Majestic 32LCUF-F User manual

For use with a listed gas-fired
unvented decorative room heater
not to exceed 40,000 BTU/hr. Do
Not Build a Wood Fire.
READ AND SAVE THESE INSTRUCTIONS
WARNINGS
If the information in this manual is not followed exactly,


         


– WHAT TO DO IF YOU SMELL GAS
  
• Do not touch any electrical switch; do not use any

  

  

       
       

Lo-RideR
UNVENTED
VENT-FREE FIREBOXES
INSTALLATION AND OPERATING
INSTRUCTIONS
MODELS: 32LCUF-F, 32LCUF-R, 36LCUFC-R
Carefully review the instructions

unvented room heater for the mini-

DO NOT INSTALL AN APPLIANCE
IN THIS FIREBOX UNLESS THIS
FIREBOX MEETS THE MINIMUM
DIMENSIONS REqUIRED FOR
THE INSTALLATION.
WARNINGS
If the information in this manual is not followed
       

 


– WHAT TO DO IF YOU SMELL GAS
  
• Do not touch any electrical switch; do not use

       
     
instructions.
  

       
       

WARNINGS

2 26D4751
CONTENTS
 ................................. 3
Product Features......................................................5
Before You Start.....................................................5
General Installation Information .............................6
Firebox External Dimensions.................................6
Minimum Hearth Dimensions.................................7
 ..................................................7
....................8
 .....................................................10
Gas Line Installation ..............................................12
 ................................................13
 ...............................................14
Illustrated Parts Breakdown..................................14
..............................15
Warranty ..................................................Back Cover

26D4751 3
9. The installation must conform with local codes or, in
the absence of local codes, with the National Fuel Gas
Code, ANSI Z223.l/NFPA54.
10. ThisunitcomplieswithANSI Z21.91ventlessrebox
enclosuresforgas-redunventeddecorativeroomheat-
ers.
11. Do not install heater in a bathroom or bedroom.
12. Correct installation of the logs, proper location of the
heater, and annual cleaning are necessary to avoid
potential problems with sooting. Sooting, resulting from
improper installation or operation, can settle on surfaces
outsidethereplace.Seelogplacementinstructionsfor
proper installation.
13. Avoidanydraftsthatalterburneramepatterns.Donot
allowfanstoblowdirectlyintoreplace.Donotplace
ablowerinsideburnareaofrebox.Ceilingfansmay
createdraftsthatalterburneramepatterns.Sootingand
improper burning will occur.
14. Caution: Candles, incense, oil lamps, etc. produce
combustion byproducts including soot. Vent-free appli-
anceswillnotlterorcleansootproducedbythesetypes
of products. In addition, the smoke and/or aromatics
(scents) may be reburnt in the vent-free appliance which
can produce odors. It is recommended to minimize the
use of candles, incense, etc. while the vent-free appliance
is in operation.
15. Anunventedgas-redheaterusesair(oxygen)fromthe
room in which it is installed. Provisions for adequate
combustion and ventilation air must be provided. See
installation guidelines.
OWNER
Please retain these instructions for future reference .
IMPORTANT
Read these instructions carefully before installing or trying to operate a vent-free gas heater in this rebox.
IMPORTANT SAFETY INFORMATION
1. Due to high temperatures, the appliance should be
locatedoutoftrafcandawayfromfurnitureand
draperies.
2. Children and adults should be alerted to the hazard
of high surface temperature and should stay away
to avoid burns or clothing ignition.
3. Young children should be carefully supervised
when they are in the same room with the appli-
ance.
 4. Donotplaceclothingorotherammablematerial
on or near the appliance.
5. Any safety screen or guard removed for servicing
an appliance, must be replaced prior to operating
the heater.
 6. Installationandrepairshouldbedonebyaqualied
service person.
7. To prevent malfunction and/or sooting, an unvented
gas heater should be cleaned before use at least
annually by a professional service person. More
frequentcleaningmay berequireddue toexces-
sive lint from carpeting, bedding material, etc. It is
imperative that control compartments, burners and
circulating air passageways be kept clean.
8. CARBON MONOXIDE POISONING: Early signs of
carbonmonoxidepoisoningaresimilartotheuwith
headaches, dizziness and/or nausea. If you have these
signs, obtain fresh air immediately. Have the heater
serviced as it may not be operating properly. Continued on page 4







WARNING
INSTALLER
Please leave these instructions with the appliance.

