Malaguti Password 250 i.e. Instruction manual

FRAME AND RUNNING GEAR
WORKSHOP MANUAL

3 11/06
A
PASSWORD 250 i.e.
TABLE OF CONTENTS
1
FRAME AND RUNNING GEAR
1 - INTRODUCTION
Manual updates................................................................ 6
NOTES FOR EASY CONSULTATION ...................... 6
Configuration of the pages ............................................... 6
Modified pages ................................................................. 6
Additional pages .............................................................. 6
Symbols ............................................................................ 7
Abbreviations.................................................................... 7
Units of measurement ...................................................... 7
GENERALWORKPROCEDURES .......................... 8
Suggestions...................................................................... 8
Recommendations ........................................................... 8
OPERATING SYMBOLS ......................................... 10
2 - GETTING TO KNOW
YOUR SCOOTER
TECHNICALDATA................................................... 11
Dimensions....................................................................... 11
Capacities......................................................................... 11
Engine .............................................................................. 11
Spark plug ........................................................................ 11
Transmission .................................................................... 11
Fuel system....................................................................... 11
Ignition .............................................................................. 11
Brakes............................................................................... 11
Frame ................................................................................ 11
Suspension....................................................................... 11
Battery............................................................................... 11
Tyres ................................................................................. 11
IDENTIFICATION OF MAIN COMPONENTS
(left-handside) ....................................................... 12
IDENTIFICATION OF MAIN
COMPONENTS (right-hand side) ........................... 12
IDENTIFICATIONDATA:
FRAME N° / ENGINE N°.......................................... 13
TYRES .................................................................... 14
Inflation pressure .............................................................. 14
FUELTANK ............................................................. 15
COOLANTTANK ..................................................... 16
REAR-VIEWMIRRORS ........................................... 16
HELMETCOMPARTMENT...................................... 17
GLOVE COMPARTMENT ........................................ 18
INSTRUMENTPANEL............................................. 19
DIGITAL INSTRUMENT PANEL .............................. 20
FUNCTIONSELECTION ANDWARNING
ORALARM SIGNALS ............................................. 21
Secondary menu or submenu .......................................... 21
Main menu........................................................................ 23
Bar graph .......................................................................... 23
Alarms function ................................................................. 24
MILES OR KILOMETRES SELECTION.................. 25
HANDLEBARCONTROLS ...................................... 25
Right-hand control............................................................ 26
Left-hand control .............................................................. 26
KEYSWITCH ........................................................... 27
HANDLEBARLOCK ................................................ 27
Locking ............................................................................. 27
Unlocking.......................................................................... 27
STANDS .................................................................. 28
Centre stand ..................................................................... 28
Side stand......................................................................... 28
OWNER’STOOLKIT ................................................ 29
DIMENSIONALCHECK OF FRAME ....................... 30
3 - INSTRUCTIONS FOR USE
STARTINGTHE ENGINE ................................... 31
4 - MAINTENANCE
INTRODUCTION ...................................................... 32
Warnings .......................................................................... 32
MAINTENANCETABLE........................................... 32
TRANSMISSION OIL .............................................. 33
Level check....................................................................... 33
ENGINE OIL ............................................................ 34
Engine oil level check ...................................................... 34
Oil top-up .......................................................................... 35
FRONT/REARBRAKE FLUID ................................. 36
COOLANT ............................................................... 36
Coolant temperature indicator ......................................... 37
LUBRICANTTABLE ................................................ 37
SPARK PLUG.......................................................... 38
ADJUSTING
THEREAR SHOCK-ABSORBERS .......................... 39
ADJUSTING IDLING SPEED .................................. 39
THROTTLE PLAY ADJUSTMENT ........................... 39
ADJUSTINGTHE BRAKE LEVERS ........................ 39
CHECKINGTHE PADS AND DISCS OFTHE
FRONT/REAR BRAKES (conditionand wear) ....... 40
HEADLIGHT ............................................................ 41
Adjusting the beam........................................................... 41
Replacing the headlight bulbs ......................................... 41

