Makita DUB363 User manual
DUB363
EN Cordless Blower INSTRUCTION MANUAL 8
FR SOUFFLEUR SANS FIL
(ASPIRO / SOUFFLEUR (SANS FIL))
MANUEL D’INSTRUCTIONS 17
DE Gebläse (Sauger) BETRIEBSANLEITUNG 27
IT ISTRUZIONI PER L’USO 37
NL Accubladblazer GEBRUIKSAANWIJZING 47
ES MANUAL DE
INSTRUCCIONES 57
PT
MANUAL DE INSTRUÇÕES 67
DA Akku blæser BRUGSANVISNING 76
EL 85
TR KULLANMA KILAVUZU 95
1
2
1
1
2
1 2
1
2
3
2
2
1
3
1
1
1
1
1 2
33
1
2 3
3
1
2
3
1
2
2
3
1
1
2
1
4
1
2
1
2
13
4
1
2
3
4
1
2
3
1
2
5
21
3
1
1
1
1
4
3
2
1
6
1
7
8ENGLISH
SPECIFICATIONS
Model: DUB363
Capacities Air volume 0 - 13.4 m3/min
Air speed (average) 0 - 54 m/s
Air speed (max.) 0 - 65 m/s
Dimensions (L x W x H) *1 341 mm x 193 mm x 415 mm
Rated voltage D.C. 36 V
Net weight Blower *2 4.5 - 5.2 kg
Vacuum *3 6.0 - 6.6 kg
*1. Without pipes, nozzles, dust bag, shoulder strap, and battery cartridges.
shoulder strap.
*3. With suction pipe, suction nozzle, elbow pipe, dust bag and shoulder strap, and without blower pipe, end nozzle
without notice.
-
est combination, according to EPTA-Procedure 01/2014, are shown in the table.
Battery cartridge BL1815N / BL1820B / BL1830B / BL1840B / BL1850B / BL1860B
Charger DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF /
DC18SH
• Some of the battery cartridges and chargers listed above may not be available depending on your region of
residence.
WARNING: Use of any other battery cartridges
Battery adapter BAP182
Cord connected battery pack BL36120A
Portable power pack PDC01 / PDC1200
• The cord connected power source(s) listed above may not be available depending on your region of residence.
• Before using the cord connected power source, read instruction and cautionary markings on them.
The followings show the symbols which may be used
for the equipment. Be sure that you understand their
meaning before use.
Take particular care and attention.
Read instruction manual.
Keep hands away from rotating parts.
Long hair may cause entanglement
accident.
Keep bystanders away.
Wear eye and ear protection.
Do not expose to moisture.
9ENGLISH
Ni-MH
Li-ion
Only for EU countries
Due to the presence of hazardous com-
ponents in the equipment, waste electrical
and electronic equipment, accumulators
and batteries may have a negative impact
on the environment and human health.
Do not dispose of electrical and electronic
appliances or batteries with household
waste!
In accordance with the European Directive
on waste electrical and electronic equip-
ment and on accumulators and batteries
and waste accumulators and batteries,
as well as their adaptation to national law,
waste electrical equipment, batteries and
accumulators should be stored separately
and delivered to a separate collection point
for municipal waste, operating in accor-
dance with the regulations on environmen-
tal protection.
This is indicated by the symbol of the
crossed-out wheeled bin placed on the
equipment.
Guaranteed sound power level according
to EU Outdoor Noise Directive.
Sound power level according to Australia
NSW Noise Control Regulation
The machine is intended for blowing and vacuuming.
The typical A-weighted noise level determined accord-
ing to EN50636-2-100:
Sound pressure level (LpA) : 84.8 dB(A)
Uncertainty (K) : 1.3 dB(A)
Sound power level (LWA) : 94.9 dB (A)
Uncertainty (K) : 0.3 dB(A)
NOTE: The declared noise emission value(s) has
been measured in accordance with a standard test
method and may be used for comparing one tool with
another.
NOTE: The declared noise emission value(s)
may also be used in a preliminary assessment of
exposure.