4 26D4751
IMPORTANT SAFETY INFORMATION
Continued from page 3
16. Keep room area clear and free from combustible materi-
als,gasolineandotherammablevaporsandliquids.
17. Unvented gas heaters are a supplemental zone heater.
They are not intended to be a primary heating appli-
ance.
18. Unvented gas heaters emit moisture into the living area.
In most homes of average construction, this does not pose
aproblem.Inhousesofextremelytightconstruction,
additional mechanical ventilation is recommended.
19. During manufacturing, fabricating and shipping, various
components of this appliance are treated with certain
oils,lmsorbondingagents.Thesechemicalsarenot
harmful but may produce annoying smoke and smells
as they are burned off during the initial operation of the
appliance; possibly causing headaches, or eye or lung
irritation. This is a normal and temporary occurrence.
The initial break-in operation should last two to three
hours with the burner at the highest setting. Provide
maximumventilationbyopeningwindowsordoorsto
allow odors to dissipate. Any odors remaining after this
initial break-in period will be slight and will disappear
with continued use.
20. Input ratings are shown in BTU per hour and are for
elevations up to 2,000 feet. For elevations above 2,000
feet, input ratings should be reduced 4 percent for each
1,000 feet above sea level. Refer to the National Fuel
Gas Code.
21. The appliance and its appliance main gas valve must be
disconnected from the gas supply piping system during
any pressure testing of that system at test pressures in
excessof1/2psig(3.5kPa).
22. The appliance must be isolated from the gas supply
piping system by closing its equipment shutoff valve
during any pressure testing of the gas supply piping
system at test pressures equal to or less than 1/2 psig
(3.5 kPa).
23. Do not use this room heater if any part has been under
water. Immediatelycallaqualiedservicetechnician
to inspect the room heater and to replace any part of the
control system and any gas control which has been under
water.
24. Neverburnsolidfuelsinareplacewhereaunvented
room heater is installed.
25. Alwayshaveareplacescreeninplacewhentheappli-
ance is in operation, and unless other provisions for
combustion air are provided, the screen shall have an
opening(s) for induction of combustion air.
26. Donotllspacesaroundthereboxwithinsulationor
other materials. These spaces must be maintained to
preventthereboxfromcomingincontactwithcom-
bustible materials.

26D4751 5
The32LCUFand36LCUFC-Rarevent-freereboxes.Theyfeatureaselfcontainedheat-circulatingsystem.Thisinstallation
manualwillenableyoutoobtainasafe,efcientanddependableinstallationofyourvent-freereboxsystem.
Donotalterormodifythereboxoritscomponentsunderanycircumstances.Anymodicationoralterationoftherebox
system,includingbutnotlimitedtothereboxandaccessories,mayvoidthewarranty,listingsandapprovalsofthissystem
and could result in an unsafe and potentially dangerous installation.
BEFORE YOU START
Carefully inspect the contents for shipping damage. If any parts are missing or damaged, immediately inform the dealer
from whom you purchased the appliance. Do not attempt to install any part of the appliance unless you have all the parts in
good condition.