4 11/06
APASSWORD 250 i.e.
FRAME AND RUNNING GEAR
TABLE OF CONTENTS
1
FRONTTURNINDICATOR....................................... 42
Changing the front turn indicator bulb ............................. 43
TAILLIGHT (with brake light) ................................. 43
Replacing the taillight bulbs............................................. 44
NUMBER PLATE LIGHT ......................................... 45
Replacing the number plate light bulb ............................. 45
FUSES .................................................................... 46
BATTERY(12V - 12AH) ........................................... 47
Installing the battery ......................................................... 47
Removing the battery ....................................................... 48
Recharging the battery ..................................................... 48
5 - DISASSEMBLY
INSTRUMENT PANELWINDSHIELD ...................... 49
UPPERHANDLEBARCOVER ................................ 49
INSTRUMENT PANEL ............................................. 50
ACCESSIBILITY...................................................... 51
AMBIENTTEMPERATURE SENSOR ..................... 52
RIGHT-HAND CONTROL ......................................... 52
LEFT-HAND CONTROL ........................................... 53
FRONTFAIRING ..................................................... 53
ACCESSIBILITY...................................................... 54
HEADLIGHTS.......................................................... 55
GRILLE ................................................................... 55
FRONTMUDGUARD ............................................... 56
SPEEDOMETER SENSOR ..................................... 57
FRONTBRAKE CALIPER ....................................... 57
CHECKINGFRONTBRAKEWEAR......................... 58
REPLACINGTHE FRONT CALIPER ....................... 58
FRONTWHEEL ....................................................... 59
FRONT BRAKE DISC .............................................. 60
LEFT AND RIGHT HALF SHIELD ........................... 61
ACCESSIBILITY...................................................... 63
HORN ...................................................................... 64
RIGHT AND LEFT
LATERAL SUB PANELS ......................................... 65
ACCESSIBILITY...................................................... 66
VOLTAGEREGULATOR .......................................... 67
“CDI”CONTROL UNIT ........................................... 67
BATTERY COMPARTMENTTUNNEL COVER ........ 68
RIGHT SIDE ACCESSIBILITY ................................ 69
LEFT SIDE ACCESSIBILITY .................................. 69
BATTERY ................................................................ 70
SUB-FAIRING .......................................................... 71
LOWER FAIRING..................................................... 72
FOOTBOARD ........................................................... 75
COOLANTEXPANSIONTANK ................................ 76
SIDE STAND ........................................................... 77
Side stand switch.............................................................. 77
CENTRESTAND ..................................................... 78
MAIN ELECTRICAL SYSTEM ................................ 79
RADIATOR............................................................... 80
FAN UNIT ................................................................ 83
RADIATOR (assembly)............................................ 83
KEYSWITCH ........................................................... 84
SEAT ....................................................................... 85
HELMETCOMPARTMENT...................................... 85
SEAT LOCK ............................................................ 85
ACCESSIBILITY...................................................... 87
THROTTLE BODYAND ASPIRATION
CONNECTOR .......................................................... 88
FUEL LEVEL SENSOR........................................... 89
FUEL PUMP ............................................................ 89
PILLIONGRAB HANDLE ........................................ 90
TAILLIGHT .............................................................. 91
ACCESSIBILITY...................................................... 91
TAILLIGHT(assembly) ........................................... 92
NUMBER PLATE LIGHT ......................................... 93
REARFAIRING ....................................................... 94
ACCESSIBILITY...................................................... 95
FUELTANK ............................................................. 96
SILENCER .............................................................. 98
LAMBDAPROBEAND DISCHARGE COLLECTOR 99
DISCHARGE COLLECTORS ................................... 99
REARSHOCK ABSORBERS .................................. 100
REARMUDGUARD.................................................. 101
REARBRAKE CALIPER ......................................... 102
CHECKINGTHE REAR
BRAKE PADS FORWEAR ...................................... 102
REPLACINGTHE REAR CALIPER ......................... 102
REARWHEEL ......................................................... 103
ASSEMBLY OF REARWHEEL ............................... 104
REARDISC ............................................................. 105
NUMBERPLATEHOLDER REAR FAIRING............ 105
FILTER BOX ............................................................ 106

