Malaguti MISSION 125 User manual

MISSION 125
MISSION 200
INSTRUCTION MANUAL
ENGLISH

2Mission 125 / 200
TABLE OF CONTENTS � � � � � � � � � � � � 2
INTRODUCTION � � � � � � � � � � � � � � � � 3
Welcome to Malaguti. . . . . . . . . . . . . . 3
EXPLANATION � � � � � � � � � � � � � � � � � 4
INSTRUMENTS & OPERATION � � � � � � 5
Ignition lock . . . . . . . . . . . . . . . . . . . . 5
Instrument cluster. . . . . . . . . . . . . . . . 5
Left handlebar switch . . . . . . . . . . . . . 6
Right handlebar switch . . . . . . . . . . . . 7
Handbrake lever left . . . . . . . . . . . . . . 7
Handbrake lever right . . . . . . . . . . . . . 7
Fuel filler cap. . . . . . . . . . . . . . . . . . . . 7
Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Catalyst. . . . . . . . . . . . . . . . . . . . . . . . 8
Seat . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Storage compartment . . . . . . . . . . . . . 9
Helmet and luggage hooks . . . . . . . . . 9
USB charging port. . . . . . . . . . . . . . . 10
Seitenständer . . . . . . . . . . . . . . . . . . 10
Main stand . . . . . . . . . . . . . . . . . . . . 10
DRIVING OPERATION � � � � � � � � � � � 11
Start engine . . . . . . . . . . . . . . . . . . . 11
Drive off . . . . . . . . . . . . . . . . . . . . . . 11
Accelerate & Decelerate . . . . . . . . . . 11
Brakes . . . . . . . . . . . . . . . . . . . . . . . 12
Parking . . . . . . . . . . . . . . . . . . . . . . . 12
First maintenance . . . . . . . . . . . . . . . 12
MAINTENANCE & SERVICING � � � � � � 13
Bordwerkzeug . . . . . . . . . . . . . . . . . . 13
Spark plug . . . . . . . . . . . . . . . . . . . . 13
Motor oil. . . . . . . . . . . . . . . . . . . . . . 14
Air filter. . . . . . . . . . . . . . . . . . . . . . . 15
ECU . . . . . . . . . . . . . . . . . . . . . . . . . 15
Throttle cable clearance. . . . . . . . . . . 15
Tyres. . . . . . . . . . . . . . . . . . . . . . . . . 16
Rims. . . . . . . . . . . . . . . . . . . . . . . . . 17
Brakes . . . . . . . . . . . . . . . . . . . . . . . 17
Lubricate brake lever. . . . . . . . . . . . . 18
Bowden cables . . . . . . . . . . . . . . . . . 18
Throttle grip and throttle cable. . . . . . 19
Side and main stand . . . . . . . . . . . . . 19
Telescopic suspension fork . . . . . . . . 19
Steering . . . . . . . . . . . . . . . . . . . . . . 19
Wheel bearing. . . . . . . . . . . . . . . . . . 19
Battery . . . . . . . . . . . . . . . . . . . . . . . 20
Fuses . . . . . . . . . . . . . . . . . . . . . . . . 20
FAULT DETECTION � � � � � � � � � � � � � 21
Fault identification list . . . . . . . . . . . . 21
TECHNICAL SPECIFICATIONS � � � � � � 22
Technical data - Mission 125 . . . . . . . 22
Technical data - Mission 200 . . . . . . . 25
NOTES � � � � � � � � � � � � � � � � � � � � � 28
TABLE OF CONTENTS

Mission 125 / 200 3
WELCOME TO MALAGUTI
Thank you for choosing this vehicle. This model is safely designed, durably manufactured and excellent for
daily road use. The unique vehicle design represents your excellent personal taste.
This owner's manual explains the correct and safe use of the vehicle and simple inspections.
If you have any questions regarding the operation or maintenance of the vehicle, please contact your authorised
dealer.
Please read the owner's manual carefully.
INTRODUCTION

