MAGNITUDE LIGHTING E Series User manual

INSTALLATION GUIDE
E-SERIES
120VAC / 12VDC
Magnitude, Inc. Page 1of 2
14711 Bentley Circle. Tustin, CA 92780 www.MagnitudeInc.com [email protected] DOC-GU-00002A Rev. 1
109 Ref.
2
7
5
4
1
8
6
3
06
2
2
02
000F22
2
2
A3
06
THE INFORMATION ON THIS DRAWING IS PROPRIETARY. THE INFORMATION SHALL NOT BE DISCLOSED, REPRODUCED IN ANY FORM OR USED FOR ANY PURPOSE, WITHOUT PRIOR WRITTEN CONSENT OF MAGNITUDE INC.
109 Ref.
2
7
5
4
1
8
6
3
06
2
2
02
000F22
2
2
A3
06
THE INFORMATION ON THIS DRAWING IS PROPRIETARY. THE INFORMATION SHALL NOT BE DISCLOSED, REPRODUCED IN ANY FORM OR USED FOR ANY PURPOSE, WITHOUT PRIOR WRITTEN CONSENT OF MAGNITUDE INC.
General
This driver is to be installed in accordance with Article 450 of the
National Electric Code. The driver must be installed in a well-ventilated
area free from explosive gases and vapors. Proper operation requires
for free flow of air. This driver should only be installed by a qualied
electrician.
Precautions Before Installing
Check the label and ensure the driver has the proper input voltage and
wattage for the job. Check the wire markings to ensure they match the
wiring diagram on this installation guide.
Quick Specs
Input Voltage 120V AC
Output Voltage 12V DC
Max. Ambient Temp. -300C to 400C (-22°F - 104°F)
Enclosure IP67 Wet Location
Min. Installation Space
Between Drivers 5” Inch
Mounting
Select a suitable location capable of supporting the weight of the
driver. Use the two key holes in the wire housing and third hold on the
flange when mounting. It is recommended that the driver be mounted
vertically with the wiring compartment pointing down. Recommended
spacing between drivers is 5”.
5” Min.
Spacing
E-SERIES RECOGNIZED
FOR MODELS
E20R12DC, E40R12DC, E60R12DC
Mounting
Holes
Mounting
Holes

INSTALLATION GUIDE
E-SERIES
120VAC / 12VDC
Magnitude, Inc. Page 2of 2
14711 Bentley Circle. Tustin, CA 92780 www.MagnitudeInc.com [email protected] DOC-GU-00002A Rev. 1
With power turned off, route the input
wires through a strain relief and
connect one wire to black and one
wire to white. for all wire connections
use only UL listed wire nuts and
connectors of suitable size and
type. Connect the ground wire to the
transformer green wire.
12
Output
Input
Wire Nuts
(By others)
Output Connections
Bring the wires of the light xture through
the other clamp connector and connect
them to the driver wires - positive to the
red (+ ) wire and negative to blue ( - ) wire.
Measuring the output voltage without a
load will result readings greater than the
nominal voltage.
The transformer case MUST be
grounded in accordance with the N.E.C
Wire nuts or wago connectors by others
Wiring Diagram
INPUT
120V AC 60Hz Dimmer
(Optional)
Green Wire
Ground
Red Wire
Blue Wire
Input Wire (Black)
Input Wire (White)
+
-
We Drive Light
The contents of this document are subject to change without notice
14711 Bentley Circle, Tustin, CA 92780 Tel: [phone] Fax: [phone] www.magnitudeinc.com rev004
MAGNITUDE
LIGHTING
Wiring Diagram
INPUT
120V AC 60Hz Dimmer
(Optional)
Green Wire
Ground
Red Wire
Purple Wire
Input Wire (Black)
Input Wire (White)
OUTPUT
24V DC
+
-
We Drive Light
The contents of this document are subject to change without notice
14711 Bentley Circle, Tustin, CA 92780 Tel: [phone] Fax: [phone] www.magnitudeinc.com rev004
MAGNITUDE
LIGHTING
Wiring Diagram
Do not install PWM low voltage
controllers on the output without
consulting with Magnitude Inc.
Dimming
Dimmable with any standard MLV / Incandescent
TRIAC (Leading edge) dimmer switch. Dimmer switch
is to be installed on the input (120VAC side) of the
driver. For smooth dimming, 8W minimum load is
required. Please visit our website for a full dimmer
compatibility list www.magnitudeinc.com
Wiring Diagram
INPUT
120V AC 60Hz Dimmer
(Optional)
Green Wire
Ground
Red Wire
Blue Wire
Input Wire (black)
Input Wire (white)
OUTPUT
12V DC
+
-
We Drive Light
The contents of this document are subject to change without notice
14711 Bentley Circle, Tustin, CA 92780 Tel: [phone] Fax: [phone] www.magnitudeinc.com rev002
MAGNITUDE
LIGHTING
Wiring Diagram
INPUT
120V AC 60Hz Dimmer
(Optional)
Green Wire
Ground
Red Wire
Blue Wire
Input Wire (black)
Input Wire (white)
OUTPUT
12V DC
+
-
We Drive Light
The contents of this document are subject to change without notice
14711 Bentley Circle, Tustin, CA 92780 Tel: [phone] Fax: [phone] www.magnitudeinc.com rev002
MAGNITUDE
LIGHTING
Green
Black
White
Blue
Red