5 11/06
A
PASSWORD 250 i.e.
FRAME AND RUNNING GEAR
TABLE OF CONTENTS
1
PILLION FOOTREST .............................................. 109
ENGINE ................................................................... 110
BRAKEMASTER CYLINDERS ............................... 113
HANDLEBAR ........................................................... 114
FRONTFORK .......................................................... 115
FRONTDAMPER..................................................... 116
Right ................................................................................. 116
Left .................................................................................... 116
Checking the oil level in the damper................................ 117
Changing the fork oil ........................................................ 118
BRAKECALIPERS ................................................. 119
Removing the front caliper ............................................... 119
Changing the front caliper................................................ 119
Overhaul ........................................................................... 120
Removing the rear caliper................................................ 120
Replacing the rear caliper................................................ 120
Rear caliper disassembly................................................. 120
BRAKE SYSTEM .................................................... 123
BLEEDINGTHE BRAKE SYSTEM ......................... 124
Front caliper ...................................................................... 124
Rear caliper ...................................................................... 124

6 11/06
APASSWORD 250 i.e.
FRAME AND RUNNING GEAR
TABLE OF CONTENTS
1
INTRODUCTION
•ThisWorkshop Manual describesthemain electrical/mechanicalchecks,the essential checksand theassemblyof
components supplied disassembled in order to deliver a brand new vehicle (the sequence of operations is not
binding).
•It is essential to follow the instructions with great care.Work carried out carelessly or, worse still, work that has not
been accomplished, can cause injuries and damage or, in the less serious cases, complaints.
NOTE These manuals provide the necessary information and instructions for routine maintenance and serv-
icing.
Some information has been given to us by the engine manufacturers.We therefore decline all respon-
sibility for any error, omission or misrepresentation.
MALAGUTI reserves the right to make any changes and modifications hereto it deems necessary
without prior notice.
MANUAL UPDATES
• The updates will be sent by us (in a reasonable time). Every CD-Rom you receive will supersede the one already in
yourpossession.
•The table of contents will be duly updated in the event that new pages are inserted, which render the consultation
of the manual difficult.
•IMPORTANT! TheWorkshop Manuals are to be considered as essential tools to be properly kept up-to-date so as
to maintain their validity over time.
Y
X
W
Z
A
YX
WW Z
NOTES FOR EASY CONSULTATION
CONFIGURATION OFTHE PAGES
MODIFIED PAGES
• Pages that have been modified will bear the same number as the same page of the previous edition, followed by a
letter M and, in the relative box, the new date of issue.
ADDITIONAL PAGES
• Any additional pages shall bear the last number of the section to which they belong, followed by the letter A and the
new edition date.
Chapter
Section title
Page N°
Date of issue
INTRODUCTION

7 11/06
A
PASSWORD 250 i.e.
FRAME AND RUNNING GEAR
TABLE OF CONTENTS
1
F
Cs
P
Pr
S
Sc
T
V
SYMBOLS
•Symbols are provided for quick and easy reference (see the relevant heading), identifying situations requiring
utmost attention or providing practical suggestions or simple information.
•These symbols may appear next to a text (in which case they refer solely to the text itself), next to a figure (in
which case they refer to the topic illustrated in the figure and to the relative text), or at the top of the page (in which
case they refer to all the topics dealt with in the page).
NOTE The meaning of the symbols should be duly memorised as their scope is to avoid having to repeat
basic technical concepts or safety recommendations.They are therefore to be considered as“memory
tags”. In case of any doubt as to their meaning, consult the page in which they are fully described.
ABBREVIATIONS
UNITS OF MEASUREMENT
Allthedimensions in this Manualare shown in
mm.
NOTE The letter V in the illustrations refers to fixing or adjusting screws. The number following this letter
refers to the number of the same type of screw in the unit or component described and illustrated. A
letter without a number indicates quantity 1.In case of different screws being referred to in the illustra-
tion, the letterV is followed by a number and a lower case letter. Example: (V4a).
Unless otherwise specified, units and components are reassembled by proceeding in the reverse
order of removal.
Figure
Tightening torque
Page
Paragraph
Section
Diagram
Table
Screw
INTRODUCTION