4Mission 125 / 200
These operating instructions use the following symbols to draw attention to important information:
WARNING
Is a WARNING that must be followed! Failure to do so may result in serious injury or death to the rider or
others involved.
NOTE
Is a NOTICE of important information which, if not followed, may result in damage to the vehicle.
NOTE
• The owner's manual should always be carried with the vehicle so that it is available for entries during
maintenance by your authorised dealer. When selling the vehicle, please hand over the operating
instructions with the vehicle to the new owner.
• The Owner's Manual contains all important information about the vehicle. However, the manufacturer
is constantly making improvements which may lead to deviations from these operating instructions.*
Please contact your authorised dealer directly with any questions.
WARNING
• For your own safety, please read these operating instructions carefully before operating the vehicle.
• Do not drive until you are fully familiar with the vehicle.
• Regular inspections and maintenance as well as good driving skills guarantee safe driving and the
reliability of this vehicle.
*Product and specifications are subject to change without notice.
EXPLANATION

Mission 125 / 200 5
IGNITION LOCK
The ignition lock controls the ignition and lighting
system and is used to lock the steering and open the
seat. The positions are described below.
Ignition switched on -
All electrical circuits are supplied, the engine can be
started and the key cannot be removed.
Ignition switched off -
All electrical systems are switched off. The key can
be removed.
Steering lock -
The steering is locked and all electrical systems are
switched off. The key can be removed.
Locking the handlebars
• Turn the handlebars all the way to the left.
• Insert the key into the ignition lock.
• While applying pressure to the key, turn it anti-
clockwise into the Position. If the lock does
not engage immediately, move the handlebar
back and forth slightly.
• Remove the key.
Unlock handlebars
• Insert the key into the ignition lock.
• Turn the key clockwise to the Position. If
the lock does not release immediately, move
the handlebar back and forth slightly.
Tamper protection
When the key is removed, you can activate the tamper
protection for the ignition lock by pressing the SHUT
button. This closes the keyhole with a metal flap. To
open the flap, insert the hexagonal key on the head
of the ignition key into the appropriate shape and
turn it clockwise.
Opening the seat
Insert the key into the ignition lock and turn it either
anticlockwise or clockwise without pressure and the
seat will unlock.
Open fuel tank
Insert the key into the ignition lock and turn it
clockwise with pressure and the tank unlocks.
INSTRUMENT CLUSTER
12345678
101112131415
9
1� Engine control light
When you switch on the ignition, the lamp lights up.
It disappears after you start the engine. If your vehicle
detects a fault in the system, the warning light comes
on. Contact a dealer.
2� Fuel gauge
The fuel gauge shows how much fuel is left in the fuel
tank. When the tank is full, the indicator is near "F"
(Full). When the tank is emptying, the indicator moves
towards "E" (Empty).
3� Fuel warning light
This light indicates that the fuel reserve is active. If the
fuel symbol flashes, please refuel as soon as possible.
4� Oil pressure warning light
This indicator lights up when the oil pressure is
INSTRUMENTS & OPERATION

6Mission 125 / 200
abnormal. In this case, please stop the vehicle
immediately to avoid damage to the engine..
5� Coolant temperature warning
light
This indicator lights up when the coolant temperature
is too high. Stop the vehicle and allow the engine
to cool down. Check the cooling system including
coolant and cooling fan.
6� Rev counter
The rev counter shows the current number of the
engine.
7� Time display
The current time is displayed here.
• Press the RESET button for 3 seconds to enter
the time setting mode (12-hour system).
• The hour position flashes.
• Briefly press the RESET button for hour +1.
• Briefly press the SELECT button to switch to the
minute position.
• Briefly press the RESET button for minute +1.
• Briefly press the SELECT button to exit the time
setting mode.
8� Battery voltage
Briefly press the RESET button to switch between the
time and the battery voltage. If the battery symbol
lights up, the current battery voltage is displayed.
9� High beam indicator light
Illuminates when the high beam is switched on.
10� Indicator lamp
This indicator light flashes when the left or right
indicator lights are activated.
11� Odometer
Either the total odometer reading ODO or the trip
odometer reading TRIP 1 or TRIP 2 is displayed here.
Switching is possible by briefly pressing the SELECT
button. If the trip odometer reading TRIP 1 or TRIP
2 is displayed, it can be reset to zero by pressing the
RESET button for 3 seconds.
12� Speed display
The current driving speed is displayed here.
13� Select button
This key can be used to select various functions on the display.
14� RESET button
This button can be used to make various settings on
the display.
15� ABS indicator light
When you switch on the ignition, the ABS control lamp
lights up. As soon as you start driving and reach a
driving speed of approx. 5 km/h, the ABS control light
goes out. If the lamp lights up while driving, the ABS is
not working. In this case, contact your dealer.
LEFT HANDLEBAR SWITCH
1
3
2
4
1� Headlight flasher
Press the button to activate the headlight flasher.
2� Indicator
To turn right, slide the indicator switch to the right.
To turn left, slide the indicator switch to the left. To
switch off the indicator, push the switch back to the
centre position.
3� High beam and low beam
By changing the switch position, you can switch
between high beam and low beam.
4� Horn
Press the button to activate the horn.
INSTRUMENTS & OPERATION