WARNING:
WARNING:
WARNING: -
The vibration total value (tri-axial vector sum) deter-
mined according to EN50636-2-100:
Work mode: operation without load (blowing)
Vibration emission (ah) : 2.5 m/s2or less
Uncertainty (K) : 1.5 m/s2
Work mode: operation without load (vacuuming)
Vibration emission (ah) : 2.5 m/s2or less
Uncertainty (K) : 1.5 m/s2
NOTE: The declared vibration total value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.
WARNING:
WARNING: -
For European countries only
The EC declaration of conformity is included as Annex A
to this instruction manual.
SAFETY WARNINGS
WARNING:
Failure to follow the warnings and
-
1.
2.
-
3. -
4.
10 ENGLISH
1.
2.
3.
-
-
4.
5.
Non-skid,
closed-toed safety boots and shoes will reduce the
6.
Protective equipment such
as a dust mask, non-skid safety shoes, hard hat or
hearing protection used for appropriate conditions
1.
•
•
•
•
•
2.
3.
4.
5.
6.
7.
-
8. -
9.
10.
11.
•
-
•
•
12.
13.
14.
15.
16.
17.
-
18.
19.
20.
21. -
22. -
1.
2.
3.
11 ENGLISH
4.
5.
6.
7.
1.
A charger that is suitable for
when used with another battery pack.
2. -
Use of any other battery
3.
Shorting the battery termi-
4.
-
irritation or burns.
5. -
may exhibit unpredictable behaviour resulting in
6.
-
perature above 130 °C may cause explosion.
7.
-
Charging improperly or at temperatures
1.
The cell may explode. Check with local codes for
possible special disposal instructions.
2.
Released electrolyte is corrosive and may cause
damage to the eyes or skin. It may be toxic if
swallowed.
3.
4.
5.
6.
Water entering the tool will increase the risk
of electric shock.
1.
This will ensure that the safety of the power
tool is maintained.
2. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
WARNING:
1.
-
2.
or explosion.
3.
4.
-
5.
(1) -
(2) -
(3)
6. -
7.
8.
Such conduct may result in a
9.
10.
-
For commercial transports e.g. by third parties,
forwarding agents, special requirement on pack-
aging and labeling must be observed.
12 ENGLISH
For preparation of the item being shipped, consult-
ing an expert for hazardous material is required.
Please also observe possibly more detailed
national regulations.
battery in such a manner that it cannot move
around in the packaging.
11.
12.
Installing the batteries to
-
sive heat, explosion, or leak of electrolyte.
13.
14.
-
15. -
16.
It may result in poor performance or
breakdown of the tool or battery cartridge.
17.
-
It may result in a malfunction or
breakdown of the tool or battery cartridge.
18.
CAUTION:
Use of non-genuine Makita batteries, or batteries that
have been altered, may result in the battery bursting
also void the Makita warranty for the Makita tool and
charger.
1.
2. -
3. -
4.
5.
ASSEMBLY
CAUTION:
NOTICE:
Otherwise,
the machine does not work.
and nozzle
Attach the blower pipe to the main unit.
Insert the blower pipe into the main unit with the bolt
using the hex wrench.
Bolt Blower pipe
Align the protrusion on the blower pipe with the
groove on the end nozzle, then attach the end nozzle to
the blower pipe, and then turn the end nozzle to lock it
into place.
End nozzle Blower pipe
To remove the blower pipe and end nozzle, perform the
installation procedure in reverse.
NOTE: The length of the nozzle can be changed by
End nozzle Blower pipe
Optional accessory
nozzle, and then turn it to lock it into place.
Flat nozzle Extension nozzle End
nozzle
to the blower pipe.
Flat nozzle Extension nozzle Blower
pipe
the installation procedure in reverse.
Optional accessory
The gutter nozzle can be installed on the blower. The
adapter pipe designed exclusively for this model is
required to install the gutter nozzle.
For more details, refer to the instruction manual pro-
vided with the gutter nozzle.
13 ENGLISH
CAUTION:
If the
CAUTION:
Using other shoulder
CAUTION: -
If you put on the shoulder strap included in the
machine package and the shoulder harness of the
backpack-type power supply at the same time,
removing the machine or backpack-type power supply
band, ask Makita Authorized Service Centers.