8 11/06
APASSWORD 250 i.e.
FRAME AND RUNNING GEAR
TABLE OF CONTENTS
1
GENERAL WORK PROCEDURES
• Theadvice,recommendations andwarnings givenhereafterare aimed at ensuring maximumwork safetyas well
as at considerably reducing the risk of accidents, personal injury, equipment damage and idle times.We therefore
recommend observing such advice, recommendations and warnings scrupulously.
SUGGESTIONS
• Only use top quality tools and equipment.
•Only use equipment conforming to EU Directives for lifting the vehicle.
• During all operations keep tools close at hand, ideally in accordance with a predetermined sequence of use, and
anyway never leave tools on the vehicle or in concealed or hard to reach positions.
• Always keep the work area clean and tidy.
• When tightening screws or nuts, start with the larger diameter or inner fasteners, and tighten them in a“crosswise
pattern” in successive “torquing steps”.
• Preferably use open-end wrenches and tighten by exerting “pulling force” rather than “pushing force”.
• Adjustable wrenches should only be used in case of
emergency, i.e. when a properly sized wrench is not
available. During the torquing stage the movable jaw
tends to open thus risking damaging the screw head or
achieving unreliable tightening torque values. In any
case, when using an adjustable wrench, take care to
proceed as shown in the figure.
• Except in the case of occasional services, prepare a
work sheet for the customer, on which totakeanote of
allthework performed and write memos relating to any
future checks that may be required.
RECOMMENDATIONS
•Before carrying out any work on the vehicle wait for all
the parts to cool down completely.
• Foroperationsrequiring two mechanics,makesure that
the various steps to be performed by each of them are
clearly defined and coordinated beforehand.
• Make sure that each component has been properly fit-
ted before proceeding with the next one.
• Lubricate all parts (where applicable) before reinstall-
ing them.
• Gaskets, oil seals, snap rings and cotters must be re-
newed at every refitting.
• The torque settings specified in the manuals refer to
the“final torque”,whichmustbereached progressive-
ly by steps.
• Loosen and tighten aluminium alloy parts (covers) only
after the engine has cooled down fully.
• Only use screwdrivers of suitable sizes in relation to
the screws to be loosened or tightened.
• Work in a comfortable position and ensure that the ve-
hicle is stable.
• Never use a screwdriver as a lever or chisel.
• Never use pliers to loosen or tighten screws or nuts because, in addition to not providing a sufficient clamping force,
they may also damage the screw head or nut hex.
•Never tap wrenches with a hammer (or other similar tools) to loosen or tighten screws and nuts.
•Never attempt to increase leverage by attaching tubes, etc.to wrenches.
INTRODUCTION

9 11/06
A
PASSWORD 250 i.e.
FRAME AND RUNNING GEAR
TABLE OF CONTENTS
1
A
Never use open flames for any reason.
Never leave open containers or containers not suitable for holding fuel in passageways, close to
heat sources. etc.
Never use petrol to clean the vehicle or the workshop floor. Always use low flash point solvents to
clean the vehicle components.
Never suck from or blow into the fuel pipe.
When welding,make sure that there are no flammable liquids in the vicinity. Always remove the fuel
tank, even if completely empty, and disconnect the negative cable (-) from the battery.
Never leave the engine running in closed or poorly ventilated areas.
Before any servicing, make sure that the vehicle is perfectly stable.
The front wheel should preferably be anchored to fixture (A), which is integral with the lift platform.
INDICE
INTRODUCTION

10 11/06
APASSWORD 250 i.e.
FRAME AND RUNNING GEAR
TABLE OF CONTENTS
1
OPERATING SYMBOLS
IMPORTANT!
CAUTION! - Descriptions concerning operations that are potentially hazardous for the maintenance
mechanic or repairman, other workshop personnel or extraneous persons, for the environment, for the
vehicle, and for the tools and equipment.
DISCONNECT POWER - Before performing the work described, disconnect the battery negative cable.
RISK OF FIRE - Indicates operations that may constitute a fire hazard.
EXPLOSION HAZARD - Indicates operations that may constitute a risk of explosion.
TOXIC FUMES - Indicates the risk of intoxication or inflammation of the respiratory tract.
NO! - Operations to be absolutely avoided.
SYMMETRICAL OPERATIONS - Operationsto repeaton both sidesofthe unitorcomponent in question.
ENGINEWORKSHOP MANUAL - Information that can be found in the engine workshop manual.
FITTING AND ASSEMBLY OPERATIONS
REMOVAL AND DISASSEMBLY OPERATIONS
INDICEINTRODUCTION