Mission 125 / 200 7
RIGHT HANDLEBAR SWITCH
1
2
1� Emergency stop switch (motor)
In the switch position the engine can be started
or it is already running. By changing the switch
position to a running engine goes out and the
engine cannot be started.
2� Electric starter
To start the vehicle, operate the starter motor .
HANDBRAKE LEVER LEFT
The brake lever for the rear brake is located on the
handlebar on the left. To brake, pull the lever towards
the handlebar.
HANDBRAKE LEVER RIGHT
The brake lever for the front brake is located on
the handlebar on the right. To brake, pull the lever
towards the handlebar.
FUEL FILLER CAP
1
The fuel filler cap (1) is located under the handlebar.
Open the fuel filler cap with the ignition key.
Open fuel filler cap
• Insert the key into the ignition lock and turn it
clockwise with pressure and the tank unlocks.
The fuel filler cap can be opened.
INSTRUMENTS & OPERATION

8Mission 125 / 200
FUEL
Make sure that there is enough fuel in the tank. Fill
the petrol tank to the lower edge of the filler neck at
the most.
Unleaded petrol RON/ROZ min� 95
E5 E10
!! ATTENTION !!
BIOETHANOL E15-E100 IS NOT SUITABLE FOR
WARNING
• Do not overfill the petrol tank, otherwise petrol
may leak out.
• Fuel must never run over hot vehicle parts such
as the engine or exhaust. This could ignite!
NOTE
Wipe away spilled fuel with a suitable cloth, as
painted surfaces and plastic parts may be damaged.
CATALYST
This model is equipped with a catalytic converter in
the exhaust system.
WARNING
The exhaust system is very hot during and
immediately after operation of the vehicle.
The exhaust system must cool down before
maintenance work is carried out.
NOTE
Follow the safety instructions below to avoid fire
and damage to property.
• Only use unleaded petrol.
• Leaded petrol will cause irreparable damage
to the catalytic converter.
• Do not park the vehicle directly on dry grass,
for example.
• Do not let the engine idle for too long.
INSTRUMENTS & OPERATION

Mission 125 / 200 9
SEAT
Open the seat
• Place the vehicle on the main stand.
• Insert the key into the ignition lock and turn the
key anticlockwise or clockwise without pushing
it in.
• The lock unlocks automatically and the bench
seat pops up.
• Fold up the seat bench.
Close the seat
Fold down the seat and press it shut with the ball of
your hand directly above the lock.
NOTE
If you close or slam the bench seat with force,
parts may be damaged. Make sure that the seat is
properly closed before driving or when you park
the vehicle.
STORAGE COMPARTMENT
1
The storage compartment (1) is located under the
seat.
NOTE
Do not exceed the maximum load of 2.5 kg. The
storage compartment heats up due to the sun and
the engine. The inside of the storage compartment
can get wet during vehicle cleaning. Therefore, do
not store any sensitive objects in it. Do not store any
valuables in the storage compartment.
HELMET AND LUGGAGE HOOKS
NOTE
Do not exceed the maximum load of 1 kg.
INSTRUMENTS & OPERATION

