M3 Mobile M3 Orange Installation guide

www.m3mobile.net
M3 ORANGE+
Quick Manual Ver.1.0

01
PACKAGE
▪Please check all items below are included in package box.
< M3 ORANGE+ >
< USB cable >
OR
< Cradle >
※Warning
Use of controls or adjustments or performance of procedures other than
those specified herein may result in hazardous radiation exposure.
< Stylus pen >
< Adaptor >
< Battery >
< Snap-on >
※NOTE
For data synchronization,
either desktop cradle or
snap-on can be provided
depending on your purchasing
option.

02
FEATURES
Barcode Scan Window
Micro SD card slot
Scanner LED
GSM / WCDMA LED
Charging LED
POGO Pin
Keypad
Reset Button
Speaker
Stylus Pen
Camera
Flash
Volume Button
Scanner Button
Camera Button
LCD Touch Screen
Battery Lock
Battery cover
DEVICE

03
FEATURES
▪ M3 ORANGE+ has two types of keypad – Alphanumeric and QWERTY.
Some function keys may not work depending on its options.
<AlphaNumeric>
<QWERTY>
SCAN
SCAN
Soft 1
Send
Power
Input mode change
Windows
Back Space
Function
Navigation
Action (Enter)
Soft 1
end
Numbers
KEYPAD
Navigation
Soft 1
Send /
Windows
Shift
Function
Backlight toggle
Navigation
Soft 1
End/OK
Orange function
Power
Back Space
Characters

04
When an unexpected error occurs while using
the device, SOFT RESET allows your device
to restart, similar to rebooting a computer.
It will adjust memory allocation - all records
and entries are retained after soft reset but
unsaved data or files may be lost.
When an unexpected error cannot be solved with SOFT RESET,
perform CLEANBOOTto restart the system.
It will erase all data stored in the device except in Flash Disk and return
to its default settings.
▪Press the RESETBUTTON briefly.
Follow below steps to CLEANBOOT. (+ or +)
▪Press the POWERBUTTON more than 10 seconds.
▪Press and hold the <RIGHT NAVIGATION> button then press the
POWER button briefly.
▪When Boot Menu will be displayed on the screen, press “3” to
proceed CLEANBOOT.
SOFT RESET
CLEAN BOOT
RESET

05
USIM Card Installation
▪Remove the battery from the battery pack.
▪Insert the USIM Card as shown in the below picture.
▪Insert the battery back to original position and lock by sliding the lock
to secure position
▪Check whether it is installed properly.
Micro SD Card Installation
▪Open the memory card cover.
▪Insert the Micro SD Card as shown in
the left picture.
▪Close the memory card cover back
and check whether it is installed
properly.
CARD INSTALLATION
DEVICE SETUP
User Manual

06
Inserting Battery
▪Open battery cover by sliding the lock to the right.
▪Insert the battery pack.
▪Securely lock the battery cover by sliding the lock to the left.
Removing Battery
▪Loose the battery cover by sliding the lock to the right.
▪Pull up the battery using the ribbon.
▪Fasten the battery cover by sliding the lock to the left.
BATTERY
DEVICE SETUP
▪
▪
※Warning
Risk of Explosion if battery is replaced by an incorrect type. Dispose of
used batteries according to the instructions.
Battery contact pin can break if battery is forcced to insert in wrong
direction. Watch out for the correct direction as indicated on the battery.

07
How to charge
▪ Supply power tothe cradle using the AC
charger.
▪ Insert the PDA to device slot to start
charging the PDA.
Charging status
Charging status of the PDA and the spare
battery is indicated by LEDs.
LED charging indicator on the cradle
indicates the charging status of the spare
battery.
LED on upper left corner in the middle of
the device indicates the charging status of
the battery attached tothe PDA.
Charging with cradle
Charging with snap-on
Power port
DEVICE SETUP
▪
※Warning
Risk of Explosion if unautorized power
supply is used.
※Either Cradle or Snap-on will be provided.
CHARGING
LED Color Battery Status
RED The battery is being
charged.
The battery is fully
charged.
GREEN

08
DATA CAPTURE
Scanning
▪Launch the Scanner program (either ScanEmul or M3ScanTest).
▪Press the SCAN BUTTON toward barcode to read.
Imaging
▪Launch the Scanner program.
▪Press the SCAN BUTTON toward barcode to read.
Make sure the laser beam covered whole barcode to read data properly.
Make sure the laser beam covered whole barcode to read data properly.
SCANNER
※Warning
LASER LIGHT - Do not stare into beam, CLASS 2 LASERPRODUCT
1.0mW, MAX OUTPUT:650nM

09
DATA CAPTURE
Taking pictures
▪Run the Camera program.
▪Tab the Capture button totake a picture.
▪Taken pictures can be checked in the following folder.
For Windows Embedded Handheld: Start\Programs\Pictures&Videos
For Windows Embedded CE: \Flash Disk\Camera\Photo
Taking videos
▪Run the Camera program.
▪Tab the Video Mode button totake a video.
▪Taken videos are stored in Pictures&Videos folder.
For Windows Embedded Handheld: Start\Programs\Pictures&Videos
Video feature is not supported in Windows Embedded CE
CAMERA
※Warning
It may cause significant damage to your eyes if you directly look the flash
attached at camera module.

010
SERVICES AND SUPPORT
Should you require and services or technical support on M3 Mobile’s
product, contact your supplier or visit
M3 Information & Technology Center webpage on:
http://itc.m3mobile.net
After your enquiry is registered on the page, our professional engineer
will reply to you within 24 hours in during the week.
For DOA or RMA, please send the defective product to suitable address
AFTER consulting the supplier.
Please download the ActiveSync from Microsoft webpage to
activesync with PC.
ActiveSync :
http://www.microsoft.com/downloads/en/details.
aspx?FamilyID=9e641c34-6f7f-404d-a04b-dc09f8141141
Windows Mobile Device Center (Windows Vista and 7) :
http://www.microsoft.com/windowsphone/en-us/howto/wp6/sync/
installing-wmdc.aspx
SYNCHRONIZE with YOUR PC
TECHNICAL SUPPORT

Headquarter/Service Center Production Center
M3 bldg., 735-45,
Yeoksam-Dong, Gangnam-gu,
Seoul, 135-080, Korea
Tel: [phone] (Ext.4)
Fax: [phone]
www.m3mobile.net
[email protected]
Chun-ui Techno Park 201-610,
202, Chunui-Dong, Wonmi-Gu,
Bucheon, Gyunggi-Do,
420-857, Korea
Tel: [phone]
Fax: [phone]
Copyright©2013 M3 Mobile Co., Ltd. All Rights Reserved.