Renishaw Kiosk workstation User manual

Kiosk workstation user's guide
Documentation part number: H-1000-5422-02-A
Kiosk workstation user's guide
www.renishaw.com
Issued 10 2022
1

Kiosk workstation general information
© 2020 ‐ 2022 Renishaw plc. All rights reserved.
This document may not be copied or reproduced in whole or in part, or transferred to any other media or language by any means, without the
prior written permission of Renishaw.
Disclaimer
WHILE CONSIDERABLE EFFORT WAS MADE TO VERIFY THE ACCURACY OF THIS DOCUMENT AT PUBLICATION, ALL WARRANTIES,
CONDITIONS, REPRESENTATIONS AND LIABILITY, HOWSOEVER ARISING, ARE EXCLUDED TO THE EXTENT PERMITTED BY LAW.
RENISHAW RESERVES THE RIGHT TO MAKE CHANGES TO THIS DOCUMENT AND TO THE EQUIPMENT, AND/OR SOFTWARE AND THE
SPECIFICATION DESCRIBED HEREIN WITHOUT OBLIGATION TO PROVIDE NOTICE OF SUCH CHANGES.
Trade marks
RENISHAW®, the probe symbol and REVO®are registered trade marks of Renishaw plc.
Renishaw product names, designations and the mark ‘apply innovation' are trade marks of Renishaw plc or its subsidiaries.
Other brand, product or company names are trade marks of their respective owners.
WEEE
The use of this symbol on Renishaw products and / or accompanying documentation indicates that the product should not be mixed with
general household waste upon disposal. It is the responsibility of the end user to dispose of this product at a designated collection point for
waste electrical and electronic equipment (WEEE) to enable reuse or recycling. Correct disposal of this product will help to save valuable
resources and prevent potential negative effects on the environment. For more information, please contact your local waste disposal service
or Renishaw distributor.
Warranty
Unless you and Renishaw have agreed and signed a separate written agreement, the equipment and/or software are sold subject to the
Renishaw Standard Terms and Conditions supplied with such equipment and/or software, or available on request from your local Renishaw
office.
Renishaw warrants its equipment and software for a limited period (as set out in the Standard Terms and Conditions), provided that they are
installed and used exactly as defined in associated Renishaw documentation. You should consult these Standard Terms and Conditions to find
out the full details of your warranty.
Equipment and/or software purchased by you from a third-party supplier is subject to separate terms and conditions supplied with such
equipment and/or software. You should contact your third-party supplier for details.
Kiosk workstation user's guide
www.renishaw.com
Issued 10 2022
2

Care of equipment
Renishaw probes and associated systems are precision tools used for obtaining precise measurements and must therefore be treated with
care.
Changes to Renishaw products
Renishaw reserves the right to improve, change or modify its hardware or software without incurring any obligations to make changes to
Renishaw equipment previously sold.
Company registration details
Renishaw plc. Registered in England and Wales. Company no: 1106260. Registered office: New Mills, Wotton-under-Edge, Gloucestershire,
GL12 8JR, UK.
Packaging
To aid end user recycling and disposal the materials used in the different components of the packaging are stated here:
Packaging component Material 94/62/EC code 94/62/EC number
Crate Plywood FOR 50
Packing foam Low density polyethylene LDPE 4
Bag Plastic / aluminium C/LDPE 90
Kiosk workstation user's guide
www.renishaw.com
Issued 10 2022
3

Kiosk workstation product compliance
EU declaration of conformity
Contact Renishaw plc or visit www.renishaw.com/EUCMM for the full EU declaration.
UK declaration of conformity
Contact Renishaw plc or visit www.renishaw.com/UKCMM for the full UK declaration.
REACH regulation
Information required by Article 33﴾1﴿ of Regulation ﴾EC﴿ No. 1907/2006 ﴾“REACH”﴿ relating to products containing substances of very high
concern (SVHCs) is available at:
www.renishaw.com/REACH
China RoHS
Contact Renishaw plc or visit www.renishaw.com/ChinaRoHSCMM for the full China RoHS tabulation.
Kiosk workstation user's guide
www.renishaw.com
Issued 10 2022
4

Kiosk workstation safety
Where this symbol is displayed on the product the user must refer to the installation and user guide for information and safety
advice.
If the equipment is used in a manner not specified by the manufacturer then the safety of the equipment may be impaired.
WARNING: To prevent unexpected machine movement, the user is advised to isolate the machine from the electricity supply,
compressed air or other energy sources in accordance with the machine manufacturer's instructions before entering the danger
zone or performing any maintenance operations.
WARNING: The user's guide must be consulted in all cases where this symbol is used on the equipment, in order to find out the
nature of the potential hazard and any actions which have to be taken.
Emergency stop
NOTE: Emergency stop is not considered to be a primary means of risk reduction for the hazards presented at a machine. All
precautions advised by the machine manufacturer, the Renishaw product documentation and health and safety literature should be
considered in determining the safety strategy for the use of this equipment.
The Renishaw system may provide the following safety categories, to standard EN ISO 13849, according to the type of servo amplifier fitted:-
SPA2-2: Category 2
The choice of the stop category of the emergency stop depends on the results of the user's risk assessment of the machine.
The emergency stop system, provided within the Renishaw servo amplifiers, has provision for the integration of external actuating devices.
The user should advise Renishaw of the requirements for such devices resulting from risk assessment.
Any emergency stop devices supplied by the user must comply with the requirements of UL1054 (EN60947) or other appropriate standards.
WARNING: Risk of toppling
The unit is provided with casters to help manoeuvre it into position. Take care pushing the kiosk, especially over rough surfaces.
Push the kiosk below the mid-point or have a second person hold the unit steady as it is moved.
Once in place, the unit should be fixed to the floor using the fixing holes provided.
Kiosk workstation user's guide
www.renishaw.com
Issued 10 2022
5

