Maintronic Casambi CBA UP User manual

CBA UP
Casambi blind actuator
Valid from version:
(H=Hardware | F=Firmware)
10.750 - CBA UP H2 | F2.5
10.752 - CBA UP H1 | F2.5
10752_MA_en_A4_CBA-UP_20210310
Manual EN
EN

Manual english Casambi blind actuator
2
1. General informaon 3
1.1 About this Document 3
1.2 Service and contact 3
1.3 Legals 3
1.4 Symbol explanaon 4
2. Safety informaon 5
3. Product descripon 6
3.1 Intended Use 6
3.2 Funcons 6
3.4 Operang notes 7
3.3 Installaon and dimensions 8
3.5 Connecons and elements 9
4. Commissioning 10
4.1 Update rmware 10
4.2 Choose applicaon proles 10
4.3 Select prole and learn into a network 11
4.3.1 Prole A: CBA Blind
Drive blind | Adjust slats 12
4.3.2 Prole B: CBA Blind + Buons
Drive blind | Adjust slats | addional switches 13
4.3.3 Prole C: CBA Shuer
Roller blind drive 14
4.3.4 Prol D: CBA Shuer + Buons
Roller blind drive | Operaon addional switches 15
4.3.5 Prol E: CBA Buons
Roller blind drive | with buom operaon elements in App 16
4.4 Calibraon 17
5. Operaon 18
5.1 Operaon with device buon 18
5.2 Operaon with pushbuon input T1 / T2 (only 10.752) 18
5.3 Push Buon mode 18
5.4 Congure pushbuon inputs 19
5.5 Operaon with pushbuon over L‘ release phase 20
Table of contents

www.maintronic.de 3
1. General informaon
1.3 Legals
The division building automaon and all associ-
ated products are products of MTC maintronic®
GmbH (hereaer maintronic). All rights reserved,
as well as mistakes and typing errors.
The trademarks and trade names menoned in
this document are the property of their respec-
ve owners.
The content in this document is for product infor-
maon purposes only. Product features may vary
during connuous product development and may
change at any me without noce.
maintronic assumes no liability or warranty regar-
ding this document or the products described.
1.1 About this Document
Congratulaons and thank you for choosing this
maintronic product and the trust you have placed
in us. We, the team of maintronic, wish you a lot
of fun with this product.
Due to connuous product development, some of
the informaon may not be complete and up-to-
date.
The informaon in this document is subject to
change without prior noce. Please check our
website www.maintronic.de, if there is a newer
version.
1.2 Service and contact
You can nd informaon, onlinehelp as well as
downloads for the product on our website. Con-
tact us if you have any problems or quesons
about your device.

Manual english Casambi blind actuator
4
1.4 Symbol explanaon
CAUTION
The signal word „CAUTION“ indicates a possibly imminent danger. If it is not avoided, slight
or minor injuries may result.
ATTENTION
The signal word „ATTENTION“ indicates a situaon that can lead to material damage. Either
to the product itself or to other objects in the environment.
WARNING
The signal word „WARNING“ indicates a possibly imminent danger. If it is not avoided, death
or very serious injuries may result.
DANGER
The signal word „DANGER“ indicates an imminent danger. If not avoided, death or serious
injury will result.
NOTE
The signal word „NOTE“ indicates ps and recommendaons to help you get the most out of
the product.

