Maintronic DASPip INS User manual

1
Power PWM Actuator 1CH
DASPip INS
Quick guide
Gülg für folgende Versionen:
(H=Hardware F=Firmware)
10.712 - DASPip INS H 2 F 1.5.0
10.772 - DASPip UP H 1 F 1.5.0
DASPip_10712_10772_Manual_EN
Dokument Datum: 10.07.2018
2
1. Safety instrucons
For your own safety, read all instrucons and informaon in
this manual carefully before inial operaon.
Keep this manual for future reference.
• The instrucons are an integral part of the product and
must be handed to the end customer.
• All informaon and instrucons in this manual must be ob-
served completely and in detail. The manufacturer is not
responsible for any direct or consequenal damage that
results from disregarding any informaon in this manual.
• Electrical equipment may only be installed by a qualied
electrician in compliance with the country-specic stan-
dards, guidelines and regulaons.
• Risk of electric shock. Do not operate the device without
a cover. Even when switched o, voltage may be present
at the outputs. When working on the device or connected
loads, always disconnect the upstream fuse from the po-
wer supply.
• Install the device only on places with a good venlaon
and without humidity or high temperatures. Do Not expose
the unit to rain or snow. Do not operate the unit near heat
sources, e.g. radiators.
• Make sure the applied mains voltage matches to the speci-
ed operang voltage before operang the device.
The device may only be used
• as a dimmer for switching and dimming lights
• rmly in a dry and clean environment
• only approved for indoor use
• that access is only possible with tools
• only operate on 1 phase with 230 V AC
• with a backup fuse of max. 16A
3
2. Funcons / Features
• DALI 1CH Power PWM Actuator for LED
• energy saving design through feedforwards relay
• control with DALI or tastDIM (230V touch dimming) (1)
• DALI interface (D1/D2) / own DALI-short adress
• EEG frequency shi compliant
• Protecon circuits for safe operaon
Dimming or switching commands are operated by DALI para-
meters or by pressing a buon (tastDIM).
2.1 Installaon
DASPip INS - Installaon housing for indoor use, for ceiling or
luminaire installaon, in oor ducts or for wall mounng.
DASPip UP - ush mounng

4
2.2 Operang mode 1 „Power PWM“ LED Dimmer
• LEDs on constant voltage power supplies +10...48V DC
• power consumpon max. 3 A
• Dimming range (0; 0,1-100%)
DASP ip INS (Installaon housing)
Connecon with Constant Voltage power supply
5
DASP ip UP (ush mounted)
Connecon with Constant Voltage power supply
6
2.3 Operang mode 2 „Signal PWM“ Control
power supplies with an integrated PWM input
• Converts the brightness values from DALI to PWM.
• For all power supplies with „3-in-2-input“
(0-10V, Po, PWM)
• Output cascadable (1 DASP, several power supplies)
• Dimming range dependent on power supply
(...10-100% | o)
Connecon to dimmer with PWM input

7
Connecon to dimmer with PWM input
8
3. Connecons
Screw terminal for 0.2 ... 2.5 mm² stranded wire
or 0.2 ... 4 mm² single wire
1234
-X1
tast
DIM
L N
120-240 V
DALI 1CH
POWER PWM
ACTUATOR
DALI
D1 D2
DASP
INS
iP
N
NL L´
brown
blue
maintronic.d e
10.712
tc
ta 0-50C°
56
7
8
DASPip INS DASPip UP
N - Neutral conductor 1N - Neutral conductor
N - Neutral conductor 2N - Neutral conductor
L - Mains 230V AC 3L - Mains 230V AC
L´ - Load output (switched phase L´) 4L - Mains 230V AC
D1 - DALI data (alt. tastDIM) 5L - Mains 230V AC
D2 - DALI data (alt. tastDIM) 6L´ - Load output (switched phase L´)
DIMM PWM + (brown wire) 7D1 - DALI data (alt. tastDIM)
DIMM PWM - (blue wire) 8D2 - DALI data (alt. tastDIM)
9DIMM PWM -
10 DIMM PWM +
9
4. DALI general
DALI (Digital Addressable Lighng Interface) is a standardized
digital communicaon interface in the eld of building auto-
maon.
4.1 DALI note
The DALI signal is not SELV (safety extra-low voltage), the ins-
tallaon instrucons for mains voltage apply.
The maximum cable length of the DALI control cable must not
exceed 300m (with 1.5mm² cable cross-secon) or 2V voltage
drop.
4.2 Groups and Scenes
In each DALI circle 16 groups can be formed, with each 16
scenes. A scene includes the brightness value of a short
address.
4.3 DALI device-specic
The device search assigns a DALI short address to the DASPip
INS. Please note the operang instrucons for your DALI con-
troller or gateway.
The module works accordingly to the following regulaons:
IEC 62386-101, General requirements; System
IEC 62386-102, General requirements; Control gear
IEC 62386-207, Parcular requirements for control gear -
LED-modules (device type 6)