10 Mission 125 / 200
USB CHARGING PORT
1
The USB charging port (1) is located under the
handlebar. Open the fuel filler cap with the ignition
key.
SEITENSTÄNDER
1
The side stand (1) is located on the left side of the
vehicle. Fold out the side stand with your foot and
park the vehicle.
NOTE
When the side stand is folded out, the engine does
not start. A running engine stops when the side
stand is folded out. Do not use the side stand for
parking on a slope or on soft or uneven ground.
MAIN STAND
1
The main stand (1) is located under the vehicle.
To place the vehicle on the main stand, step on the
operating lever on the left side of the vehicle with
your foot, then pull the vehicle onto the stand by the
grab handle and handlebar.
Make sure that your vehicle is well and stably parked
to avoid tipping over.
INSTRUMENTS & OPERATION

Mission 125 / 200 11
START ENGINE
WARNING
• Before you start driving, first familiarise
yourself with all the controls and functions.
Contact your authorised dealer with any
questions.
• Do not start the engine in closed rooms. The
exhaust gases are toxic and inhalation can
lead to unconsciousness or death within a
very short time.
Starting with the electric starter
• Turn the ignition key to the ON position.
• Pull the right brake lever, otherwise the vehicle
will not start.
• Operate the starter for a few seconds.
NOTE
• Please do not hold the starter for longer than 5
seconds, otherwise it will be damaged.
• If the engine does not start immediately when
the starter is pressed, wait a few seconds before
trying to start again. Each starting process should
be as short as possible to preserve the battery
and the starter.
Starting with the Kickstarter (if
available)
• Turn the ignition key to the ON position.
• Pull the right brake lever, otherwise the vehicle
will not start.
• Push the kick starter lever down with your foot
until you feel a noticeable resistance.
• Then push the kick starter down evenly and
forcefully.
NOTE
The vehicle must be started with the kick starter at regular
intervals (recommendation: weekly), otherwise the grease
of the kick starter gearing can gum up and the kick starter
can no longer be operated.
DRIVE OFF
• Pull the brake lever with your left hand and hold
the luggage carrier with your right hand. Then
push the vehicle off the main stand.
• Sit on the seat and adjust the rear-view mirrors.
• Set the indicator.
• Pay attention to the traffic and slowly turn the
throttle grip (right) to drive off.
• Switch off the indicator.
ACCELERATE & DECELERATE
The speed is also controlled with the throttle grip.
• To accelerate, turn the handle in direction (a).
• To decelerate, turn the handle in direction (b).
DRIVING OPERATION

12 Mission 125 / 200
BRAKES
Front and rear brake
• Turn the throttle grip fully in direction (b).
• Pull the front and rear brakes at the same time,
increase the brake pressure evenly.
WARNING
• Avoid abrupt or sharp braking. You could
skid.
• Level crossings, tram tracks, steel plates in
construction areas and manhole covers are
particularly dangerous when wet. Reduce
your speed and cross these hazards with
extreme caution.
• Remember that braking is more difficult on
wet roads.
• When going downhill, please drive slowly.
Braking when going downhill is particularly
difficult.
PARKING
P
To park, switch off the engine using the ignition lock, place
the vehicle on the main stand or side stand. Remove the
key.
FIRST MAINTENANCE
Maintenance after the first 1,000 km is the most
important. By then, all parts have been run in.
Therefore, all parts and components must be
readjusted and all fasteners tightened during this
maintenance. Careful maintenance after the first
1,000 km ensures the best performance of your
vehicle and prolongs its life.
NOTE
Maintenance at 1,000 km must be carried out
according to the contents given in the section
"Service and maintenance".
DRIVING OPERATION