www.maintronic.de 5
WARNING
For your own safety, read all instrucons and in-
formaon in this manual carefully before inial
operaon. Keep this manual for future reference.
The instrucons are an integral part of the pro-
duct and must be handed to the end customer.
All informaon and instrucons in this manual
must be observed completely and in detail. The
manufactuer is not responsible for any direct or
consequenal damage that results from disregar-
ding any informaon in this manual.
Waste disposal
In accordance with European Direcve 2002/96/
EC (it`s) not longer usable electronic devices and
defecve or used baeries (European Direcve
2006/66EG) must collected separately and dispo-
sed by an environmentally sound recycling.
This symbol indicates that electrical and elect-
ronic equipment must be disposed of separately
from normal waste at the end of its operaonal
lifeme.
Should these product are no longer be useable,
the user is required by law to dispose of old ap-
pliances separately from their household waste e.
g. at a local authority collecon point or recycling
center.
CE-marking
The devices comply with the EU direcves appli-
cable at the me they are placed on the market.
DANGER
The unit must only be installed and serviced by a
proven electrican specialist, in accordance of all
relevant regulaons, safety and accident preven-
on direcves of the country.
Be sure that the exisng mains voltage corres-
ponds with the specied operang voltage befo-
re operang the device.
Risk of electric shock. Do not operate the device
without a cover. Even when switched o, voltage
may be present at the outputs. When working on
the device or connected loads, always disconnect
the upstream fuse from the power supply.
Apply the „Five Safety Rules“
(DIN VDE 0105, EN 50110):
1. Disconnect
2. Secure against being switched on again
3. Determine absence of voltage
4. Ground and short circuit
5. Cover or isolate nearby live parts
Only install the device in places with a good
venlaon and without humidity or high tempe-
ratures. Do not expose the unit to rain or snow.
Do not operate the unit near heat sources, e.g.
radiators.
If any of the following occurs, do not operate the
device without rst checking it:
• if objects have fallen or liquid has been
spilled into the unit.
• if the device has been exposed to rain.
• if the device does not operate normally or
with altered characteriscs.
• if the device has been dropped or has a bro-
ken housing.
For cleaning only use a dry, so cloth, by no me-
ans liquids.
2. Safety informaon

Manual english Casambi blind actuator
6
3. Product descripon
3.1 Intended Use
Casambi blind actuator for control of blind, shut-
ter, gate, or awning motors. Control by Casambi
Bluetooth via APP or local control using standard
blind pushbuons.
Product Item.No. Type of relay Construcon
CBA UP 10.750
EOL
2 CH Changeover Flush-mounted
housing (UP)
CBA UP 10.752 2 CH Changeover;
2 pushbuon
inputs
Flush-mounted
housing (UP)
Item 10.752 - CBA UP has 2 addional key inputs
compared to the 10.750 all other funcons are
idencal.
16A
Changeover
100..240V
70 g
0...+50°C
As soon as the device is added to your network,
it can be operated. Groups can be formed, scenes
and mers can be created.
These funcons allow e.g. to group 5 blinds on one
side of a building and to operate them together.
In addion, automated up and down movements
can be programmed as a me-controlled scene.
If you need help with conguraon and opera-
on of Casambi please refer to the ocial Casambi
help at: hps://support.casambi.com
• For indoor use only
• Flush mount housing for installaon in junc-
on, cavity or switch boxes.
3.2 Funcons
The blind actuator CBA UP Casambi has a Blu-
etooth Casambi interface and can be opera-
ted via smartphone with the Casambi APP.
Casambi App automacally idenes the device
and can be integrated into exisng networks.
The device has dierent operang modes
(so-called Casambi proles) with the pro-
les the funconality and the parameters are
determined. Casambi prole must be selec-
ted in the Casambi APP when pairing a device
in order to select a specic operang mode.

Manual english Casambi blind actuator
7
Group
Single
Group
Single
5%
Slat angle
85 %
Hori ontal positionz
0% (open)
60 %
100% (closed)
85%
60 %
3.4 Operang notes
There are dierent methods to operate the blind
actuator.
Driving over driving me
In the case of driving over the driving me, a sin-
gle impulse (e.g. pressing a buon or starng a
me-controlled scene) triggers the blind/shuer
etc. to move once to the zero point(OT) 0% or end
point(UT) 100%.
This driving me is stored in the parameters of
the actuator once and then recalled (see 4.4).
Driving to an absolute posion
With a drive to an absolute posion, any hori-
zontal posion can be approached. The absolute
posion is controlled by a slider (from OT 0% to
UT 100%), which determines the posion of the
connected blind / shuer, etc..
Slat adjustment
A slider can be used to adjust the angle of the slats
for venean blinds. Furthermore, the slat posion
is stored when moving to an absolute posion and
the set value is automacally readjusted aer re-
aching the driving posion.
For example, if the blind shall be moved down
only a lile bit and the slats are set to 5%. Then
aer reaching the target posion, the slats are set
to 5% again.