Attach the hooks of the shoulder strap to the machine
Hook
The shoulder strap features a means of quick release.
Simply squeeze the sides of the buckle to release the
machine from the shoulder strap.
Buckle
Buckle
CAUTION:
CAUTION:
-
and nozzle
Optional accessory
Align the triangle mark on the suction nozzle with
that on the suction pipe, and then insert the suction
nozzle into the suction pipe until the latch on the nozzle
snaps into place.
Suction nozzle Suction pipe Triangle
mark
Loosen the bolt on the fan cover using the hex
wrench, and open the fan cover.
Bolt Fan cover Hex wrench
Align the triangle mark on the suction pipe
with mark on the main unit, and then attach the
suction pipe to the main unit.
Suction pipe Triangle mark mark
Turn the suction pipe clockwise so that the bolt
on the pipe is aligned with the hole on the main unit,
secure the pipe to the main unit.
Suction pipe Bolt
To remove the suction pipe and nozzle, perform the
installation procedure in reverse.
Optional accessory
Insert the elbow pipe into the dust bag and tighten
Dust bag Elbow pipe Belt
Attach the elbow pipe to the main unit.
Insert the elbow pipe into the main unit with the bolt
using the hex wrench.
Bolt Elbow pipe
Attach the hook of the dust bag to the sub handle
Hook Sub handle
Attach the hooks of the shoulder strap to the carry
Make sure that the buckle is on the carry handle side.
Hook Carry handle Sub handle
Buckle
To remove the dust bag and elbow pipe, perform the
installation procedure in reverse.
When installing the small dust bag, open the fastener,
then insert the elbow pipe into the dust bag, and then
elbow pipe.
Fastener Dust bag Belt Elbow
pipe
14 ENGLISH
FUNCTIONAL DESCRIPTION
CAUTION:
CAUTION:
CAUTION:
-
Failure to hold the machine and the
your hands and result in damage to the machine and
CAUTION:
If not,
it may accidentally fall out of the machine, causing
CAUTION:
If the cartridge does not slide in easily, it is
not being inserted correctly.
Red indicator Button Battery cartridge
To remove the battery cartridge, slide it from the machine
while sliding the button on the front of the cartridge.
To install the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Insert it all the way until it locks in place
with a little click. If you can see the red indicator on the
upper side of the button, it is not locked completely.
Only for battery cartridges with the indicator
Indicator lamps Check button
Press the check button on the battery cartridge to indi-
cate the remaining battery capacity. The indicator lamps
light up for a few seconds.
75% to 100%
50% to 75%
25% to 50%
0% to 25%
Charge the
battery.
The battery
may have
malfunctioned.
NOTE: Depending on the conditions of use and the
from the actual capacity.
NOTE:
the battery protection system works.
The machine is equipped with a machine/battery
power to the motor to extend machine and battery life.
The machine will automatically stop during operation if
the machine or battery is placed under one of the fol-
lowing conditions:
When the machine or battery is operated in a manner
that causes it to draw an abnormally high current, the
machine automatically stops and the lamp for mode
1 blinks in green. In this situation, turn the machine
to become overloaded. Then turn the machine on to
restart.
When the machine or battery is overheated, the
machine stops automatically and the lamp for mode 1
lights up in red. In this case, let the machine and battery
cool down before turning the machine on again.
When the battery capacity is not enough, the machine
stops automatically and the lamp for mode 1 blinks in
red. In this case, remove the battery from the machine
and charge the battery.
WARNING:
To turn on the machine, press the main power switch.
The lamps for mode 1 and mode 2 light up in green. To
(1) Lamp for mode 1 (2) Lamp for mode 2
(3) Main power switch
You can use the machine in the vacuuming mode. In the
vacuuming mode, the suction volume becomes smaller
than in the normal mode.
When you turn on the machine, the machine starts up in
the normal mode. To use the machine in the vacuuming
mode, press the main power switch when the machine
lamp for mode 1 lights up in green. When you press the
main power switch again, the machine returns to the
normal mode, and the lamps for mode 1 and mode 2
light up in green.
15 ENGLISH
NOTE: The lamp for mode 1 blinks in green if the
machine is operated under unoperatable conditions.