11 11/06
A
PASSWORD 250 i.e.
FRAME AND RUNNING GEAR
2
GETTING TO KNOW YOUR SCOOTER
TECHNICAL DATA
MALAGUTI SpA reserves the right to modify technical data at any time without prior notice.
DIMENSIONS
wheel base (A), m ................................................ 1,484
max. length (B), m ................................................ 2,170
max. width (C), m ................................................. 0,760
max. height (D), m ................................................ 1,310
kerbside weight, kg.................................................. 170
max.load with rider, pillion and luggage, kg ............ 180
CAPACITIES
engine oil, cc ........................................................ 1400*
transmission oil, cc................................................. 250*
fuel tank (reserve), l........................................9,2* (3,5*)
* Guideline value
ENGINE: single cylinder, 2 valves - 4-stroke
type .............................................MINARELLI type 5MS
n° of cylinders.............................................................. 1
bore x stroke, mm ....................................... Ø 69 x 66.8
displacement, cm3............................................... 249,78
compressionratio ...........................................10±0,4 : 1
cooling ................................................................... liquid
starting system .......................................electric starter
lubrication system .......................................... wet sump
SPARK PLUG
type .......................................................NGKDPR8EA9
TRANSMISSION
Primary:automatic speed variator withV-belt.
Final:gearbox.
Automatic centrifugal clutch
FUEL SYSTEM
Injection
Fuel:unleaded petrol.
IGNITION
MORICcontrol unit (5HW)
MORICstart-up coil (2JN)
BRAKES
Front brake:Ø 270mm disc-hydrauliccaliperwithdouble
Ø 25 mm piston.
Rear brake:Ø 240 mm disc - hydraulic caliper with Ø 30
mm piston.
FRAME
High strength steel tubing.
SUSPENSION
Front: Hydraulic fork Ø 35 mm - travel: 110 mm
Rear: Swinging engine with double dual chamber
hydraulic shock absorber - travel: 110 mm
BATTERY
Type:12V, 12Ah, sealed unit.
TYRES
Front: —— 110/70 - 16 60P (tubeless)
Rear: — 140/70 - 16 65P (tubeless)
Itispossibleto use tyres withload and speedindexesthat
are higher than or identical to those indicated.It is howev-
er necessary for speed indexes to be identical for both
tyres.
GETTINGTOKNOWYOURSCOOTER

12 11/06
APASSWORD 250 i.e.
FRAME AND RUNNING GEAR
2
GETTING TO KNOW YOUR SCOOTER
13161415
1 2 3
4
5
6 87
10
9
12
11
2425
26
27
28
29
21
22
23
20
19
18
17
IDENTIFICATION OF MAIN
COMPONENTS (left-hand side)
1) Instrument panel
2) Windshield
3) Right-hand mirror
4) Keyswitch
5) Fuses
6) Twin seat
7) Fuel tank cap
8) Pillion grab handles
9) Rear turn indicators
10) Parking and stop lights
11) Number plate light
12) Number plate holder
13) Air filter
14) Centre stand
15) Side stand
16) Left-hand pillion bracket
17) Bag hook
18) Glove compartment
19) Left-hand mirror
IDENTIFICATION OF MAIN
COMPONENTS (right-hand side)
20) Front turn indicator
21) Front parking light
22) Headlights
23) Radiator
24) Coolant tank
25) Battery
26) Right-hand pillion bracket
27) Muffler
28) Anti-theft hook
29) Helmet compartment

13 11/06
A
PASSWORD 250 i.e.
FRAME AND RUNNING GEAR
2
GETTING TO KNOW YOUR SCOOTER
B
A
IDENTIFICATION DATA:
FRAME N° / ENGINE N°
• To gainaccess tothe vehicleidentification number(VIN)
(A), lift the right-hand rubber floor mat and remove the
cover.
• Engine identification data are located on the left-hand
enginecrankcase(B).
Alteration of identification data is a criminal
offence.
• When ordering spare parts it is essential to quote the
vehicle identification data.