www.maintronic.de 8
30 mm
55 mm
3.3 Installaon and dimensions
Even though the device has very compact dimen-
sions, it is strongly recommended to use the dee-
pest juncon boxes possible.
Depending on which pushbuon aachments are
used, up to 30 mm of addional installaon space
is required.
For installaon in cavity or switch boxes, the side
aps have to be removed. Install the device with
the labeling, LED and device buons facing for-
wards.
removeable flaps

Manual english Casambi blind actuator
9
3.5 Connecons and elements
1Devicebuon
2Status-LED
8mm
0,5...1,5mm² starr | single wire
0,5...1,5mm² exibel | ne wire
0,5...0,75mm² exibel mit Aderendhülse | ne wire with ferrule
Figure: CBA UP - 10.750
Figure: CBA UP - 10.752
NOTE
The relay outputs are mutually locked
to ensure that only one drive path is
acve at a me (motor protecon).
1 N Neutral conductor 4Relay up
2 N Neutral conductor 5Relay down
3 L Input Voltage 230V AC 6L‘ Release phase for
standard blind buon
7T1 Pushbuon input 1 8T2 Pushbuon input 2
Pushbuon inputs T1 / T2 only item no.: 10.752

www.maintronic.de 10
4. Commissioning
To make sure that the funconality of the device
is up to date, rst of all you have to check if a new
rmware is available.
4.1 Update rmware
1. Go to nearby devices
2. Scroll down
3. Check for updates
4. If an update is available, please install
4.2 Choose applicaon proles
The device has dierent operang modes (so-
called Casambi proles) with the proles the
funconality and the parameters are determined.
Before programming, a Casambi prole must be
selected (by default, the prole - CBA Blind + But-
tons is set).
Proles for venian blinds
CBA Blind • Operaon via APP
• Move blind to absolute posion
• Adjust slat angle
CBA Blind
+ Buons
• Move blind to absolute posion
• Adjust slat angle
• Addional controls for acvaon
via external pushbuons or scenes
Proles for roller blind
CBA Shuer • Operaon via APP
• Move roller blind to absolute posion
CBA Shuer
+ Buons
• Move roller blind to absolute posion
• Addional controls for acvaon
via external pushbuons or scenes
Select a suitable prole for your applicaon on
the following pages.

www.maintronic.de 11
4.3 Select prole and learn into a network
If you have selected a suitable prole for your ap-
plicaon from the following pages, the device will
be added to a Casambi network.
Tap on the menu item „Change
prole)
Tap on the menu item
„Add to ... Network“
The selected prole is now
loaded
Select the desired operang
mode (prole)
Device must be unpaired
Aer the prole selecon ...
Start update

Manual english Casambi blind actuator
12
4.3.1 Prole A: CBA Blind
Drive blind | Adjust slats
Operang elements in the APP Informaons and parameterProle view in the APP
Prole parameter
Parameter Casambi Descripon parameter Value Default | Notes
Drive Time Drive me for blind operaon 0 … 255s (seconds) 60s default
Angle Time Drive me for slat adjustment 0 ... 65535ms (milliseconds) 2000ms default
Swap Controls Up/
Down
Logical invert of drive direcon No | Yes Reverse driving direcon
Push Buon mode Behavior of the pushbuon inputs Descripon see 5.3
Casambi prole name Fixture Id Control element name Funcon Control element type
CBA Blind 17801 Posion Posion Slider (0% - 100%)
Angle Slat angle Slider (0% - 100%)

