Malloca MC 9082 ISLAND User manual

COOKER HOOD
INSTRUCTION MANUAL
MODEL: MC 9082 ISLAND

Fi g. 1
Fi g. 2 Fi g. 3
Fi g. 4 Fi g. 5
750

Fig.6 Fig.7
Fig.8 Fig.9

Fi g. 10 Fi g. 11
Fi g. 12 Fi g. 13
A B
Fi g. 14 Fi g. 15
Fi g. 16

GENERAL
Carefully read the following important information regarding installation
safety and maintenance. Keep this information booklet accessible for further
consultations.
The appliance has been designed for use in the ducting version (air exhaust
to the outside –Fig.1B), filtering version (air circulation on the inside –
Fig.1A)
SAFETY PRECAUTION
1. Take care when the cooker hood is operating simultaneously with an
open fireplace or burner that depend on the air in the environment and are
supplied by other than electrical energy, as the cooker hood removes the
air from the environment which a burner or fireplace need for combustion.
The negative pressure in the environment must not exceed 4Pa (4x10-5
bar). Provide adequate ventilation in the environment for a safe operation
of the cooker hood.Follow the local laws applicable for external air
evacuation.
Before connecting the model to the electricity network:
- control the data plate (positioned inside the appliance) to ascertain that the
voltage and power correspond to the network and the socket is suitable. If in
doubt ask a qualified electrician.

2. WARNING !
In certain circumstances electrical appliances may be a danger hazard.
A) Do not check the status of the filters while the cooker hood is operating
B) Do not touch bulbs or adjacent areas, during or straight after prolonged
use of the lighting installation.
C) Flambè cooking is prohibited underneath the cooker hood
D) Avoid free flame, as it is damaging for the filters and a fire hazard
E) Constantly check food frying to avoid that the overheated oil may
become a fire hazard
F) Disconnect the electrical plug prior to any maintenance.
G) This appliance is not intended for use by young children or infirm
persons without supervision
H) Young children should be supervised to ensure they do not play with the
appliance
I) There shall be adequate ventilation of the room when the range hood is
used at the same time as appliances burning gas or other fuels
J) There is a risk of fire if cleaning is not carried out in accordance with the
instructions
INSTALLATION INSTRUCTIONS
Assembly and electrical connections must be carried out by specialised
personnel.

The appliance has been manufactured as a class I, therefore earth cable is
necessary.
The connection to the mains is carried out as follows:
If not provided, connect a plug for the electrical load indicated on the
description label. Where a plug is provided, the cooker hood must be installed
in order that the plug is easily accessible.
An omnipolar switch with a minimum opening of 3mm between contacts, in
line with the electrical load and local standards, must be
the appliance
placed between
and the network in the case of direct connection to the
electrical network.
•The minimum distance between the support surfaces of the cooking pots on
the cooker top and the lowest part of the cooker hood must be at least 75 cm.
If a connection tube composed of two parts is used, the upper part must be
placed outside the lower part. Do not connect the cooker hood exhaust to
the same conductor used to circulate hot air or for evacuating fumes
from other appliances generated by other than an electrical source.
Before proceeding with the assembly operations, remove the anti-grease
filter(s) (Fig.12) so that the unit is easier to handle. In the case of assembly
of the appliance in the suction version prepare the hole for evacuation
of the air.
• Hood assembly
Remove the structure from the packaging and separate the upper part from
IEC227
L=live
Brown
N=neutral
Blue
E=earth
Green/Yellow
• Electric Connection

the lower part.
- Please attention that the arrow is positioned on the same side as the
appliance controls. Make 4, Ø8 holes in the ceiling and drive in 3 screws
without completely tightening them(Fig2). Pay attention not to insert the
screw into the hole marked with an X on the hole template (the screws and
expansion plugs must be suitable for the type of wall).
- Take the upper part of the structure B and insert the 3 slots onto the 3
screws that are not completely tightened. (Fig3)
Rotate slightly to fit.
Drive in the fourth screw X and tighten the remaining 3 to allow definitive
blocking of the upper part of structure B.
-Take the lower part of the telescopic structure C and insert it into the
upper structure B.
-Adjust the height (Fig.5) by referring to the amounts indicated in and
block it using the 8 unit screws G that are supplied (Fig.4)
-Suction version: fix the flexible pipe to the prepared air evacuation hole
(Fig.6).
-Take the upper chimney piece and fix it with 4 unit screws G. （Fig.7）
-Take the lower chimney and fix it with 2 unit screws G, drive in hood to
avoid it down .（Fig.8）
-Insert the suction unit inside the structure and set in 4 mounting hole,
drive in 4 unit screw N (Fig.9).
-Fix the air evacuation pipe H (not supplied) onto the connection flange
(Fig.10)
-Unscrew the 2 screws G.and rest the lower chimney piece above the
cooker hood (Fig.11).

