MAKINEX Hose2Go User manual

Hose2Go
Pressurised Water Supply Unit
OPERATOR’S MANUAL
Rev 0919

TABLE OF CONTENTS
TABLE OF CONTENTS .......................................................................................................1
INTRODUCTION ..................................................................................................................1
DISCLAIMER........................................................................................................................1
ABOUT THIS MANUAL........................................................................................................2
KEY TERMS......................................................................................................................2
PRODUCT INFORMATION..................................................................................................3
SAFETY INFORMATION...................................................................................................3
SAFETY DECALS .............................................................................................................4
PRODUCT DESCRIPTION AND SPECIFICATIONS.........................................................4
OPERATION ........................................................................................................................6
BEFORE USE....................................................................................................................6
MAINTENANCE ...................................................................................................................8
GENERAL RECOMMENDATIONS....................................................................................8
HOSE2GO SPECIFIC MAINTENANCE.............................................................................8
STORAGE............................................................................................................................9
TROUBLESHOOTING........................................................................................................10
LIMITED WARRANTY........................................................................................................11
WARRANTY: (Ex-factory/ Reseller premise) ...................................................................11
WARRANTY EXCLUSIONS ............................................................................................11
RESPONSIBILITY OF THE CONSUMER UNDER THIS LIMITED WARRANTY: ............12
CLAIM PROCEDURE......................................................................................................12
CONTACT INFORMATION ................................................................................................13

HOSE2GO –USER MANUAL REV0919 Page 1 of 15
INTRODUCTION
Thank you for purchasing a MAKINEX product.
This manual provides information and procedures to safely operate and maintain the
HOSE2GO. For yours and/or other’s safety and protection from injury, carefully read,
understand and observe the safety instructions described in this manual.
Keep this manual or a copy of it with the machine. If you lose this manual or need an
additional copy, please contact MAKINEX. This machine is designed and built with user
safety in mind; however, it can present hazards if improperly operated and/or serviced.
Please follow the operating instructions carefully. If there are any questions regarding
operating or servicing of this product, please contact MAKINEX.
The information contained in this manual was based on devices in production at the time of
publication. MAKINEX reserves the right to change any portion of this information without
notice.
All rights, especially copying and distribution rights are reserved.
Copyright 2019 by MAKINEX.
No part of this publication may be reproduced in any form or by any means, electronic or
mechanical, including photocopying, without express written permission from MAKINEX.
Any type of reproduction or distribution not authorised by MAKINEX represents an
infringement of valid copyrights and will be prosecuted. We expressly reserve the right to
make technical modifications, without due notice, which aim at improving our machines or
their safety standards.
DISCLAIMER
MAKINEX and its affiliates take no responsibility for any damage, injury or death resulting
from the incorrect or unsafe use of this product. Use of this product should be undertaken by
competent persons only. It is the operator’s responsibility to ensure that the following safety
procedures are followed. If you are unsure, do not operate this product.
Record the model and serial numbers as well as date and place of purchase for future
reference. Have this information available when ordering parts and when making technical or
warranty inquiries
MAKINEX SUPPORT
Refer to contact details on pg. 13
MODEL NO.
H2G
SERIAL NO.
DATE OF PURCHASE
PURCHASE LOCATION

HOSE2GO –USER MANUAL Page 2 of 14
ABOUT THIS MANUAL
This manual uses the following symbols to help differentiate between different kinds of
information. The safety symbol is used with a key word to alert you to potential hazards in
operating and owning Hose2Go. Follow all safety messages to avoid or reduce the risk of
serious injury or death.
KEY TERMS
READ
CAREFULLY
READ CAREFULLY –refers to important information that should be
paid careful attention.
CAUTION
CAUTION - indicates a potential hazardous situation which, if not avoided,
may result in minor or moderate injury
WARNING
WARNING –indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury
DANGER
DANGER –indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury
PROHIBITED
PROHIBITED –identifies actions that should never be carried out by any
one interacting with the machine.
These safety warnings do not eliminate all possible hazards that could occur therefore it is
essential to use common sense and to strictly follow any instructions to prevent accidents.

