testing and treating the spa water. See your spa professional for
chemical, sanitizer, test kit and testing procedures questions.
Maintenance of Spa Water and Cartridge
Protect all the spa occupants from possible water related illness by keeping the spa water clean and sanitized.
Always practice good hygiene. To ensure proper spa water quality by following these procedures:
CAUTION:
● Always follow the chemical manufacturer’s guide, and the health and hazard warning.
● Do not add chemicals if the spa is occupied. This can cause skin or eye irritation.
● Concentrated chlorine solutions can damage the spa tub. Improper chemical use will void the warranty.

18
1. Inspect and clean the filter cartridge after each use, and change the filter cartridge after it works
continuously for 72 hours.
● Unscrew the cartridge assembly from the spa tub wall and remove the cartridge by turning it counter
clockwise (Fig. 1.1)
● Use a garden hose to rinse off the cartridge. If the cartridge remains soiled and discolored it should be
replaced. Keep spare cartridges on hand.(Fig.1.2).
● Reinstall the clean or spare cartridge back onto the spa tub wall but turning it on clockwise. (Fig.1.3)
1.1 1.3
2. Change the spa water every 3-5 days depends on the spa use. See “Draining, cleaning and storage”
section for instruction.
3. Use spa chemicals to maintain proper water chemistry. Spa damage resulting from misuse of chemicals
and mismanagement of spa water is not covered by the warranty. Consult your local spa or pool retailer for
more information on chemical use.
4. All occupants must shower before entering the spa.
5. When spa inlet or outlet is stuck with dirt, use the
Wrench to check the problem and clean the inlet
or outlet.
Water Balance
Maintain the spa water pH level between 7.2 and 7.8, total alkalinity between 80 and 120ppm and free chlorine
level between 3 to 5ppm. Use the *optional Test Strips to test the spa water chemistry before each use of the
spa and continue to test the water no less than once a week.
The Test Strips can test the “Free Chlorine”, “pH”, and “Total Alkalinity” level at the same time:
1. Dip the entire strip into the water and remove immediately
2. Hold the strip level for 15 seconds. Do not shake excess water from the strip
3. Compare the strip pad to the color chart on the packaging label. If necessary, adjust the chemical level in
the pool water
5
1.2
IMPORTANT:
● MSpa Water Treatment kit is strongly recommended for spa use.
● Press the Bubble button on the spa control panel to turn on the bubble air blower and help to
dissolve the chemicals into the water.
● Never mix chemicals together. Add the chemicals to the spa water separately. Thoroughly dissolve each
chemical before adding one to the water.
NOTE:
● Low pH will damage the spa tub and pump. Damage resulting from the chemical imbalance will void the
warranty.
● High pH (hard water) will result in white coagulations inside the filter pump; which may lead to pump
damage.

19
garden hose
Spa Tub Cleaning
If dirt is visible in the water or water becomes cloudy and proper water chemistry does not clear it up, change the
water and clean the spa tub.
While spa water is empty, remove the cartridge from the inside of the spa tub wall, clean and /or replace the filter
cartridge. Use a sponge and mild soap solution to wipe away any soil or stains on the inside of the spa wall. Rinse
thoroughly before refilling with clean water.
IMPROTANT: Do not use steel wool, hard brushes or abrasive cleaners.
Spa Tub and Air Bladder(*Optional) Repair
Use the enclosed repair patch to repair any puncture:
1. Clean and dry the area to be repaired thoroughly
2. Apply the glue to the PVC patch and quickly attach it onto the damaged surface. (Glue is not included)
3. Smooth the surface to remove any air bubbles and allow it dry for 5-10 minutes
DRAINAGE, CLEANING AND STORAGE
Spa Drainage
1. Turn off all the buttons (heater, filter and bubble) on the control panel unit.
2. Connect the drain valve adapter to a garden hose and point the other end of the garden hose to a
suitable draining area according to local environmental regulations (Fig.1)
3. Remove the drain valve cap from the outside of the spa tub and attach the drain valve adapter with the
garden hose to the drain valve (Fig.2)
4. From the inside of the spa tub, open the drain valve cap, water will start to flow out through the garden
hose (Fig.3)
5. When the water stops draining, lift the spa tub wall from the opposite to the drain, leading any remaining
water to the drain and empty the spa water completely. (Fig.4)
6. Press Bubble button to dry out any water in the piping system. Operate the bubbling function for
15 minutes to blow out all the remaining water. (Fig.5)
7. When the water stops draining, use a clean towel to wipe up any remaining water and moisture on the spa
tub and spa control panel. (Fig.6)
1
17
15
23
4 5 6

20
DISPOSAL AND ENVIRONMENTAL PROTECTION
This marking indicates this product should not be disposed with other household wastes.
To prevent possible harm to the environment or human health from uncontrolled waste
disposal, recycle it responsibly to promote the sustainable reuse of material resources.
You can obtain information on disposal from your local authorities.
To return your used device, please use the return and collection systems or contact the
retailer where the product was purchased. They can take this product for environmental
safe recycling.
Storage and Prepare for the Next Time Use
1. Drain and clean the spa by following the
“Drainage” and “Spa Cleaning” sections
2. Reserve the set up instructions to deflate and
disassemble the spa tub, spa control unit and
air bladder (*Optional)
3. Make sure all the spa components and
accessories are thoroughly clean and dry before
storage. Air-dry the spa tub in the mild sun for
an hour before folding
4. Fold the spa tub loosely and avoid any sharp
corners to prevent damage or leakage to the
spa liner
5. Prepare new additional cartridge for next time use
6. Store the spa and accessories in a dry, temperature
controlled, between 0°C - 40°C (32°F - 104°F) storage location
7. Original packaging is recommended to be used for storage
TM
SUN
1 32
pin holepin hole
NOTE: Glue is not included.