14 11/06
APASSWORD 250 i.e.
FRAME AND RUNNING GEAR
2
GETTING TO KNOW YOUR SCOOTER
T.W.I.
2 mm
TYRES
Type:Tubeless
NOTE It is possible to use tyres with load and speed
indexes that are higher than or identical to
those indicated. It is however necessary for
speed indexes to be identical for both tyres.
USE ONLY TYRES WITH THE RELEVANT
TYPE APPROVAL
Checkthecondition ofyourtyres (beforeeachtrip): iftheyare damaged (cracks)or cut, havethemreplaced assoonas
possible.
ThereareT.W.I.marksall aroundthetyre sidewalls.These correspondto tyrewearindicatorssituatedin thetyre’stread;
ifthere is nodifference between thethickness ofthetyre wearindicatorsand thetreaddepth, thetyremust bechanged.
NOTE Minimum tread depth (front and rear) is 2 mm.
INFLATION PRESSURE
Tyre inflation pressure must be adjusted while the tyre is at ambient temperature.
NOTE Inflation pressure differing from the specified values can lead to higher fuel consumption, irregular
tyre wear, impaired vehicle performance and riding conditions.

15 11/06
A
PASSWORD 250 i.e.
FRAME AND RUNNING GEAR
2
GETTING TO KNOW YOUR SCOOTER
A
FUEL TANK
To access the fuel tank, proceed as follows:
• Place the scooter on the centre stand.
• Opentheseat byturning theignitionkeycounter-clock-
wise.
• Unscrewcap(A) andrefuel.
• Afterrefuelling removeany tracesof fuelfrom thescoot-
er body immediately since fuel may damage surface
finishes.
• The quantity of fuel and the use of the reserve fuel ca-
pacity are displayed by the relative function of the on-
boardcomputerandtheamberwarninglightonthe right-
hand side of the instrument panel.
• Use UNLEADED PETROL.
*Guidelinevalue
Petrolisextremely inflammable;avoidapproachingthe fuelfiller-also whenrefuelling-with litcigarettes
or naked flames (e.g. matches). Fire hazard!
FUELTANK litres
TOTALTANK CAPACITY 10*
RESERVE 3,5*

16 11/06
APASSWORD 250 i.e.
FRAME AND RUNNING GEAR
2
GETTING TO KNOW YOUR SCOOTER
A
A
B
MAX
MIN
COOLANT TANK
To accessthe engine coolanttanklift up therubber mat on
the right-hand side.
Owing to the position of the tank, the level of coolant with
respecttothe“MIN”and“MAX”levelmarks,canbe checked
throughtheframenumber inspection window(A)(see rel-
ative heading).
Use the coolant type prescribed in this man-
ual or a coolant with identical characteristics
when topping up the coolant tank.
To avoid burns never remove coolant tank
cap (B) when the engine is hot.
Do not top up with water except in emergen-
cy situations, in which case drain the tank
completely and fill with the prescribed cool-
ant as soon as possible.
REAR-VIEW MIRRORS
The left and right rear-view mirrors must be fitted to the
specific locations on the handlebar and firmly secured in
place.
Adjust the visual angle of the mirrors while sitting on the
scooter in its riding conditions. Orient the mirror until you
obtain the best visibility (A).
Takecare:objects behindyouareactuallycloser thanthey
appear when seen in the rear-view mirrors.
Do not adjust the rear-view mirrors while riding. Always
wait until you are stopped (e.g. at a traffic light).

17 11/06
A
PASSWORD 250 i.e.
FRAME AND RUNNING GEAR
2
GETTING TO KNOW YOUR SCOOTER
HELMET COMPARTMENT
• The helmet compartment is under the pillion seat. To
gain access to the compartment, put the scooter on its
stand and turn the ignition key counter-clockwise to
release the seat lock.
• Thehelmetcompartmentcan accommodateaJet type
helmet, positioned as shown in the figure.
Sometypes ofhelmetmaynot fit intothe compartment.
Before choosing a helmet, make sure it fits into the
compartment.
• There is a 12V socket in the glove compartment that
canbeused,forexample,torechargea mobile phone.
The socket must only be used with the engine running
and preferably with the lights off; note that using the
socket reduces battery recharging and can reduce the
battery charge level in certain circumstances.
Do not use the socket for appliances with an excessive
power draw (max.power draw:30W).
Thesocketcan also beusedto recharge the battery by
connecting it to a battery charger for sealed batteries
when the engine is switched off.
Remembertorefit the socket cap afterusingthe socket
toprevent theingressof foreignobjects thatcould cause
short-circuits or other undesirable consequences.
The helmet compartment can be used to carry lightweight objects, which must be stowed in such a
way as to avoid negative effects on stability of the scooter while riding.
Do not insert items that are sensitive to high temperatures (lighters,inflammable liquids,perishable
goods, etc.).
Do not leave documents or valuables inside the helmet compartment.