Check your packing list to verify that all listed parts have been received. You should have the following:
 1. Vent-FreeGasFirebox 3. InstallationandOperatingInstructions
2. Canopy 4. Five (5) sheet metal screws for canopy
WHAT YOU WILL NEED FOR INSTALLATION
TOOLS BUILDING SUPPLIES
• Phillips screwdriver • Square • Framing materials
• Hammer • Piping complying with local codes  •Wallnishingmaterials  
• Saw and / or sabersaw • Tee joint • Caulking material (noncombustible)
• Level • Pipe wrench • Fireplace surround materials (noncombustible)
• Measuring tape • Pliers
• Electric drill and bits • Pipe sealant approved for use with propane/L.P.G. (resistant to sulfur compounds)
Refer to the installation instructions provided with the log sets for items required for log set installation.
PRODUCT FEATURES


 

WARNING

and are for design and framing reference only. Actual installations may vary due to
         

NOTICE

6 26D4751
In planning the installation for the appliance it is necessary to determine where the unit is to be installed and whether optional
accessories are desired. Gas supply piping should also be planned. The following steps represent the normal sequence of
installation. Each installation is unique, however, and might require a different sequence.
1. Positionreboxpriortoframingorintopreparedframing.
2. Plumbgasline.(Gasconnectionsshouldonlybeperformedbyanexperienced,licensed/certiedtradesman).
3. Install vent-free gas log heater per the instructions provided with the vent-free gas log heater.
4. Completenishwallmaterial,surroundandoptionalhearthextensiontoyourindividualtaste.
GENERAL INSTALLATION INFORMATION
Figure 1 - Firebox Dimensions
32LCUFF 36LCUFC-R
A 37" 41"
B 32" 36"
C 16" 18"
D 28⅞" 32"
E 18⅝" 20½"
F 23¼" 27¼"
G28½" 30¼"
H 29⅞" 33⅞"
I 5⅜" 5⅜"
J 28⅜" 31¼"
1" 1"
L 34⅜" 37⅜"
M73/16" 9¾"
FIREBOX EXTERNAL DIMENSIONS
2.75"
M
G
C
H
E
F
D
I
JB
K
2.50"2.50"
L
A

26D4751 7
MINIMUM HEARTH DIMENSIONS
GENERAL INSTALLATION INFORMATION and LOCATION OF FIREBOX
Figure 2 - Minimum Hearth Dimensions
LOCATION OF FIREBOX
Carefully select the best location for installation of your
vent-freerebox.Thefollowingfactorsshouldbetaken
into consideration:
• Clearance to side wall, ceiling, woodwork and
windows. See “Clearances/Height Requirements on
page 8. Minimum clearances to combustibles must
be maintained.
• Location must not be affected by drafts caused by
kitchenexhaustfans,ceilingfans,returnairregisters
for forced air furnaces / air conditioners, windows or
doors.
• Installation must provide adequate ventilation and
combustion air.
• DO NOT INSTALL THIS FIREBOX IN A BED-
ROOM OR BATHROOM.
 • Locationshouldbeoutofhightrafcorwindyor
drafty areas.
• DO NOT INSTALL WHERE CURTAINS, FURNITURE, CLOTHING OR OTHER FLAMMABLE OBJECTS
ARE LESS THAN 42" FROM FRONT OF HEATER.
 • Neverobstructthefrontopeningofthevent-freereboxorrestricttheowofcombustionandventilationair.
 • Minimizemodicationstoexistingconstruction.RefertoFigure3belowforlocationsuggestions.
 • Donotinstallinthevicinitywheregasolineorotherammableliquidsmaybestored.Thevent-freereboxmustbe
kept clear and free from these combustible materials.
Figure 3 - Location of Firebox
32LCUFF 36LCUFC-R
A 22⅜" 25⅞"
B 12¾" 15"
C 28⅝" 32½"
D 28" 30¼"
E 23¼" 25⅝"

