Madeleine Home MH-TB-811 User manual

estimated
installation time
20 : 00
people required
1 or more
MH-TB-811, 811GR
1

Ok, let’s
get started!
Put on mood music!
To prevent damage to product, use the clean side of
package carton or rug as working surface for
assembly.
In the event of missing or damaged parts, delivery
problems etc., please reach out to our team.
We will be happy to x the problem!
2

care guide
Clean regularly with a soft and dry cloth.
To protect nish, avoid use of abrasive cleaners.
Wipe up spills immediately. Please!
While assembling the product,
tighten the bolts up to 50%. Once
all parts are in place, only then
fully tighten the bolts.
3

G
Drawer
1x
H
Medium Shelf
1x
I
Small Shelf
1x
A, C
Shelf Legs
2x
B, D
Shelf Legs
2x
F
Support Rods
1x
E
Support Rods
1x
product
parts
4

(L) - Screw
(M6 x 16mm)
14x
(J) - Flat Washer
(Ø20mm x Ø8.5mm)
14x
(Q)-Screw
6x
(O)- Allen Key
(Ø4mm x Ø110mm)
1x
(M) - Screw
(M6 x 40mm)
4x
(N) - Screw
(M6 x 10mm)
4x
(K) - Lock Washer
(Ø15mm x Ø8mm)
14x
(R)- Metal Brackets
2x
(S)- Screw
(12mm)
4x
(P)- Wall Plug
6x
what’s
included
5

assembly
instructions
Friendly Tip: Take a deep
breath going in. This may be a
tricky part, but nothing too
overwhelming. Just follow
these steps to the T and the
outcome will be
worth it!
6
While assembling the product, tighten the bolts up to 50%.
Once all parts are in place, only then fully tighten the bolts.

Begin assembly by joining the support rods (A, B, C & D) to each
other. A with B and C with D as shown in the image below.
Using the allen key (O), tighten screw (N) on holes in the support
rods as shown below.
step 1:
step 2:
A
B
C
D
7
NO

Now add top and bottom rods (E & F) at the spaces highlighted
below.
Using the allen key (O), tighten screw (M) on holes in the support
rods as shown below. This will x the support rods (E & F) to the
shelf legs.
step 3:
step 4:
8
E
F
M
E & F O

Place small (I) and medium (H) shelves and the drawer (G) at their
respective places. Using the allen key (O), tighten screw (L) &
washers (J & K) on holes in the support rods as shown below.
Assemble the metal brackets (R) in predrilled holes under the
drawers as shown in the image. Use screws (S) to do this.
step 5:
step 6:
G
H
I
9
O
JK
L
G
S

10
installation
instructions
While assembling the product, tighten the bolts up to 50%.
Once all parts are in place, only then fully tighten the bolts.

Next, to install the assembled desk, make marks on the wall with the
help of a pencil where you want to make holes. See the highlighted
areas to understand
Drill holes and insert the wall plugs (P) completely in the wall. Now
insert screws (Q) and tighten using a screwdriver.
step 1:
step 2:
11
PQ

Pull on the ribbon to open the drawer.
Using the allen key (O), detach the handle tted inside the drawer.
step 3:
step 4:
12
O

Place the handle outside the drawer and re-attach using the screws
that you just removed and tighten using the allen key (O).
step 5:
Voila! Your desk is now assembled and secure!
O