www.maintronic.de 13
4.3.2 Prole B: CBA Blind + Buons
Drive blind | Adjust slats | addional switches
Casambi prole name Fixture Id Control element name Funcon Control element type
CBA Blind + Buons 17802 Posion Posion Slider (0% - 100%)
Angle Slat angle Slider (0% - 100%)
Up Single drive Up ON/OFF Toggle
Down Single drive Down ON/OFF Toggle
Angle Slat angle Push Buon
Prole parameter
Parameter Casambi Descripon parameter Value Default | Notes
Drive Time Drive me for blind operaon 0 … 255s (seconds) 60s default
Angle Time Drive me for slat adjustment 0 ... 65535ms (milliseconds) 2000ms default
Swap Controls Up/
Down
Logical invert of drive direcon No | Yes Reverse driving direcon
Push Buon mode Behavior of the pushbuon inputs Descripon see 5.3
Operang elements in the APP Informaons and parameterProle view in the APP

Manual english Casambi blind actuator
14
4.3.3 Prole C: CBA Shuer
Roller blind drive
Casambi prole name Fixture Id Control element name Funcon Control element type
CBA Shuer 17803 Posion Posion Slider (0% - 100%)
Prol Parameter
Parameter Casambi Descripon parameter Value Default | Notes
Drive Time Drive me for roller blind 0 … 255s (soconds) 60s Default
Swap Controls Up/
Down
Logical invert of drive direcon No | Yes Reverse driving direcon
Push Buon mode Behavior of the pushbuon inputs Descripon see 5.3
Operang elements in the APP Informaons and parameterProle view in the APP

www.maintronic.de 15
4.3.4 Prol D: CBA Shuer + Buons
Roller blind drive | Operaon addional switches
Casambi prole name Fixture Id Control element name Funcon Control element type
CBA Shuer + Buons 17804 Posion Posion Slider (0% - 100%)
Up Single drive Up ON/OFF Toggle
Down Single drive Down ON/OFF Toggle
Prol parameter
Parameter Casambi Descripon parameter Value Default | Notes
Drive Time Drive me for roller blind operaon 0 … 255s (seconds) 60s default
Swap Controls Up/
Down
Logical invert of drive direcon No | Yes Reverse driving direcon
Push Buon mode Behavior of the pushbuon inputs Descripon see 5.3
Operang elements in the APP Informaons and parameterProle view in the APP

Manual english Casambi blind actuator
16
4.3.5 Prol E: CBA Buons
Roller blind drive | with buom operaon elements in App
Casambi prole name Fixture Id Control element name Funcon Control element type
CBA Buons 14343 Up Single drive Up ON/OFF Toggle
Down Single drive Down ON/OFF Toggle
Funcon A Funcon for buon A Push Buon
Funcon B Funcon for buon B Push Buon
Prole parameter
Parameter Casambi Descripon parameter Value Default | Notes
Drive Time Drive me for roller blind operaon 0 … 255s (seconds) 60s default
Funcon A
Funcon B
Funcon for buon A
Funcon for buon B
Not in Use Not in Use
Blind Up Roller blind ▲ Up
Blind Down Roller blind ▼ Down
Toggle direcon ▲.. Stop .. ▼ .. Stop
Change direcon
Blind Up with Time Rollo ▲ up with me
Blind Down with Time Rollo ▼ down with me
Toggle direcon with Time ▲ (t) Stop .. ▼ (t) Stop
Reverse direcon by me
Swap Controls Up/
Down
Logical invert of drive direcon No | Yes Reverse driving direcon
Push Buon mode Behavior of the pushbuon inputs Descripon see 5.3
Operang elements in the APP Informaons and parameterProle view in the APP