The lamp blinks in one of the following conditions.
• The switch trigger is pulled, when the bolt on the
or the bolt on the blower pipe or elbow pipe is
• The machine is turned on, when the control
while you are pulling the switch trigger.
NOTE:
function. To avoid unintentional start up, the main
power switch will automatically shut down when the
switch trigger is not pulled for a certain period after
the main power switch is turned on.
WARNING: -
Switch trigger
To start the machine, simply pull the switch trigger. The
speed is increased by increasing pressure on the switch
trigger. Release the switch trigger to stop.
The cruise control function allows the operator to main-
tain a constant speed without pulling the trigger. To
increase the speed, turn the control lever forward. To
decrease the speed, turn the control lever backward.
Control lever
When not in use, store the hex wrench as illustrated to
keep it from being lost.
Hex wrench
If you turn on the machine while pulling the switch trig-
release the switch trigger and return the control lever
fully, and then turn on the machine.
The machine is equipped with the electronic function for
easy operation.
• Constant speed control
The speed control function provides the constant
rotation speed regardless of load conditions.
OPERATION
CAUTION:
Sand or dust may
enter from suction inlet and cause a malfunction or
CAUTION:
blowing operation by moving it around slowly. When blow-
ing around building, big stone or vehicle, direct the nozzle
away from them. When performing an operation in a
corner, start from the corner and then move to wide area.
CAUTION:
CAUTION:
CAUTION:
CAUTION:
CAUTION:
NOTICE:
Otherwise, a malfunction may occur.
NOTICE:
Otherwise, a malfunction may occur.
NOTICE: -
Put the shoulder strap on the shoulder as shown
Shoulder strap Carry handle Sub
handle Dust bag
Hold the carry handle with your right hand and the
sub handle with the other hand.
Make sure that the buckle is on the front side.
Buckle
trigger so that the suction force is appropriate for the
work location and conditions.
16 ENGLISH
MAINTENANCE
CAUTION:
To maintain product SAFETY and RELIABILITY,
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
one dipped in soapy water and wrung out.
NOTICE:
Remove dust or dirt from the suction inlets.
Suction inlet
TROUBLESHOOTING
-
ual, do not attempt to dismantle the machine. Instead, ask Makita Authorized Service Centers, always using Makita
replacement parts for repairs.
Motor does not run. Battery cartridge is not installed. Install the battery cartridge.
Battery problem (under voltage)
replace battery.
For blower
The blower pipe is not attached.
The fan cover is not closed.
Attach the blower pipe, and then tighten the bolt.
Close the fan cover, and then tighten the bolt.
The elbow pipe or suction pipe is not
attached.
Attach the elbow pipe or suction pipe, and then
tighten the bolt.
The drive system does not work
correctly.
Ask your local authorized service center for repair.
Motor stops running after a little use. Battery's charge level is low.
replace battery.
Overheating. Stop using the machine to allow it to cool down.
The machine does not reach the
maximum speed.
Battery is installed improperly. Install the battery cartridge as described in this
manual.
Battery power is dropping.
replace battery.
The drive system does not work
correctly.
Ask your local authorized service center for repair.
Abnormal vibration:
stop the machine immediately!
The drive system does not work
correctly.
Ask your local authorized service center for repair.
Motor cannot stop:
Remove the battery immediately!
Electric or electronic malfunction. Remove the battery and ask your local authorized
service center for repair.
OPTIONAL
ACCESSORIES
CAUTION:
-
The use of any other
accessories or attachments might present a risk of
for its stated purpose.
If you need any assistance for more details regard-
ing these accessories, ask your local Makita Service
Center.
• Vacuum kit
• Extension nozzle
• Flat nozzle
• Gutter nozzle
• Adapter pipe
• Shoulder strap
• Small dust bag
• Makita genuine battery and charger
NOTE: Some items in the list may be included in the
product package as standard accessories. They may
17 FRANÇAIS
SPÉCIFICATIONS
Modèle : DUB363
Capacités Volume d’air 0 - 13,4 m3/min
Vitesse de l’air (moyenne) 0 - 54 m/s
Vitesse de l’air (max.) 0 - 65 m/s
Dimensions (L x P x H)*1 341 mm x 193 mm x 415 mm
Tension nominale 36 VCC
Poids net 4,5 - 5,2 kg
Aspirateur*3 6,0 - 6,6 kg
*1. Sans tuyaux, buses, sac à poussière, bandoulière et batteries.