8 26D4751
6"
Minimum
42"
Minimum
6"
Minimum
Ensure that minimum clearances shown in Figures 4 through 7 are main-
tained. Left and right clearances are determined when facing the front of
therebox.
Follow these instructions carefully to ensure safe installation. Failure to
followtheserequirementsmaycreatearehazard.
1. Sidewall clearances: The clearance from the inside of the appliance
to any combustible wall should not be less than 6". See Figure 4.
2. Ceiling clearance: The ceiling must be at least 42” from the top of
thereboxopening.See Figure 4.
3. Back wall clearance: The appliance may be placed against a com-
bustible back wall.
Figure 4 - Clearance and Height
Requirements
4. Floor clearance: Thisinnerchamberreboxoormustbeinstalledatleast1"aboveanycombustibleooringmate-
rial,suchascarpetingorasphalttile,whichiscloserthan14"tothebaseoftherebox.See Figure 5.
Or
  Theinnerchamberreboxoormaybeinstallednearertotheoorifaminimumof14"ofnoncombustiblematerial
suchasslateormarbleisinstalledbetweenthebaseofthereboxandthecombustibleooring. See Figure 6.
Figure 5 - Minimum Clearance above
Combustible Flooring
Figure 6 - Minimum Clearance above Combustible
Flooring with Non-Combustible Material Installed at
Base of Fireplace
14" Minimum
Combustible
Material 1" minimum for
LCUF32 and 36
Can be less than 1"
for LCUF32 and 36 Non-Combustible
Material
CLEARANCES and HEIGHT REqUIREMENTS

26D4751 9
12"
10"
8"
6"
21/2"
12"
16"
19"
21"
23"
Combustible material
can contact top of
replace.
Non-combustible
material only if
needed to cover
radiant top face above
5. Mantel clearances: The canopy supplied with the unit must be installed. If a combustible mantel is installed, it must
meet the clearance requirements as shown in Figure 7A. However, if lower mantel height is desired, see page 14 and
Figure 7B for canopy options.
Figure 7A - Mantel Clearances Figure 7B - Mantel Clearances for Wide Prole
Canopy Only
FIREPLACE
WALL
COMBUSTIBLE
MATERIAL AREA
HOOD
TOP VIEW
Figure 8- Mantel Clearances
CLEARANCES and HEIGHT REqUIREMENTS

10 26D4751
H
G
D
F
E
A
C
B
A
1/2" or 5/8"
C
A
G
C
G
A
FIREBOX FRAMING
Fireboxframingcanbebuiltbeforeoraftertheapplianceissetinplace.ConstructreboxframingfollowingFigures 9
through 12 andthechartbelowforyourspecicinstallationrequirements.See Figure 1 on Page 6 forreboxdimensions.
Theframingheadersmayrestonthetopofthereboxstandoffs.
Thereboxmaybeinstalleddirectlyonacombustibleoororraisedonaplatformofanappropriateheight.Whenthe
reboxisinstalleddirectlyoncarpeting,tile,orothercombustiblematerial,otherthanwoodooring,thereboxshallbe
installedonametalorwoodpanelextendingthefullwidthanddepthoftheenclosure.
Theclassication"noncombustiblematerial"includes,butisnotlimitedto:stone,brick,andmortar.Noncombustiblesare
safetooverlaytheblack-paintedmetalface,includingradiantplates,anddonotposearehazard.Anynoncombustible
nishmaterialmustnotextendpastorinterferewiththereplaceopening.
Theclassication"combustiblematerial"incudes,butisnotlimitedto:plywood,drywall,andparticleboard.Combustible
materialsmaycontactthesides,bottom,orbackoftherebox.Donotoverlaytheblackpaintedfacewithcombustible
matierals.
Figure 9 - Corner Installation
Figure 11 - Stud Location
Figure 10 - Inside Chase Installation
Figure 12 - Recessed Installation


WARNING
32LCUFF 36LCUFC-R
A 37" 41¼"
B 34½" 37¾"
C 29" 32"
D 14⅞" 16⅜"
E 61¾" 68⅞"
F 30⅞"34½"
G 16"18"
H 43¾" 48¾"
½" or ⅝"