Kiosk workstation environmental conditions
Indoor use IP54 (BS EN60529:1992)
Altitude Up to 2000 m
Operating temperature +10 °C to +40 °C
Storage temperature ‐20 °C to +70 °C
Relative humidity 80% maximum ﴾non‐condensing﴿ for temperatures up to +31 °C
Linear decrease to 50% at +50 °C
Kiosk workstation user's guide
www.renishaw.com
Issued 10 2022
6

Introduction
The CMM kiosk is Renishaw's offering of a workstation housing that is suitable for the more harsh situations such as the shop floor
environments. The CMM kiosk offers IP54 protection to the CMM's monitor, PC and printer.
It has been ergonomically designed for ease of interaction with the CMM, and offers mounting points for a variety of optional extras such as
MCU and part identification scanners.
This user guide documents the main details of the standard kiosk, the possible variants of how the kiosk can be installed and further
configuration options for the kiosk to the user needs. Also included are details of the periodic checks and maintenance that the user should
carry out.
Kiosk workstation user's guide
www.renishaw.com
Issued 10 2022
7

Kiosk workstation description
Dimensions
NOTE: Dimensions in mm (in).
Kiosk workstation user's guide
www.renishaw.com
Issued 10 2022
8

180° opening lockable front doors
The front and rear access doors open to 180° and are lockable with a 7 mm square key. Two keys are supplied with each unit.
Please contact your local Renishaw office if replacement keys are required.
Kiosk workstation user's guide
www.renishaw.com
Issued 10 2022
9

Power distribution
Power is distributed throughout the kiosk via a 4-way IEC connector block.
Four male to female leads are supplied with the kiosk as standard to supply power for stand configuration:
1. PC
2. Printer
3. Monitor
4. 24 V PCU for cooling fan distribution PCB
Power is supplied to the cooling fans via a 24 V distribution PCB mounted within the kiosk. A 24 V PSU transformer block, to power this PCB,
is supplied with each kiosk.
If a replacement 24 V PSU is required, please contact your local Renishaw support office.
Kiosk workstation user's guide
www.renishaw.com
Issued 10 2022
10

Installation variants
The kiosk must be restrained from toppling.
The preferred option is to use floor mounting fixings to secure the kiosk to the floor. The kick plates supplied in the kiosk kit should be
secured to the floor. Pull force on floor fixing must be a minimum of 1 KN.
If kiosk cannot be fixed to the floor using kick plates then the suitable restraints should be used to remove the risk of the kiosk toppling.
Kick plate installation overview
1. Fix the two side plates to the floor using anchors.
2. Roll the kiosk into position between the side kick plates.
Kiosk workstation user's guide
www.renishaw.com
Issued 10 2022
11

3. Fix the kiosk base to the side plates.
Kiosk workstation user's guide
www.renishaw.com
Issued 10 2022
12

4. Once attached, fix the front and rear panels in place.
NOTE: If desired the kiosk can be re-positioned and re-installed by a single engineer with no lifting equipment. Please contact the
installer to arrange reposition of the kiosk if required.
Kiosk workstation user's guide
www.renishaw.com
Issued 10 2022
13

Description Part number
Kiosk assembly A-6509-1100
MCU tray A-6509-0122
MCU docking port assembly A-1333-0026
Kick plate kit A-6509-0300
Kiosk workstation user's guide
www.renishaw.com
Issued 10 2022
14

Customer options
The kiosk can be configured in several different ways to suit the user. These include mounting options for the MCU and front or side-mounted
keyboard tray.
Lockable drawers can be installed into the lower section of the kiosk.
Kiosk workstation user's guide
www.renishaw.com
Issued 10 2022
15

Kiosk workstation maintenance
Lifting
NOTE: Lifting must only be carried out by the kiosk workstation installer. Please contact the kiosk workstation installer.
Periodic checks
It is advised to periodically check the kiosk and cable management system for damage or wear to key parts. Any visible damage or wear
should be reported to the system maintenance engineer.
User serviceable parts
The kiosk has four fans which are the only user serviceable components.
Kiosk workstation user's guide
www.renishaw.com
Issued 10 2022
16

Cooling fans
CAUTION: Ensure the cabinet is switched OFF before changing the filter.
The four kiosk fans are used to push air out of the cabinet for cooling the equipment within. Two fans are located on the top rear panel of the
kiosk and one is located on each lower side panel.
The fans have mesh filters. Renishaw recommends that these are changed every 12 months at a minimum. If the kiosk is located in an
environment with high levels of particulates in the air, the filters should be changed at more regular intervals.
Description Part number
Mesh filter replacement kit (pack of five) A-6509-0400
Cleaning
Clean the kiosk workstation with a dry, lint-free cloth.
Kiosk workstation user's guide
www.renishaw.com
Issued 10 2022
17

For worldwide contact details,
please visit our main website at
www.renishaw.com/contact
Renishaw plc
New Mills, Wotton-under-Edge
Gloucestershire, GL12 8JR
United Kingdom
T+44 (0)1453 524524
F+44 (0)1453 524901
www.renishaw.com/cmmsupport
Issued 10 2022