-
sière et bandoulière.
-
trémité et buse plate.
plus lourde, conformément à la procédure EPTA 01/2014, sont indiquées dans le tableau.
Batterie BL1815N / BL1820B / BL1830B / BL1840B / BL1850B / BL1860B
Chargeur DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF /
DC18SH
• Certains chargeurs et batteries répertoriés ci-dessus peuvent ne pas être disponibles selon la région où vous
résidez.
AVERTISSEMENT : L’utilisation
d’autres batteries et chargeurs peut provoquer des blessures et/ou un incendie.
Adaptateur de Batterie BAP182
Batterie connectée par cordon BL36120A
Support d’alimentation portable PDC01 / PDC1200
• La ou les sources d’alimentation connectées par cordon répertoriées ci-dessus peuvent ne pas être dispo-
nibles selon la région où vous résidez.
• Avant d’utiliser la source d’alimentation connectée par cordon, lisez les instructions et les avertissements
inscrits dessus.
Vous trouverez ci-dessous les symboles susceptibles
d’être utilisés pour l’appareil. Veillez à comprendre leur
Veuillez être prudent et rester attentif.
Lire le mode d’emploi.
Gardez vos mains à l’écart des pièces en
rotation.
Les cheveux longs risquent de se prendre
dans les pièces en mouvement.
Tenez les personnes à l’écart.
Porter des lunettes de protection et un
serre-tête antibruit.
Ne pas exposer à l’humidité.
18 FRANÇAIS
Ni-MH
Li-ion
Pour les pays de l’Union européenne
uniquement
En raison de la présence de composants
dangereux dans l’équipement, les déchets
d’équipements électriques et électro-
niques, les accumulateurs et les batteries
peuvent avoir un impact négatif sur l’envi-
ronnement et la santé humaine.
électroniques ou les batteries avec les
ordures ménagères !
Conformément à la directive européenne
relative aux déchets d’équipements élec-
triques et électroniques et aux déchets
d’accumulateurs et de batteries, ainsi qu’à
son adaptation à la législation nationale,
les déchets d’équipements électriques,
les batteries et les accumulateurs doivent
être collectés séparément et déposés
dans un point de collecte distinct pour
déchets urbains, conformément aux régle-
mentations en matière de protection de
l’environnement.
Cela est indiqué par le symbole de la pou-
belle à roulettes barrée sur l’équipement.
Niveau de puissance sonore garanti selon
la directive européenne sur le bruit dans
l’environnement.
Niveau de puissance sonore selon la
réglementation australienne NSW sur le
contrôle du bruit
Niveau de bruit pondéré A typique, déterminé selon
EN50636-2-100 :
Niveau de pression sonore (LpA) : 84,8 dB (A)
Incertitude (K) : 1,3 dB (A)
Niveau de puissance sonore (LWA ) : 94,9 dB (A)
Incertitude (K) : 0,3 dB (A)
NOTE : La ou les valeurs d’émission de bruit décla-
rées ont été mesurées conformément à la méthode
de test standard et peuvent être utilisées pour com-
parer les outils entre eux.
NOTE : La ou les valeurs d’émission de bruit décla-
rées peuvent aussi être utilisées pour l’évaluation
préliminaire de l’exposition.
AVERTISSEMENT :
AVERTISSEMENT :
AVERTISSEMENT :
Valeur totale de vibrations (somme de vecteur triaxial)
déterminée selon EN50636-2-100 :
Émission de vibrations (ah) : 2,5 m/s2ou moins
Incertitude (K) : 1,5 m/s2
Mode de travail : fonctionnement à vide (aspiration)
Émission de vibrations (ah) : 2,5 m/s2ou moins
Incertitude (K) : 1,5 m/s2
NOTE : La ou les valeurs de vibration totales décla-
rées ont été mesurées conformément à la méthode
de test standard et peuvent être utilisées pour com-
parer les outils entre eux.