HOSE2GO –USER MANUAL Page 3 of 14
PRODUCT INFORMATION
SAFETY INFORMATION
WARNING
Read this manual thoroughly before operating your Hose2Go.
Failure to follow instructions could result in serious injury or death.
WARNING
MAKINEX Hose2Go is designed for ease of use and safety.
However, damage to the device and personal injury is possible if
used incorrectly. Instruct all operators in care and use of the
machine before use.
WARNING
RISK OF EXPLOSION
Contents of device are under pressure (even when empty). Do not
attempt to disassemble device as serious injury may occur.
Warranty is voided if disassembled (other than by registered
service agent).
•ALWAYS wear PPE appropriate to task; such as goggles, ear muffs, gloves, and
closed foot wear.
•ALWAYS use Makinex branded hose fittings as they are tested at rated pressure. Use
of non-genuine accessories may reduce performance and/or working life of device.
•ALWAYS use care in filling tanks and ensure that a firm connection is made between
connectors.
•ALWAYS Make sure connectors/hose are free of debris that could obstruct/damage
device.
•NEVER introduce foreign agents (i.e. soaps, solvents, colours, etc.) to device. Doing
so will void warranty.
•ALWAYS follow manufacturer’s recommendations, including those of equipment used
in conjunction with Hose2Go (for example; Concrete saw user’s manual)
WARNING
RISK OF FALL HAZARD
Use of Hose2Go can create puddles and slippery surfaces.
WARNING
RISK OF EXPLOSION OR DAMAGE TO DEVICE
Device is designed for use on water main’s pressure and has been
tested to 70 Psi. Do not connect to sources which you feel may
exceed this pressure. i.e. stand pipe into water main, hydrant
without pressure reducer, irrigation pump, etc. Doing so will void
warranty.

HOSE2GO –USER MANUAL Page 4 of 14
•Keep operating area clear of obstacles.
•DO NOT operate the machine with missing, broken, or non-genuine parts.
•DO NOT drag the device using only the hose as this may cause damage to the
device and/or fittings.
•NEVER spray near power source.
WARNING
RISK OF ELECTRICAL SHOCK
•Risk of electrocution.
•Be aware of electrical hazards whilst performing task as contact
with power source may cause electric shock.
SAFETY DECALS
(On side)
(At rear also)
(Concealed in
base) Do not
attempt to
disassemble
Serial # Decal

HOSE2GO –USER MANUAL Page 5 of 14
PRODUCT DESCRIPTION AND SPECIFICATIONS
The MAKINEX Hose2Go is a pressurised water supply device. It is designed and engineered
to simplify the process of supplying water in situations where regular hosing is difficult. The
Hose2Go includes a multi-function nozzle, an on/off valve, 3 metres of reinforced hose, all
mounted on a compact two chamber frame design.
MAKINEX Hose2Go
OVERALL WEIGHT - Empty
6kg/13.2lb
OVERALL WEIGHT –Full
20kg/44lb
OVERALL WIDTH
325mm/12.8inch
OVERALL HEIGHT
800mm/31.5inch
OVERALL DEPTH
144mm/5.7inch
HOSE LENGTH
3m/18ft
PRESSURE OUTPUT
7-10psi
FLOW RATE
Approx. 0.5 –7.0 L/min (0.13 - 1.85 gal/min)

HOSE2GO –USER MANUAL Page 6 of 14
OPERATION
BEFORE USE
Inspect Device
1. Check for any damage. Check for loose or missing fasteners (2x nut/bolt in base & 2x
screws in handle).
2. Ensure all fittings are tight (do not over tighten using tools as damage may occur to
fittings).
Filling Device
WARNING
Using high-pressure pumps, direct connection to water mains or
other high-pressure sources to fill Hose2Go that exceed rated
pressure (70 psi) will void warranty.
•ONLY use water.
•DO NOT mix with oil, detergents, etc.
•DO NOT modify device in any way.
NOTE: IMPROPER treatment of Hose2Go can damage it and shorten its working life.
DO NOT attempt to open device to alter or to repair it. This must ONLY be done by
Makinex approved service technician.