Mission 125 / 200 13
BORDWERKZEUG
The maintenance information and the on-board tools
supplied help to carry out preventive maintenance and
minor repairs. However, certain maintenance requires
special tools.
HINWEIS
• The safety and condition of the vehicle
depend on proper maintenance, regular
inspections and the necessary adjustment
and lubrication of various components.
• On the following pages you will find the
relevant instructions.
• Maintenance, replacement or repair of the
exhaust system may only be carried out by
an authorised specialist dealer in accordance
with the respective legal requirements.
WARNUNG
• Leave maintenance work that affects the
warranty claim or with which you are not
familiar to an authorised specialist dealer.
• Modifications to the vehicle that have not been
approved by the manufacturer can lead to a
change in performance, non-permitted exhaust
emission values and unsafe driving behaviour.
• If such modifications are carried out by the
customer without authorisation from the
manufacturer, the warranty claim will be
invalidated.
SPARK PLUG
SPARK PLUGS MISSION 125/200
Manufacturer: NGK
Model: PMR9B
Electrode gap 0.6 - 0.7 mm
Tightening torque 12 Nm
The spark plug is an important part of the engine
and is easy to check. Heat and deposits wear out
the spark plug, so it must be checked according to
the maintenance table. The spark plug also gives an
indication of the condition of the engine. The spark
plug is located on the underside of the vehicle.
Check spark plug
Remove the spark plug connector (1).
1
Unscrew the spark plug with the spark plug spanner
(2) of the on-board tool.
MAINTENANCE & SERVICING

14 Mission 125 / 200
2
Check that the insulator (3) around the centre
electrode of the spark plug is fawn. This is the ideal
colour when the vehicle is properly maintained and
operated.
3
4
NOTE
If the spark plug shows a different colour, this
could indicate a malfunction of the engine. Do not
diagnose such problems yourself. Please contact
your specialist dealer.
Check the spark plug for burning of the electrode
(4) and excessive charring or other deposits. If
necessary, replace the spark plug.
WARNING
Please note that no other spark plug model is
permitted. The use of a different spark plug model
can lead to engine damage in a short time.
Before reinserting the spark plug, check the electrode
gap and clean the spark plug with a dry cloth.
Insert the spark plug in reverse order.
WARNING
Please observe the maximum tightening torque
when inserting the spark plug.
If you have no way of checking this, leave this task to
the specialist dealer.
MOTOR OIL
ENGINE OIL MISSION 125/200
Valence (~20°C) SAE 10W/40
WARNING
The level of the engine oil must be checked each time
the tank is filled.
• Place the vehicle on the main stand, remove
the dipstick (1) and wipe it.
• Insert the dipstick (1), do not screw it in, take it
out again and check that the oil level is between
the upper (2) and lower (3) marks.
MAINTENANCE & SERVICING

Mission 125 / 200 15
NOTE
Make sure that the engine oil dipstick is properly
inserted before driving off.
AIR FILTER
The air filter must be changed according to the
maintenance table. Change the air filter more
frequently if you drive in unusually dusty or humid
environments.
Replace air filter
• Unscrew the screws of the air filter housing (1).
• Pull out the air filter.
• Replace it with a replacement filter from the
manufacturer.
• Slightly grease the air filter housing and the
contact surface for an airtight seal.
• Install the air filter.
• Screw on the air filter housing.
NOTE
• Make sure that the air filter is correctly
seated in the air filter housing and that it is
correctly closed.
• The engine must never be operated without
an air filter. Unfiltered air can immediately
cause engine damage.
ECU
ECU
The engine control unit "ECU" is an important part
of the engine and must always be set correctly.
Any manipulation can have a negative effect on
engine running and result in engine damage. Leave
maintenance and adjustment work to the specialist
dealer.
THROTTLE CABLE CLEARANCE
1
The throttle cable clearance (1) should be 2 - 6 mm.
NOTE
Regular checks of the throttle cable play and
adjustment should be carried out by your dealer.
MAINTENANCE & SERVICING