NOTE : La ou les valeurs de vibration totales décla-
rées peuvent aussi être utilisées pour l’évaluation
préliminaire de l’exposition.
AVERTISSEMENT :
AVERTISSEMENT :
Pour les pays européens uniquement
La déclaration de conformité CE est fournie en Annexe
A à ce mode d’emploi.
CONSIGNES DE SÉCURITÉ
AVERTISSEMENT :
Il
y a risque d’électrocution, d’incendie et/ou de graves
blessures si les mises en garde et les instructions ne
sont pas respectées.
-
1.
19 FRANÇAIS
2. -
3. -
4. -
1.
2.
3.
-
4.
5.
Porter des bottes ou des chaussures
de sécurité fermées et antidérapantes permet de
réduire le risque de blessure.
6. -
-
Les équipements de sécurité tels que les
masques contre les poussières, les chaussures
de sécurité antidérapantes, les casques ou les
protecteurs d’oreilles utilisés pour les conditions
appropriées réduiront les blessures.
1. -
•
•
• -
•
•
2.
3.
4.
5.
6.
-
7. -
-
8. -
9.
10.
11.
•
•
•
12.
13. -
14.
15.
-
20 FRANÇAIS
16.
17.
18.
19. -
20.
21. -
-
22.
1.
2.
3.
4. -
-
5.
6.
7. -
1. -
Un chargeur qui
présenter un risque d’incendie s’il est utilisé avec
un autre type de batterie.
2.
L’utilisation
de toute autre batterie peut présenter un risque de
blessure et d’incendie.
3.
-
Court-circuiter les bornes d’une batterie
entre elles peut provoquer des brûlures ou un
incendie.
4.
Le
liquide s’échappant de la batterie peut provoquer
une irritation ou des brûlures.
5.
Une batterie endom-
imprévisible susceptible d’entraîner un incendie,
une explosion ou des blessures.
6.
L’exposition au feu
ou à une température supérieure à 130 °C peut
provoquer une explosion.
7.
Une charge incorrecte ou à une
température en dehors de la plage indiquée peut
endommager la batterie et augmenter le risque
d’incendie.
1.
L’élément de la pile pourrait exploser. Consultez
les codes locaux pour de possibles instructions de
mise au rebut spéciales.
2.
L’électrolyte qui s’échappe de la batterie est cor-
rosif et peut irriter la peau ou les yeux. Il peut être
toxique en cas d’ingestion.
3.
4.
5.
6.
Le risque d’électrocution
augmente si de l’eau pénètre dans l’outil.
1.
La sécurité de l’outil élec-
trique sera ainsi préservée.
2. -
-
tué uniquement par le fabricant ou un dépanneur
agréé.
CONSERVEZ CES
Other manuals for DUB363
9
This manual suits for next models
2
Table of contents
Languages:
Other Makita Blower manuals
Makita
Makita DUB184RF User manual
Makita
Makita M4000 User manual
Makita
Makita BHX250 User manual
Makita
Makita BUB182Z User manual
Makita
Makita BUB142 User manual
Makita
Makita UB100D User manual
Makita
Makita DUB143 User manual
Makita
Makita DUB143 User manual
Makita
Makita DUB361 User manual
Makita
Makita CBU01 User manual
Makita
Makita BHX2500 User manual
Makita
Makita PM7651H User guide
Makita
Makita DUB362 User manual
Makita
Makita PM7651H User guide
Makita
Makita DUB363 User manual
Makita
Makita RBL250 User guide
Makita
Makita ADSA01 User manual
Makita
Makita UB141DZ User manual
Makita
Makita UB121D User manual
Makita
Makita UB003C User manual
Popular Blower manuals by other brands
Weed Eater
Weed Eater EBV 215 instruction manual
Toro
Toro Flex-Force Power System 51825T Operator's manual
Elektor
Elektor SD Series Operating and assembly instructions
Kenmore
Kenmore 2335994690 Use and care/installation manual
TURFCO
TURFCO Torrent Operators manual & parts lists
LawnMaster
LawnMaster BV1211 Operator's manual