M3 Mobile MM3 Installation guide

www.m3mobile.co.kr
MM3 Quick Manual
Ver.1.2

01
PACKAGE
• Please check all items below are included in package box.
< MM3 >
< Adaptor >
< Cradle >
< USB cable >
< Battery >
< Stylus pen >
※Warning
Use of controls or adjustments or performance of procedures other
than those specified herein may result in hazardous radiation exposure.

02
FEATURES
< 1D Scanner > < 2D Imager > < Long-Range Scanner >
Barcode Scan Window
LCD Touch Screen
Camera
Flash
Pistol Grip
Conductor
Speaker
HSDPA LED
Scanner LED
Charging LED
Battery Lock
Scanner Button
Battery
Keypad
Reset Button
IO Port
DEVICE

03
FEATURES
MM3 has four types of keypad – 41keys, 55keys, 5250 and 3270/VT.
Some function keys may not work depending on its options.
< 41 keys >
< 55 keys >
Soft 1
Backlight toggle
Green function
Soft 1
SCAN
SCAN
Soft 2
F keys (F1-F10)
Back Space
Numbers
Back Space
Backlight toggle
Enter
Green function Yellow function
Space
Power
Enter
Space
Characters
Reset
Soft 2
Yellow function
Power
Reset
Numbers
KEYPAD

04
Home CLR
BKSP
DUP
PA1 PA2 PA3
FLD MRK
Tab
ENTER
.
& * ( )
$%^{Vol+
! @ #}Vol-
NL
BRK Help
Reset
DO
< > ~
|
‘?
: ;
+ - *
/ =
< 3270/VT >
< 5250 >
FEATURES
KEYPAD
SCAN
SCAN
Backlight toggle
Backlight toggle
Green function
Green function
Soft 1
Soft 1
Back Space
Back Space
Numbers /
5250 functions
Numbers /
3270/VT functions
Power
Power
FIELD EXIT
Space
Space
Characters /
F keys (F1-F24)
Characters /
F keys (F1-F24)
Reset
Reset
Soft 2
Soft 2
Yellow function
Yellow function

05
When an unexpected error occurs while using
the device, SOFT RESET allows your device to
restart, similar to rebooting a computer.
It will adjust memory allocation - all records and
entries are retained after soft reset but unsaved
data or files may be lost.
When an unexpected error cannot be solved with SOFT RESET,
perform CLEAN BOOT to restart the system.
It will erase all data stored in the device except in Flash Disk and return
to its default settings.
▪Press the RESET BUTTON briefly.
Follow below steps to CLEAN BOOT. ( + + )
▪ Press the POWER BUTTON more than 10 seconds.
▪Press and hold the <SEND> and <END> buttons together then
press the POWER button briefly.
▪When “Clean boot” sign will be displayed on the screen, press “1”
to proceed CLEAN BOOT.
SOFT RESET
CLEAN BOOT
RESET

06
SIM Card Installation
▪Remove the battery from the battery pack.
▪ Insert the SIM Card as shown in the below picture.
▪ Insert the battery back to original position and check whether it is
installed properly.
SD Card Installation
▪Remove the battery from the battery pack.
▪ Insert the SD Card as shown in the upper picture.
▪ Insert the battery back to original position and check whether it is
installed properly.
CARD INSTALLATION
DEVICE SETUP
SD Card
SIM Card

07
Inserting Battery
▪Insert the battery to the battery pack position.
▪ Slide the battery lock to the left to lock the battery pack.
Removing Battery
▪Slide the battery lock to the right to unlock the battery pack.
▪ Then remove the battery from the battery position.
BATTERY
DEVICE SETUP
※Warning
Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of
Used Batteries According to the Instructions.

08
How to charge
▪Supply power to the cradle using the AC
charger.
▪ Insert the PDA to device slot to start
charging the PDA.
Charging status
Charging status of the PDA and the
spare battery is indicated by LEDs.
LED charging indicator on the cradle
indicates the charging status of the
spare battery.
LED on right side in the middle of the
device indicates the charging status
of the battery attached to the PDA.
CHARGING
DEVICE SETUP
Battery attached to the PDA LED color Spare battery
The battery is being
charged. RED The spare battery is being charged.
The battery is fully
charged. GREEN The spare battery is fully charged.

09
DATA CAPTURE
Scanning
▪Launch the Scanner program (either ScanEmul or M3ScanTest).
▪Press the SCAN BUTTON toward barcode to read.
Imaging
▪Launch the Scanner program.
▪Press the SCAN BUTTON toward barcode to read.
Make sure the laser beam covered whole barcode to read data properly.
Make sure the laser beam covered whole barcode to read data properly.
SCANNER
※Warning
LASER LIGHT - Do not stare into beam, CLASS 2 LASER PRODUCT
1.0mW, MAX OUTPUT:650nM