HOSE2GO –USER MANUAL Page 7 of 14

HOSE2GO –USER MANUAL Page 8 of 14
MAINTENANCE
GENERAL RECOMMENDATIONS
Regular maintenance will improve the performance and extend the life of your MAKINEX
product.
The Hose2Go warranty does not cover items that have been subjected to operator abuse or
negligence or disassembly.
Should you have questions about replacing components on your Hose2Go, please contact
dealer for assistance.
HOSE2GO SPECIFIC MAINTENANCE
This device is designed for the rigours of the construction industry. However, care is still
required to maximise its working life. If the instructions in this manual are heeded, you can
expect a long and rewarding service from your MAKINEX Hose2Go.
Cleaning
Hose and wipe down Hose2Go using soapy water be cautious not to introduce debris into
inner workings.
Using a high-pressure washer is NOT recommended as this could strip the decals on the
device. Decals include important information such as serial number and instructions.
DO NOT clean internally with soaps or other cleaning agents, rinse with fresh water and
empty to store.
Clear Debris
Before use, clear debris from hose line. If debris has entered the hose line disconnect from
Hose2Go base (be aware that if the device is full water will spray out) and connect the free
hose to a tap, flush out any debris before reconnecting and refilling Hose2Go.
Check multi spray nozzle
Ensure nozzle is connected securely and functioning correctly. Selector should rotate
between options smoothly with a slight click at each function.
Check one-way valve
Inspect one-way valve on hose fitting and ensure it is working correctly. Ensure no debris is
in mechanism.
NOTE: IMPROPER treatment of Hose2Go can damage it and shorten its life.

HOSE2GO –USER MANUAL Page 9 of 14
Threaded fittings
Check threaded fittings are tight to ensure a good seal. Do not use hand tools to over tighten
threaded fittings as damage may occur.
Tools can be used to gently loosen fittings on hose if required.
The barb fitting on the top lid of the device can be tightened/loosened by hand. Use cloth to
improve grip if tight. Use of multi grip plyers may be required if too tight. Use gently avoiding
damage to barb and Hose2Go top lid frame.
STORAGE
Long term storage instructions
It is not advised to store a full Hose2Go for long periods (weeks/months) as this may reduce
performance of your product. Empty your Hose2Go before long-term storage.
DO NOT clean inside tanks with soaps or other cleaning agents/products, rinse with fresh
water and empty.

HOSE2GO –USER MANUAL Page 10 of 14
TROUBLESHOOTING
TROUBLE SHOOTING GUIDE
PROBLEM
CAUSE
REMEDY
Pump does not fill
Valve faulty
Inspect valve on hose
Blockage in hose
Remove hose from Hose2Go and
flush with tap water from either end
Check for blockages at barbed
fittings
Blockage in top cap
Inspect inlet for debris
Irregular variations in
pressure
Machine being used has
blockage
Refer to applicable machine’s
operator manual
Valves blocked by debris
Clean the valves
Air in system
Follow instructions on device to fill
from empty
Hose blocked by debris
Remove hose from Hose2Go and
flush with tap water from either end
Pressure drop
Tank empty
Fill following procedure in manual/
and on Hose2Go
Blockage in hose
Remove hose from Hose2Go and
flush with tap water from either end
Faulty valve
Inspect valves for blockages/damage
Water leaking from main
housing
Ruptured bladder
Return to MAKINEX service
department
Cracked housing
Return to MAKINEX service
department
Water accumulated whilst
stowed on side
When stowed on side or upside-
down water can accumulate in upper
housing. This is normal do not
confuse with leaking.