26D4751 11
K
J
FIREBOX FRAMING
1. Bendoutthenailingangeslocatedoneachsideoftherebox.
 2. Slidethereboxintopreparedframingorpositionreboxinitsnalpositionandframelater.
 3. Levelthereboxbycheckingthetopedgeoftherebox.Shimifnecessary.
 4. Anchorreboxtothesideframingmembersusing8dnailsorothersuitablefasteners.See Figure 14.
5. The canopy must be installed for safe operation of the heater. See page 13 for canopy installation details.
Whennishingacustomcabinet,mantel,orotherbuilt-inenclosure,theopen-
ingsizetoaccommodatethereplacewithtriminstalledisasfollows:
Figure 13 - Custom Cabinet
Figure 14 - Location of Nailing Flanges

full consideration to the clearance and

manual.
WARNING
This appliance is approved for the installation of drywall or other combustible
materialsagainstthesidesortopoftheblack-paintedreboxface.
Noncombustiblefacingswillnotburnwhenexposedtoheatcomingoffthis
replace.Theclassication,“Noncombustiblematerial”includesbrickand
mortar, stone or marble. These are safe to overlay the black-painted metal face
anddonotposearehazard.Neveroverlaptherelaceopening.
32LCUFF with trim 36LCUFC-R with trim
37¾" 41¾"
J 35⅜" 38⅞"
Nail Sides
Through Nailing
Flanges

12 26D4751
GAS LINE INSTALLATION
Consult all local codes. All gas piping must be installed to comply with local codes, or in the absence of local codes, with
the latest edition of the National Fuel Gas Code ANSI Z223.1/NFPA54.
The 1/2"gaslinemayentereitherfromtheleftsideorrightsideoftherebox.Gasaccessholesareprovidedonbothsides
oftherebox.
A listed manual shutoff valve must be installed upstream of the appliance. A union tee and plugged 1/8" NPT pressure tapping
point should be installed upstream of hte appliance.
IMPORTANT: Install main gas valve (equipment shutoff valve) in an accessible location. The main gas valve is for turning
on or shutting off the gas to the replace.
A sediment trap may be upstream of the heater to prevent moisture and contaminants from passing through trap to the heater
controls and burners. Failure to do so could prevent the heater from operating reliably. Consult applicable codes.
Anexternalregulatormustbeusedonallpropane/L.P.G.heaters,inadditiontotheregulatorttedtotheheater,toreduce
thesupplytankpressureto13"w.c.(maximum).Anycoppertubingusedtosupplypropane/L.P.G.fromthetankmustbe
internally tinned.
Note: When connecting propane / L.P.G. vent-free room heaters, you must use pipe sealant resistant to
propane / L.P.G.
Important: Hold heater regulator with a wrench to prevent movement when connecting to inlet piping.

is different, DO NOT INSTALL THE HEATER. Contact your dealer for the correct model.
After completing connection, test all gas joints from the gas meter to the gas heater regulator for leaks. Using soap and water
solutionoragassniffer.DONOTUSEANOPENFLAME.


WARNING
Connecting directly to an unregulated
      

WARNING
Do not connect directly to natural gas 1/2 PSI or 2 PSI systems. Always make sure

WARNING

26D4751 13
CANOPY INSTALLATION
INSTALLING CANOPY
AcanopyisfurnishedwitheachreboxandMUST be installed for safe operation. See Figure 15.
1. Remove the three (3) screws from the top front frame assembly. Also remove the two (2) screws on the side frames.
See Figure 15.
2. Align the canopy with the holes in the top frame.
3. Replace the screws previously removed.
4. Tighten side screws. Make sure the canopy is level and
secure.
     