Manual english Casambi blind actuator
17
4.4 Calibraon
Once the device is added into a Casambi network,
a calibraon can be performed..
Perform calibraon drive (Drive me)
To ensure proper operaon, a calibraon drive
must be performed during inial startup.
1. Therefore, run a complete cycle (0% fully open
to 100% fully closed) and measure the drive
me.
2. In order to take into eect deviaons in the
travel me from boom to top, the cycle
(from 100% completely closed to 0% comple-
tely open) can be measured again.
3. Enter the measured me plus approx. 1 se-
cond (as a buer) in the device sengs under
parameter „Drive Time“.
Seng the slat posion (Angle me)
The „Angle Time“ is the aperture angle of the
blind slats, this me must be measured and set in
the parameters
1. Move the blind up a lile unl the slats are in
a horizontal posion.
2. Now move the blind downwards and stop the
me unl the slats are closed.
3. Set the measured me in ms in the parame-
ters under „Angle Time“.
Set drive direcon
If the drive direcon is not correct, the parameter
„Swap Controls Up/Down“ can be used to swap
the direcon.

www.maintronic.de 18
5. Operaon
5.1 Operaon with device buon
The device buon 1 has the same priority as the Casambi APP, the last one wins.
Funcon device buon Keystroke
Switching paern LED
Relais UP green
Relais STOP o
Relais DOWN red
Relais STOP o
Short press
5.2 Operaon with pushbuon input T1 / T2 (only 10.752)
The funconality of the push buon inputs is de-
ned by a parameter. Before the buon inputs are
congured, a push buon mode must be selected.
5.3 Push Buon mode
In order to change the Push Buon mode, pro-
ceed as shown on the right.
Push Buon mode - Possible parameters
Casambi Standard Casambi Push buon input
Buon Funcon as push buon - push=acve; release=o
Buon command processing internally in MTC controller
Group Buon Funcon as group buon - push=on; release=o
If several blind actuators are combined as a group, one device of the group must be dened as the master. For
the desired master, the push buon style must be set to Group Buon.
The other maintronic devices in the group are automacally slaves and the funcon of the master takes place.
Switch Funcon as a switch - 1x push = on - 1x push = o)
release is ignored
Group Switch Funcon as a group switch - 1x push = on - 1x push = o
If several blind actuators are combined as a group, one device of the group must be dened as the master. For
the desired master, the push buon style must be set to Group Switch.
The other maintronic devices in the group are automacally slaves and the funcon of the master takes place.
Enabled with 2 programmable inputs, local con-
trol is so much easier. These inputs can used as
a direct precongured Up-Down pushbuon or
control any casambi enabled device over Casambi
input control. It‘s just a change of an parameter in
the app.
1. Open Casambi app
2. Double tap on the device
3. Scroll to the item parameter
4. Tap on Push Buon mode
5. Select parameters
(See the list below)

Manual english Casambi blind actuator
19
5.4 Congure pushbuon inputs
Pushbuon inputs can be individually assigned with desired funcons.
In order to do this, the following steps are necessary:
1. Open Casambi app and tap on „... More“
2. Open item „Switch“
3. Select device
4. For example program switch with single funcon
a) Select not acve
b) Select not acve
c) Select controls an element
d) Select element
e) Select CBA Buons UP

www.maintronic.de 20
5.5 Operaon with pushbuon over L‘ release phase
Pin 6 (L’) is an release phase
to where an external blind pushbuon
can be connected.
WARNING
Please note that the pin for enabling phase L‘ (pin 6) is always connected to the mains vol-
tage as long as no acve movement is being performed via the Casambi control level.
NOTE
All movements via the „L‘ path“ control are not detected by Casambi. If you use proles
A,B,C or D, the indicaon of the horizontal posion is no longer correct. Only a travel to one
of the end points (OT/UT) via the control from Casambi „synchronizes“ the display with the
real posion again.
As soon as a travel command or an automaon object is sent, the manual travel is inter-
rupted. If the device is operated in automated mode, the key inputs T1 and T2 (only 10.752)
must be used.
ATTENTION
Only pushbuons without latching funcon and no switches may be connected.
The motor can be destroyed if this is not observed.
Carl-Zeiss-Str. 10-14
97424 Schweinfurt / Germany
Tel. [phone]
Fax. [phone]
www.maintronic.de
inf[email protected]