HOSE2GO –USER MANUAL Page 11 of 14
LIMITED WARRANTY
In order to take advantage of the MAKINEX limited warranty, you must have maintenance
performed according to the schedule (contained in relevant owner’s manual supplied with
this product), by an authorised MAKINEX dealer or MAKINEX service technician.
In order to ensure your safety, we strongly recommend that you only use an authorised
MAKINEX dealer for servicing. Only authorised MAKINEX dealers have access to all the
special tools, technical information, parts and training required to maintain your MAKINEX
product in peak operating condition.
MAKINEX warrants each new Hose2Go to be free from defects in material and workmanship
under normal domestic and industrial use and service for the period specified below,
conditional to the limitations and exclusions printed on this page. This warranty applies only
to new MAKINEX Hose2Go’s distributed by us and by our authorised MAKINEX dealers.
Our goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and compensation for
any other reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure does not
amount to a major failure.
WARRANTY: (Ex-factory/ Reseller premise)
MAKINEX warrants to the original purchaser:
•External housing, internal workings, and fittings will be free of defects in material and
workmanship for a period of (6) months from the original date of purchase.
WARRANTY EXCLUSIONS
This warranty does not cover the following repairs and equipment:
Normal Wear
The Hose2Go is designed for use in harsh environments, therefore, cosmetic damage
including; scratches, minor dents/damage caused throughout use is considered “normal
wear”.
Installation, Use and Maintenance
This warranty will not apply to parts and/or labour if this Hose2Go is deemed to have been
misused, neglected, involved in an accident, abused, loaded beyond the Hose2Go’s limits,
modified, installed improperly or connected incorrectly to any water supply. Normal
maintenance such as cleaning, adjustments to fittings, obstruction due to build-up is not
covered by this warranty.

HOSE2GO –USER MANUAL Page 12 of 14
Other Exclusions
This warranty excludes:
•Cosmetic defects such as, decals, etc.
•Failures due to acts of God and other force majeure events beyond the
manufacturer’s control.
•Problems cause by parts that are not original MAKINEX parts.
RESPONSIBILITY OF THE CONSUMER UNDER THIS LIMITED WARRANTY:
•Only clean, potable water should be used through our Hose2Go with pressure not
exceeding 70psi.
•Maintenance services are not covered under warranty.
•It is the consumer’s responsibility to deliver the device in question to our service
premises or to the premises of our appointed agent at the consumer’s expense for
replacement or repair as applicable.
CLAIM PROCEDURE
•Contact MAKINEX by phone or email informing us of your machines problem or
defect.
•Once the extent of the claim has been assessed, we retain the right to compensate
the consumer for such defect, or repair (parts & labour), or replace the machine
under warranty.
•All warranties will be carried out by MAKINEX authorised staff or appointed agents at
a premise to be determined by the Manufacturer.
•Transportation charges on product submitted for repair or replacement under this
warranty are the sole responsibility of the purchaser. This warranty only applies to
the original purchaser and is not transferable.
•It is the responsibility (and cost) of MAKINEX or our appointed agent to return the
device to be repaired or replaced under warranty to the consumer- this is valid for
domestic territories only (e.g. Australian units will be delivered within Australian
territory, USA units will be delivered within USA territory and European units will be
delivered within its designated country’s territories).
•Warranty calls will only be carried out by our representatives and not via client’s
choice of repairer. We will not accept back charges for any work not carried out by
our representatives or accept any charges due to equipment being un-operational for
any reason even during its warranty period.

HOSE2GO –USER MANUAL Page 13 of 14
CONTACT INFORMATION
For sales, service, warranty and parts for all MAKINEX products; please refer below.
SALES, SERVICE, SPARE PARTS & WARRANTY
AUSTRALIA
SALES
TEL [phone] or
[phone]
WEB www.makinex.com.au
SERVICE, SPARE PARTS & WARRANTY
EMAIL servi[email protected]
USA
SALES
TEL [phone]
WEB www.makinex.com
SERVICE, SPARE PARTS & WARRANTY
EMAIL [e-mail]
UK
WEB www.makinex.co.uk
EUROPE
TEL [phone] or
[phone]
EMAIL [email protected]
CHINA
TEL [phone]
EMAIL [email protected]
Or your nearest MAKINEX distributor
We have very knowledgeable, experienced staff to assist you with help and advice.

HOSE2GO –USER MANUAL Page 14 of 14