     

decorative room heater.
WARNING
    

room heater.
WARNING
Figure 15 - Installing Canopy

14 26D4751
4
2
1
3
*Not illustrated, see following page.
OPTIONAL EqUIPMENT and ILLUSTRATED PARTS LIST
OPTIONAL WIDE CANOPY
The optional wide canopy can be installed. See installation instructions provided with kit.
ITEM DESCRIPTION qTY 32LCUF-F 32LCUF-R 36LCUFC-R
1 Canopy 1 71D0023 71D0023 71D0500
Screen Panel 2 070942 070942 26D4563
3 Screen Rod 2 26D0138 26D0138 26D0132K

1 Standard Brass Canopy 1 BRCU32 BRCU32 BRCU36
1 Wide Brass Canopy 1 BRC32 BRC32 BRC36
4 Brass Trim Curved Design 1 BRTK32C BRTK32C BRTKM36C
4 Pewter Trim Curved Design 1 PWTK32C PWTK32C PWTKM36C
4 Black Trim Curved Design 1 BLTK32C BLTK32C BLTM36C
5 Outside Air Kit* 1 AK-4 AK-4 AK-4

26D4751 15

8'max.
COMBUSTION AIR
1. Locatecombustionairassemblyatanexteriorlocationwhichisnotlikelytobeaccidentallyblockedinanymanner.
Locate assembly a min. of 12" above the snow line to prevent blockage by snow accumulation.
2. Never mount the combustion air inlet assemblyin a garage or storage area where combustible fumes such as gasoline
mightbedrawnintothereplace.
3. Combustion air can be drawn from the crawl space under a house when an adequate supply of air is provided by open
ventilation.
4. CAUTION: Do not take combustion air from attic space or garage space.
5. Locate air supply inlet at least 3' away from any applaince vent terminal.
6. Avoidextremelylongrunsandnumerousturnsintheductleadingfromthereplacetothecombustionairassembly.
Theseconditionsincreasetheresistancetothefreeowofairthroughtheduct.See Figures 16 through 19 for methods
of installing the outside air for combustion assemblies.
Figure 16 - Basement Installation
Figure 17 - Concrete Slab Installation
(Optional Outside Air Runs)
Above
Snow
Level
Ground
Level
Basement
Wall
Inlet Grill in
Soft
(Overhang)
Figure 19 - 45° Corner Installation on
Slab Floor
Figure 18 - Installation Above Basement or
Crawl Space
Inside Wall
Outside
Wall
Duct Extended
to Miss Joist
To Outside Wall
Note: Fireplace model in illustrations may not be representative of your appliance.

16 26D4751

The use of outside air for combustion is optional unless required by building codes. It is only necessary to supply outside
combustionairtoonesideofthereplace.UsethemodelAK4combustionairkit.

1. Remove the cover plate from the 4" outlet opening location on the left or
rightoutsideofthereplace.
2. Place the insulation ring between the AK-4 starting collar and fire-
place wall.
3. Placethestartingcollar(4")intotheholeonthesideofreplace.Fastenitinplacewiththefoursheetmetalscrews
provided. See Figures 20 and 21.
Note: The air starting collar extends through the replace outer wrap. When the air starting collar is
securely attached, it will form a seal against the replace wall.
4. Attach outside duct to starting collar with duct clamp or screws. See Figure 21.
DO NOT remove the
cover if the outside air

WARNING
Figure 20 - Attaching Outside Air Starting Collar
and Insulation Ring to Left Side of Fireplace
Figure 21 - Attaching Outside Duct
to Starting Collar
Insulation Ring
AK-4 Starting
Collar
Sheet
Meal
Screws
Left Side of
Fireplace
Shorter End
of Air Starting
Collar
Air Starting
Collar
Duct
Screws
Left Side of
Fireplace
5. Cut a 6-inch diameter opening for modelAK-4 in the outside
wall covering where the outside vent is to be located. See
Figure 22.
6. Select and cut a piece of duct long enough to attach to the
replaceandstickoutatleast3"beyondthefaceofthewall
to which the AK-4 inlet air vent will be attached. Cut duct
with a standard pocket knife. See Figure 21.
Figure 22 - Combustion Air Assembly for
Model No. AK-4
Nail
Holes


duct. Always use UL Listed Class 0 or
1 duct material.
WARNING
6" Diameter
Hole
Duct
Extending
3"min.
AK-4 Inlet
Air Vent
Screw
Screws
Continued