16 Mission 125 / 200
TYRES
TYRE SPECIFICATION
Tyre Pressure (Front & Rear) 2,0 bar
Tyre type Tubeless
Front rim MT 3.00 x 13
Rear rim MT 3.50 x 13
Front tyre 120/70-13 - 53P
Rear tyre 130/70-13 - 63P
For best performance, longevity and safe operation of
your vehicle, please note the following tyre information.
Tyre pressure
Tyre pressure should be checked before every
journey and corrected if necessary. Check the tyre
pressure at least every time you refuel.
WARNING
• Check tyre pressure when tyres are cold
(before driving off). Adjust tyre pressure
according to operating conditions.
• Do not overload the vehicle! The higher the
load on the vehicle, the higher the pressure on
the tyres, brakes and steering. This can lead to
damage or accidents.
• The weight distribution on the vehicle is
important for your safety and the performance
of the vehicle. Tie down your load properly and
load the heaviest loads centrally on the vehicle.
This will keep you in control of the vehicle.
Tyre inspection
1
2
3
• Tread depth
• Sidewall
• Wear indicator
WARNING
Check the condition of the tyres before every journey.
If a tyre shows cross lines (minimum tread depth), this
indicates damage. Have the tyre checked immediately
by a specialist and have the tyre replaced immediately
if necessary.
HINWEIS
The tread depth may differ depending on the country.
Observe the local regulations. The values given here
are technical values and may differ from the legal
values in your region.
WARNING
• Driving with worn tyres is illegal, reduces
stability and can lead to loss of control of
the vehicle.
• Have worn or damaged tyres replaced
immediately by your specialist dealer.
• Work on tyres and wheels is the
responsibility of your specialist dealer.
MAINTENANCE & SERVICING

Mission 125 / 200 17
RIMS
For best performance and durability and safe
operation of your vehicle, please follow the
instructions below regarding the rims.
• Check the rims for cracks and deformations
before every ride.
• Have damaged rims replaced by your specialist
dealer.
• Do not carry out any unauthorised repairs to
the rims.
• A deformed or broken rim must be replaced.
• The wheel must be balanced after a tyre change.
• An unbalanced wheel will result in poor
performance, difficult control of the vehicle and
shorten the life expectancy of the tyre.
• After changing a tyre, drive slowly at first, as the
tyre must be run in.
BRAKES
Brake lever clearance
The brake levers should have a clearance of 10-20
mm measured at the end of the lever. If this is not
the case, please contact your specialist dealer for an
inspection of the brake system.
WARNING
• A brake lever that feels soft or spongy when
braking may indicate that there is air or water in
the hydraulic system. If there is air or water in
the hydraulic system, please have it bled or the
brake fluid replaced by your dealer.
• Air or water in the hydraulic system reduces
braking performance and may cause loss of
control of the vehicle.
Brake pads
The brake pads must be checked at regular intervals.
In the best case, before every journey. The pads
have a notch that must always be visible. The wear of
the pads depends on the driving style and the road
surface. When the minimum pad thickness of 1 mm
is reached, both pads must be replaced. Leave the
replacement of the brake pads to the specialist dealer.
Worn brake pads increase the braking distance.
Brake fluid
1
MAINTENANCE & SERVICING

18 Mission 125 / 200
WARNING
Insufficient brake fluid level can lead to air
entrapment in the brake system, which reduces
braking force. Check that the brake fluid is above
the minimum mark (1) before each journey and
top up if necessary.
• A low level may also indicate worn brake pads
or a leak in the brake system.
• If the brake fluid level is low, please check the
brake pads for wear and the brake system for
leaks.
• When checking the brake fluid level, make sure
that the brake master cylinder is level. Turn the
handlebar accordingly.
• Only use high-quality brake fluid, otherwise
the rubber seals may degrade and lead to poor
braking performance.
BRAKE FLUID
Quality DOT 4
• Always top up with the same brake fluid. Mixing
can lead to chemical reactions and reduced
braking performance.
• Make sure that no water enters the brake
master cylinder when refilling. This reduces the
boiling point of the brake fluid considerably and
can lead to the formation of vapour bubbles.
• Brake fluid attacks painted surfaces and
plastic. Always wipe off overflowing brake fluid
immediately.
• As your brake pads wear, the level of brake fluid
also decreases.
• However, if the brake fluid level decreases
quickly, please contact your specialist dealer.
Change brake fluid
WARNING
The brake fluid may only be changed by the
specialist dealer.
Have your specialist dealer check the brake fluid
according to the maintenance table and replace it if
necessary.
LUBRICATE BRAKE LEVER
The pivot points of the brake levers for front and rear
brakes must be lubricated regularly.
Front brake lever
Rear brake lever
BOWDEN CABLES
• The operation and condition of the Bowden
cables should be checked before each ride.
The ends of the cables must be greased if
necessary.
• A damaged or difficult to move cable should be
checked or replaced by your dealer.
WARNING
• Damage to the sheathing can lead to rusting
and sluggishness.
• Replace damaged Bowden cables
immediately to avoid unsafe situations.
MAINTENANCE & SERVICING