-If the cooker hood is supplied with a lower chimney piece that must be
fixed to the hood body with screws, remove the anti-grease filters from
the hood by acting on the relevant handles (Fig.12). Then screw the lower
chimney piece pipe to the inside of the hood, using screws P(Fig.13).
Re-locate the filters in their seat.
USE AND MAINTENANCE
• It is recommended to operate the appliance prior to cooking.
It is recommended to leave the appliance in operation for 15 minutes after
cooking is terminated in order to completely eliminate cooking vapours and
odours.
The proper function of the cooker hood is conditioned by the regularity of
the maintenance operations, in particular, the active carbon filter.
• The anti-grease filters capture the grease particles suspended in the air, and
are therefore subject to clogging according to the frequency of the use of the
appliance.
In order to prevent fire hazard, it is recommendable to clean the filter at a
maximum of 2 months by carrying out the following instructions:
- Remove the filters from the cooker hood and wash them in a solution of
water and neutral liquid detergent, leaving to soak.
- Rinse thoroughly with warm water and leave to dry.
- The filters may also be washed in the dishwasher.
The aluminum panels may alter in color after several washes. This is not
cause for customer complaint nor replacement of panels.
• The active carbon filters purify the air that is replaced in the environment.
The filters are not washable nor reuseable and must be replaced at maximum

every four months. The saturation of the active carbon filter depends on the
frequency of use of the appliance, by the type of cooking and the regularity
of cleaning the antigrease filters. (Fig.14) To remove the charcoal filters
place on hand on one filter at a time and turn it toward the front part. The
charcoal filter can now be removed. Always ensure to replace both filters at
the same time.
•Clean the fan and other surfaces of the cooker hood regularly using a cloth
moistened with denatured alcoholor non abrasive liquid detergent.
•The illumination installation is designed for use during cooking and not for
prolonged general illumination of the environment. Prolonged use of the
illumination installation notably reduces the duration of the bulb. Use a
one-edged screwdriver or any other appropriate tool to lift and remove the
overhead light fixture. Replace the damaged lamp. Use only halogen lamps
as the original specification, avoiding contact with hands. Return the light
fixture to its position (snap fastening). (Fig. 15)
•COMMANDS: (Fig.16)
A= Timer (automatic shut off)
B= Speed 1 / adjust / switch off
C= digital display screen (showing timer and speed)
D= Speed 3 / adjust / switch off
E= Light
When pushing A, digital display screen shows "15 minutes" for timer, and
the minutes can be adjusted by pushing " " or " " on B and D. And the first
speed is on, pushing A once to switch off, the digital display shows "00".
When pushing B, it shows "F1" on the digital display screen, and the first
speed is on. Pushing B once to switch off, and the digital display shows "00".
When pushing D, it shows "F3" on the digital display screen, and the third
speed is on. Pushing D twice to switch off, and it shows "00" on the screen.
The second speed F2 and Turbo speed F4 can be adjusted by pushing B or D.
When pushing E, the buttons light is on and the light is on, only push E once
again to switch off the light.
If the motor, light are working together, or only motor is working, pushing A,
automatic switch off timer is on, and it will delay 15 minutes to turn off the
motor and light. To push B or D to adjust the time, and to pust A again to stop
the timer.

Troubleshooting
Problem Possible reason Solution
Hood doesn’t work No electric supply Check the plug is connected
Check the main switch is turned on
Poor airflow Aluminum grease
filters clogged
Clean the filters and replace when
dry
Charcoal filters
clogged
Replace the charcoal filters
Motor running but no
air flow
Butterfly valve jammed Contact technician
Motor cuts after a
few minutes
High t emperature
safety device activated
The kitchen is not sufficiently
ventilated
The hood is installed The hood must be least 75cm from
too near the cooking
stove
stove
Strong cooking smell
Charcoal filters not
installed
In re-circulating mode, charcoal
filters must be installed
Oil dripping onto
stove
Oil cup missing or not
installed
Remove aluminum filter and
replace oil cup
Aluminum grease filter
saturated
Wash the aluminum grease filters
Whirring sound
Something in contact
with fan blade
Contact with technician
THE MANUFACTURORY DECLINES ALL RESPONSIBILITY FOR
EVENTUAL DAMAGES CAUSED BY BREACHING THE ABOVE
WARNINGS.
Correct Disposal of this product
This marking indicates that this product should not be disposed with other
household wastes throughout the EU. To prevent possible harm to the environment
or human health from uncontrolled waste disposal, recycle it responsibly to
promote the sustainable reuse of material resources. To return your used
device, please use the return and collection systems or contact the retailer
where the product was purchased. They can take this product for environmental
safe recycling.