26D4751 17
(CONTINUED)
7. If the duct is the insulated type, push the insulation back from one end of
theductapproximately2".See Figure 23.
8. Sliptheexposedendoftheductoverthestartingcollaronthereplace.
9. Using the sheet metal screws provided, secure the duct end to the collar
attachedtothereplace.
10. Nail or screw the combustion air assembly to the surface of the wall.
Note: If the wall covering is brick or stone, use appropriate
masonry fasteners. If necessary, splice the duct. Use a model
403-duct connector to splice duct sections.
INSTALLING MODEL 403 DUCT CONNECTOR
1. Pushinsulationbackapproximately2"fromtheendofeachduct.
2. Slipeachductoverductconnectoruntilanequallengthofconnectorextendsintoeachduct.
3. Place duct clamp over the end of each duct. Tighten duct clamp down snuggly.
4. Push insulation back into place and over duct clamp.
Figure 23 - Installing Duct
Connector 403
Approximately
2"
Insulation
Duct
Connector
Duct Clamp


18 26D4751
NOTES

26D4751 19
LIMITED LIFETIME WARRANTY POLICY
Thefollowingcomponentsarewarrantedforlifetotheoriginalowner,subjectofproofofpurchase:Firebox,
CombustionChamber,HeatExchanger,Grate,andStainlessSteelBurners.
FIVE YEAR WARRANTY
The following components are warranted for 5 years to the original owner, subject of proof of purchase: Vent Free
Ceramic Fiber Logs, Catalytic Filter and Aluminized Burners.
BASIC WARRANTY
MHSC warrants the components and materials in your gas appliance to be free from manufacturing and material
defects for a period of two years from date of installation. After installation, if any of the components manufactured
by MHSC in the appliance are found to be defective in materials or workmanship, MHSC will, at its option, replace
or repair the defective components at no charge to the original owner. MHSC will also pay for reasonable labor
costs incurred in replacing or repairing such components for a period of two years from the date of installation.
Any products presented for warranty repair must be accompanied by a dated proof of purchase.
ThisLimitedLifetimeWarrantywillbevoidiftheapplianceisnotinstalledbyaqualiedinstallerinaccordance
with the installation instructions. The Limited Lifetime Warranty will also be void if the appliance is not operated
andmaintainedaccordingtotheoperatinginstructionssuppliedwiththeappliance,anddoesnotextendto(1)
rebox/burnerassemblydamagebyaccident,neglect,misuse,abuse,alteration,negligenceofothers,including
theinstallationthereofbyunqualiedinstallers,(2)thecostsofremoval,reinstallationortransportationofdefec-
tive parts on the appliance, or (3) incidental or consequential damage. All service work must be performed by an
authorized service representative.
Thiswarrantyisexpresslyinlieuofotherwarranties,expressorimplied,includingthewarrantyofmerchantability
oftnessforpurposeandofallotherobligationsorliabilities.MHSCdoesnotassumeforitanyotherobligations
or liability in connection with the sale or use of the appliance. In states that do not allow limitations on how long
animpliedwarrantylasts,ordonotallowexclusionofindirectdamage,thoselimitationsofexclusionsmaynot
apply to you. You may also have additional rights not covered in this Limited Lifetime Warranty.
MHSC reserves the right to investigate any and all claims against the Limited Lifetime Warranty and decide upon
method of settlement.
IF WARRANTY SERVICE IS NEEDED...
1. Contact your supplier. Make sure you have your warranty, your sales receipt and the model/serial number of
your MHSC product.
2. DONOTATTEMPTTODOANYSERVICEWORKYOURSELF.

AUGUST 2008
26D4751 • Rev. 10
MHSC
149 Cleveland Drive • Paris, Kentucky 40361
www.mhsc.com