MAG SLB220 User manual

© 2020 MAG SLB220
QUICK GUIDE
21 Feb 2020, V1
SLB220 Sliding Barrier
Technical Specification
Power
AC220±10%V, 50Hz
Voltage
DC24V
Motor
Brushless DC motor
Working Temperature
-20℃~ 60℃
Relative Humidity
≤ 90%, no condensation
Open Signal
Passive signals (dry contact)
Communication
RS485
Pass rate
≤30 person/min
Passage Width
550mm
Wing Panel
10mm thick tempered glass
Dimension
Installation

© 2020 MAG SLB220
Connection
1. Connect AC220V power cable to the MCB.
2. Connect dry contact signal from card reader to terminal “Enter“, “GND“ and “Exit“ on the main board.
3. Connect driver and synchronize cables between master and slave as below:
Menu Setting - Enter setting mode by press and hold the “Enter“ button for 3s.
Description
Remark
1. Parameter
1.1 Counter
Display pass through count. (both way)
1.2 Gate Mode
Set gate mode of enter and exit:
1. NC both Rej 2. NC both Free 3. NC both card (default) 4. NC card Free
5. NC card Rej 6. NC Free card 7. NC Free Rej 8. NC Rej Free
9. NC Rej card 10. NO both Free 11. NO both card 12. NO card Free
13. NO Free card
1.3 Pass Timeout
Set maximum waiting time 10-255, unit 0.1s (default is 5 seconds)
1.4 Memory
Set scan card with memory mode
0. Both disable (default), 1. Entry allow, 2. Exit allow, 3. Both allow
1.5 Read In Lane
Set to allow card scanning when user standing in the lane. 1. Not allow (default), 2. Allow
1.6 Open Delay
Set door open delay time 0-255, unit 0.1s (default is 0)
1.7 CLS Delay
Set door close delay time after user has walked through the lane, unit 0.1s (default is 0)
1.8 Rebound Time
Rebound time = Time of door rebound when it is blocked during closing (30-250),
(default 100) [higher value, slower movement]
1.9 Action Time
Action time = Time of door open/close. (30-250), (default 100) [higher value, slower movement]
1.10 Pass End
Set end position IR sensor function (Do not modify) 1. Exit (default), 2. Safety
1.11 Intrude Set
Set intrude alarm mode. 1. No alarm, 2. Alarm, 3. Alarm and close (default)
1.12 Reverse Set
Set reverse alarm mode. 1. No alarm, 2. Alarm, 3. Alarm and close (default)
1.13 Tail-Gating
Set Tail-Gating alarm mode. 1. No alarm, 2. Alarm, 3. Alarm and close (default)
1.14 Adv. Param.
Advance parameter setting (Only for professional engineer level)
2. System Set
2.1 Language
Set menu display language 1. English (default) 2. Chinese
2.2 Device Type
Display Controller Device Type
2.3 Version
Display hardware and firmware version
Single lane connection
Multiple lanes connection

© 2020 MAG SLB220
2.4 Set Address
Set Device Logic address (do not modify)
2.5 RS485 Baud
Set the baud rate of the RS485 (default is 9600)
2.6 Reset
Reset all setting to factory default
2.7 Restart
Restart controller
3. Factory Test
Only for professional engineer level
© COPYRIGHT 2020.This documentation served as a reference only. It is subject to change without further notice. All
the diagrams and information in this documentation may not be duplicated or modified in any form without the written
approval from the management.