10
4.4 DALI-Commands
DALI parameter Value range Factory seng
Power On Level 0 – 100 % (0 – 254) 100 %
Brightness value aer switching on
(DALI Wert 255 = MASK)
System Failure Level 0 – 100 % (0 – 254) 100 %
Brightness value when DALI-Signal Failure
(DALI Wert 255 = MASK)
Min Level 0 – 100 % (0 – 254) 0,8 %
smallest possible brightness value
Max Level 0 – 100 % (0 – 254) 100 %
maximum achievable brightness value
Fade Time von 0 – 90,5 Sekunden < 0,7 S
Speed when changing the brightness value
Fade Rate von 1 – 72 Schrien/s 45 Schrie/s
Steps for changes to the brightness value via
DALI command darker and brighter
4.5 smartGX (=smart Gear Xtensions) *
(*) Extended funcons for DALI operang devices.
- Output characterisc - output calibraon
- PWM-invert - Power-On delay
- Power-O delay - Reverse relay switching state ...
The smartGX funcons can be adjusted with the maintronic
DALI Device Manager soware. This also requires a DALI USB
controller (DALI mouse).
11
5. buon operaon
The module can be operated via tastDIM with 230V at the DALI
input (see tastDIM 230V).
Tastendruck
short press On- / O
Dim the last memory level brightness
long press Dimming
Dimming up and down (start at min level)
2x short press Switch to Max Level
Press for 10 seconds Synchronizaon of the connected devices (see 5.2)
Press for 30 seconds Factory Reset (see 6.7)
4x short press Programming Min-Level (see 5.3)
5.1 tastDIM ** 230V-Pushbuon input
Alternavely, the DALI input can also be used with tastDIM.
tastDIM is a direct 230V AC pushbuon input with long press
funcon. For this purpose, a voltage of 230V AC is connected
to the DALI contact.
A mixed operaon of DALI and tastDIM is not permied.
(**) Buon 230V against N at the DALI input (not SELV)!
Several push buons can be connected parallel.
Several tastDIM-capable devices can be connected to a push-
buon line.
IMPORTANT - When using the DALI input as tastDIM,
no further DALI operang device or DALI controller
may be connected in the same circuit since there is
230V input on the DALI input!
12
5.2 Synchronize several devices on one
tastDIM(Pushbuon input):
If the buon has been pressed for at least 10 seconds, all out-
puts are reset, the connected dimmers go to 50% for signaling.
L
N
< 1s
D1
D2
230VAC
< 1s > 1s
123
> 1s
4

13
5.3 Adjust Min-Level
In some situaons it is necessary to readjust the min level. If no
DALI is available, the Min level can also be set via a 230V Push-
buon connected to the tastDIM *. Perform programming with
the following steps within 15 minutes aer power-on:
4x min-level
1x
> 1s
flash
LED
> 1s
min-level light up
LED
> 2s
LED
1
START
2
PROG
3
SAVE
14
7. Protecon funcons
Short-circuit shutdown
When a short circuit occurs, device automac switch-o. Every
30 seconds is tested whether the short circuit is sll present.
When short circuit is eliminated, device restart automacally.
If the error is sll present aer 5 minutes, device switch o
completely.
Power limitaon at overtemperature
In the event of overtemperature, an automac derang oc-
curs, which means that the dimmer‘s power is throled and
the load is dimming down.
Important!
The connected load is reduced depending on the type of ins-
tallaon:
• Installaon in hollow or wooden walls by 15% as well
• 10% for each 5 ° C exceeds the ambient temperature of
25 ° C
15
8. Aachment
8.1 Excerpt from the technical data
DASP ip INS /
DASP ip UP
PWM output 1 channel - diming range 0...100 %
125 Hz
Max. output current 3A
Ballast-relay
switch, not potenal-free,
switched phase
1 x 16 A/ 230 V AC
Switched phase L´ ü
Power supply 220V-240V AC 50 / 60Hz
Housing mode
Ceiling / installaon housing (DASPip INS)
Licensed under DM/053379 of Tridonic
ush mounted (DASPip UP)
Dimensions DASPip INS: L=101,5 x B=51 x H=29,5 mm
DASPip UP: L=46,5 x B=70 x H=30 mm
IP Code according to
DIN EN 60529 IP20 10mm/5KV
Protecon class II
Temperature
(environment) ta 0° – 50° Celsius
Detailed technical data can be found in the data sheet.

16
8.2 Return
A return form can be found on our homepage. The maintronic
return form is to be completed step by step and with exact
error descripon. The purchase receipt must be aached here.
Our product must be returned packed carefully in a carton..
8.3 Disposal regulaons for EU countries
According to European Direcve 2002/96 / EC, obsolete elec-
trical appliances and defecve or used baeries (European
Direcve 2006/66 / EC) must be collected separately and dis-
posed of by environmentally sound recycling.
Please do not dispose of the product in your household waste!!
8.4 Contacng maintronic
On our website www.maintronic.de you will nd downloads,
instrucons, online help and answers to frequently asked
quesons (FAQ) for the products. Contact us if problems or
quesons arise about your device.
© 2018 - maintronic® GmbH reserve the right to make
technical changes and product improvement
without prior noce. Mistakes and typing
errors reserved. All rights reserved.
MTC maintronic GmbH
Carl-Zeiss-Str. 10-14
D-97424 Schweinfurt/Germany
Phone: [phone]
www.maintronic.de
[email protected]