Mission 125 / 200 19
THROTTLE GRIP AND THROTTLE CABLE
Check the throttle grip before each ride. Service the
throttle cable according to the maintenance table.
SIDE AND MAIN STAND
21
Check the side stand (1) and main stand (2) before
each ride and lubricate the surfaces where metal
meets metal regularly.
WARNING
If a stand does not fold in and out easily, please
contact your specialist dealer.
TELESCOPIC SUSPENSION FORK
The condition of the telescopic suspension fork must
be checked according to the maintenance table.
Furthermore, it should be briefly checked before each
ride and treated with care products if necessary.
WARNING
Park the vehicle securely so that it cannot fall over
during the inspection.
• Park the vehicle level and upright.
• Check the inner tubes for scratches, damage
and oil leaks.
• Pull the front brake and push the handlebar
down hard several times to check the
suspension of the fork.
WARNING
• In case of damage to the fork, please contact
your specialist dealer.
• If you treat the telescopic fork with care
products, make sure that they do not get onto
the tyres or the brake system. This can lead to
dangerous accidents.
STEERING
WARNING
A worn or loose steering bearing is dangerous. Have
the steering checked according to the maintenance
table. Furthermore, it should be subjected to a brief
check if necessary.
Place the vehicle on the main stand and unload the
front wheel. This should be done by an assistant by
pushing down on the rear of the vehicle. Hold the
fork down and try to move it back and forth. If you
see play, please contact your dealer to check the
steering.
WHEEL BEARING
The wheel bearings of the front and rear wheel must
be checked according to the maintenance table.
NOTE
If you notice play in the wheel hub or if the wheel
does not turn easily, have the wheel bearing
checked by your specialist dealer.
MAINTENANCE & SERVICING

20 Mission 125 / 200
BATTERY
The battery (1) is located under the seat. This model
is equipped with a sealed and maintenance-free
battery. There is no need to refill battery acid or
distilled water.
WARNING
• Do not remove the battery cell seal under any
circumstances! This can be dangerous and will
permanently damage the battery.
• Battery acid is toxic and dangerous! It contains
sulphuric acid and can cause dangerous
chemical burns.
• Avoid skin, eye and clothing contact and always
protect your eyes when working near the battery.
• In case of contact, render FIRST AID immediately.
• In case of skin or eye contact with battery acid,
rinse the affected areas with plenty of water.
• If battery acid is swallowed, drink large quantities
of water.
• In both cases, seek medical attention as soon
as possible.
• Batteries emit explosive hydrogen gas. Keep
naked flames, cigarettes, etc. away from the
battery and provide adequate ventilation when
charging a battery indoors.
• KEEP BATTERIES AWAY FROM CHILDREN.
Charge battery
If you do not have a suitable charger, contact your
dealer to have the exhausted battery charged. The
battery discharges more quickly if you have fitted
electrical accessories.
Store battery
• If the vehicle is not used for more than one
month, remove the battery from the vehicle.
Fully charge the battery and store it in a cool,
dry place.
• If the battery is stored for more than two
months, check the charge level at least once
a month and recharge the battery if necessary.
• Fully charge the battery before reinstalling it.
• After installation, make sure that the battery
cables are connected correctly.
WARNING
If you are not familiar with how to handle the
battery, contact a specialist dealer.
NOTE
Always keep the battery charged. Storing a depleted
battery will permanently damage the battery.
FUSES
The fuses are located under the battery cover.
Change fuse
• Turn the ignition key to and switch off all
electrical consumers.
• Remove the blown fuse and insert a new fuse
with the same ampere rating.
WARNUNG
Do not use a fuse with a higher ampere rating as this may
cause serious damage to the electrical system or fire.
• After changing the fuse, turn the ignition key to
the and switch on the electrical consumers
to check.
• If the fuse blows again, please contact your
specialist dealer and have the electrical system
checked.
MAINTENANCE & SERVICING