18 11/06
APASSWORD 250 i.e.
FRAME AND RUNNING
GEAR
2
GETTING TO KNOW YOUR SCOOTER
B
A
C
GLOVE COMPARTMENT
The glove compartment is located in the central part of
the lower fairing (A) and is suitable for accommodating
small personal belongings.
It is fitted with a lock that can be opened with the ignition
key: turn the key clockwise.
The glove compartment contains the electrical system
fuses (B) and relative spare fuses (C) are contained in a
pocket in thedoor(see the relativesection inthemanual).
Do not place heavy objects or temperature
sensitive items (lighters,matches,inflamma-
ble liquids, perishable goods, etc.) in the
compartments. Do not leave documents or
valuables in the compartments.

19 11/06
A
PASSWORD 250 i.e.
FRAME AND RUNNING GEAR
GETTING TO KNOW YOUR SCOOTER
2
INSTRUMENT PANEL
1) Multifunction digital instrument panel
To set up the various functions refer to the
relative heading in the manual.
2) Analogue instruments. / Speedometer
Indicatesthe currentspeedin km/hand mph.
3) Coolant temperature indicator
The warning light comes on to indicate that
the coolant temperature is too high.
4) Red engine stop light
This light illuminates to indicate that the
“Engine Stop”button is set to OFF.
5) Green low beam indicator light
6) Blue high beam indicator light
7) Green left-hand turn indicator light
8) Green right-hand turn indicator light
9) Fuel level indicator
The warning light illuminates to indicate that
the reserve fuel level has been reached.
10) Injection warning light. Whenonor blinking
it indicates an anomaly in the injection
system.
11) This light is not used
The engine is not equipped with a pressure
probe so the oil warning light is not
connected and has checking purposes only.
Always observe the scheduled service
intervals(seeMAINTENANCETABLE) andthe
instrument panel indications when the
keyswitch is set to ON.
Do not clean the instruments with high pres-
sure washers (risk of damage).
7
45
6
1
9
8
3
2
10
11

20 11/06
APASSWORD 250 i.e.
FRAME AND RUNNING GEAR
GETTING TO KNOW YOUR SCOOTER
2
3
2
1
DIGITAL INSTRUMENT PANEL
The digital instrument panel provides data for the rider to enable optimum management of the scooter.
When the ignition key is set to , all displays on the instrument panel will illuminate for approximately 3 seconds to
check that they are working correctly; the backlighting and warning lights will illuminate simultaneously for the same
reason.
During this phase the engine displacement, speedometer unit of measurement, and scooter model will appear on the
display.
The automatic check described above is performed every time the ignition key is turned to .
When this signal disappears, the following appear:
1)Secondary Menu or Submenu
2) Main Menu
3)Bar graph
To selecta function, presstheMODE button ontheright-hand control.Operationofthe MODE buttonis illustratedin the
followingdiagramsby means of an“arrow”symbol accompanied bythetime for which thebuttonmust be helddown.If
the time is not specified, momentary pressure on the button (< 1 sec.) is sufficient.
The available functions are divided into Main Menu and Secondary Menu or Submenu .
The digital display can show warning and alarm signals that notify the rider when it is time to have the vehicle
serviced, when to changetheengine oil, whetherthereis a riskof ice on theroad,etc.;thealarm signalsare illustrated
and explained below.
MODE button not
pressed for 4”
(total) (partial) (average) (time) (exterior)
Bar Graph
selection
Reset Reset Time adjustment Main Menu
selection:
Speed
No pressing
for3”