MAEN HUDSON 38 User manual

Before being worn for the rst time, or if it has stopped, a MAEN watch must be
wound manually in order to function correctly and precisely. To wind the watch man-
ually, unscrew the winding crown completely, then turn it several times clockwise.
(Turning in the other direction has no effect.) A minimum of 25 turns is required for
adequate partial winding.
The watch will then be wound automatically as long as it is worn on the wrist. Care-
fully screw the crown back down against the case to ensure waterproofness.
Wearing the watch for the rst time
ABOUT THE HUDSON 38 GMT
CERTIFIED SWISS MADE
OVERVIEW
SETTING THE MAEN HUDSON GMT
CARING FOR YOUR HUDSON 38 GMT
WARRANTY
USING YOUR WATCH
USER GUIDE
SERVICE

The Hudson 38 GMT is based on our agship model, the Hudson 38 MK4, and shares
all the improvements of this fourth generation.
With its 30 ATM water resistance, X1 Superluminova, GMT function and screw-down
crown the Hudson GMT is the perfect travel companion.
The Hudson 38 GMT

The Hudson 38 GMT is assembled in La Chaux-de-Fonds, Switzerland. Waterproof
testing, entrance inspection and nal quality control is also performed in Switzerland.
The Swiss Made label is a representation of the ultimate sign of quality - the perfect
combination of function and design.
Certied Swiss Made

Hudson 38 GMT Overview
HOUR HAND
MINUTE HAND
SECONDS HAND
GMT HAND
WINDING CROWN
1
2
3
4
5
1
3
6
2
5
4
DATE WINDOW
6

SCREWED-DOWN POSITION (POSITION 0):
the crown is completely screwed down
against the case. When the crown
is in this position, the Hudson GMT
is guaranteed waterproof to a depth of
30ATM = 300 metres
MANUAL WINDING (POSITION 1):
The crown is unscrewed. To wind the
watch manually, turn the crown
clockwise; turning in the other direction has no
effect.
When setting the watch
for the rst time or after the watch
has stopped, complete a minimum of
25 turns for partial winding.
Setting your Hudson 38 GMT
0 1 2 3
UNSCREW THEN PULL OUT

SETTING THE DATE (POSITION 2):
the crown is unscrewed and pulled out
to the rst notch. To set the date, turn the
crown counter clockwise. To set the GMT hand
turn the crown clockwise.
SETTING THE TIME (POSITION 3):
the crown is unscrewed and pulled out to the
second notch. The seconds hand is stopped,
allowing you to set the time to the precise
second. To set the hour and minute, turn the
crown in either direction. To avoid confusion
between a.m. and p.m. hours, move the hour
hand to 12 o’clock. If the date changes, it is
midnight.
Setting the date & GMT hand
0 1 2 3
UNSCREW THEN PULL OUT

You can help preserve its lustre by cleaning it occasionally with a microbre cloth.
You can also wash the case and bracelet from time to time using soapy water and
a soft brush.
After wearing your watch in the sea, it is important to rinse it with fresh water to
remove any salt and sand deposits. Before cleaning your watch, always ensure that
the crown is screwed down properly against the case to guarantee waterproofness.
Caring for you Hudson 38 GMT
Warranty term: Two year from the date of purchase. This warranty covers manufacturing defects on the watch
itself (movement, case, crystal). Other parts than the above are not covered by this warranty. To have replacement
covered under this warranty performed, please use our contact form on the “contact us” page. In the e-mail you
need to specify your name, address, order number and a detailed description of the issue at hand. Finally, write
‘reclaim of purchase’ as subject of the e-mail and mail. Note that repair/replacements will be charged in the fol-
lowing cases, even during the warranty term.
• Failure or damage caused by improper use or carelessness (knocks, dents, crushing, broken crystal, etc.)
• Failure or damage caused by unjustiable repair or modication
• Failure or damage caused by re or water, or a natural disaster such as for example an earthquake
• Esthetic changes that occur during normal wear and tear and aging (minor scratches, etc.; on the case and/
or cystal, alteration of the colour on the wristband and the peeling of the plating)
• In case the retail store and the purchase date are not indicated on the warranty, or if this information has
been rewritten
The case, dial, hands, crystal, watchband or other parts thereof may be replaced with substitutes if the originals
are not available. This warranty warrants that you can receive free replacement in accordance with the terms set
forth herein and within the specied term, and shall not restrict any lawful right of the Customer.
Any damage caused due to the modication of the watch is not covered by our warranty. Only if the modication
is arranged and executed directly via our service center the original warranty will be maintained.

WWW.MAENWATCHES.COM