Manaras Opera 100 Series Installation manual

Rolling Code Transmitters - Series "100"
Rolling Code Transmitters - Series "100"
Specifications and Programming Instructions
Specifications and Programming Instructions
➢Transmitter Programming: RADIOEM101, RADIOEM102, RADIOEM103, RADIOEM104
The Opera Brand Transmitters can be used as either a 1-Door x 3-Button Transmitter or as a Multiple-Door Transmitter
Commercial Sequence or SBC). Commercial Sequence or SBC settings depend on the operator programming settings.
The Transmitters can be re-programmed as needs change. Replacement Battery: 1x CR2032 3V).
Transmitter Modes and Functions Transmitter Programming
RADIOEM101
1-Door
1-Button Transmitter (1)
1.OPEN / STOP / CLOSE → Only Button
No initial programming is required.
The Transmitters are ready to be matched to the
Receiver of your choice, refer to section Transmitter
to Operator Matching Pairing), p. 3.
RADIOEM104
4-Door
4 1-Button Transmitter (1)
1.DOOR #1 → Top Left Button
2.DOOR #2 → Top Right Button
3.DOOR #3 → Bottom Left Button
4.DOOR #4 → Bottom Right Button
(1) Each button acts separately as a 1-Button Transmitter.
Commercial Sequence or SBC Programming depends on the Operator Settings, please refer
to the Commercial Sequence or SBC Programming instructions, p. 4).
RADIOEM102
Mini Key Chain
1-Door
3-Button Transmitter
(Factory default for RADIOEM103SD)
1.OPEN → Top Button
2.CLOSE → Middle Button
3.STOP → Bottom Button
1.Press and HOLD Buttons j and l for 5 sec.
The RED LED will BLINK.
You have 15 sec. to complete the configuration or
you will need to restart.
2.Release Buttons j and l.
3.Press Button j.
4.The RED LED will stop blinking.
Programming is now complete.
RADIOEM103
Single Door (SD) /
Multiple Door
(MD)
3-Door
3 1-Button Transmitter (1)
(Factory default for RADIOEM102 &
RADIOEM103MD)
1.DOOR #1 → Top Button
2.DOOR #2 → Middle Button
3.DOOR #3 → Bottom Button
1.Press and HOLD Buttons j and l for 5 sec.
The RED LED will BLINK.
You have 15 sec. to complete the configuration or
you will need to restart.
2.Release Buttons j and l.
3.Press Button l.
4.The RED LED will stop blinking.
Programming is now complete.
(1) Each button acts separately as a 1-Button Transmitter.
Commercial Sequence or SBC Programming depends on the Operator Settings, please refer
to the Commercial Sequence or SBC Programming instructions, p. 4).
1-800-361-2260
www.manaras.com 1TN1054 REV 2 - 2022/01/24
j
k
l
m
k
l
j
j
j
k
l

Rolling Code Transmitters - Series "100"
Rolling Code Transmitters - Series "100"
Specifications and Programming Instructions
Specifications and Programming Instructions
➢Transmitter Programming: RADIOEM144
The RADIOEM144 Rolling Code Transmitter can be used to control up to 144 doors with Open / Close / Stop function.
Two rotary dials Letters: A to L) and Numbers: 1 to 12) permit for a proper door selection. The Transmitter can be re-
programmed as needs change. Replacement Battery: 2x AA 1.5V).
Transmitter Modes and Functions Transmitter Programming
RADIOEM144
Multiple Door (up to144 doors)
3-Button Transmitter
1.OPEN → Top Button
2.CLOSE → Middle Button
3.STOP → Bottom Button
No initial programming is required.
This Transmitter is ready to be matched to the
Receiver of your choice, refer to section Transmitter
to Operator Matching Pairing), p. 3.
➢Transmitter to Operator Matching (Pairing
The On-Board Radio Receiver RADIORE101, featuring Rolling Code Technology, is factory installed on all operators
equipped with an Electronic Control Board BOARD 070 since November 2013.
The Series 100 Transmitters are compatible with the RADIORE101 Receiver, as well as the on-site installation kits
RADIOKIT004/005 operators prior to November 2013) and the External Radio Receivers RADIORE901/901A/901B.
The Series 100 Transmitters are also compatible with RADIORE102, except for RADIOEM103SD and RADIOEM144.
Compatible Receivers
RADIORE101 (ECB BOAR070) /
RADIOKIT004 (RADIOKIT005)
(On-site Installation Kits)
RADIORE901/901A
(RADIORE900/900A)
RADIORE901B
(RADIORE900B)
RADIORE102
not compatible with
RADIOEM103SD and
RADIOEM144)
1-800-361-2260
www.manaras.com 2TN1054 REV 2 - 2022/01/24

Rolling Code Transmitters - Series "100"
Rolling Code Transmitters - Series "100"
Specifications and Programming Instructions
Specifications and Programming Instructions
➢Matching the Transmitter to the On-Board Radio Receiver RADIORE101 or to the
External Universal Radio Receivers RADIORE901/901A/901B
Note: For RADIORE102, consult TN1028 for pairing instructions.
To MATCH the Transmitter to the Receiver:
Once the Transmitter has been correctly programmed according to instructions
found on p. 1-2, select the Receiver of choice, refer to Figure 1 or Figure 2 and
follow the steps below:
For RADIOEM101/102/103/104:
1. HOLD the Receiver's LEARN button until the LED BLINKS for
approx. 2 sec. frequency of 1 sec. ON / 1 sec. OFF).
2. To program in 3-Button Mode: On the Transmitter, HOLD any button
until the Receiver's LED stops blinking .
3. To program in 3 1-Button Mode: On the Transmitter, HOLD the
desired button that you want programmed until the Receiver's LED
stops blinking .
For RADIOEM144:
1. Adjust the Transmitter's rotary dials to the desired positions to permit for
the proper door selection.
2. HOLD the Receiver's LEARN button until the LED BLINKS for
approx. 2 sec. frequency of 1 sec. ON / 1 sec. OFF).
3. On the Transmitter, HOLD any button until the Receiver's LED stops
blinking .
Note: You can match 1-Button, 3-Button, 4-Button AND 144-Door Transmitters
with the same Receiver. Mix and match any of the Series 100 Transmitters
accordingly for your application ordered separately). One Receiver will accept
up to 50 Transmitters.
To DELETE ALL Transmitters from the Receiver's Memory:
1. HOLD the Receiver's LEARN button until the LED BLINKS for approx. 10 sec. frequency of 1/3 sec. ON /
1/3 sec. OFF).
1-800-361-2260
www.manaras.com 3TN1054 REV 2 - 2022/01/24
Figure 1 - RADIORE101
(ECB BOARD070 /
RADIOKIT005)
Figure 2 - RADIORE901
(RADIORE901A/901B)
LED (RED)
LEARN
BUTTON
ANTENNA
LED (WHITE)
ANTENNA
LEARN
BUTTON

Rolling Code Transmitters - Series "100"
Rolling Code Transmitters - Series "100"
Specifications and Programming Instructions
Specifications and Programming Instructions
➢Commercial Sequence or SBC Programming (Optional
Modes Functions Programming (on operator's ECB)
Commercial
Sequence -
1-Button
OPEN / CLOSE → Button
Door is CLOSED:
- Click Button → Door OPENS FULLY
During UPWARD Travel:
- Click Button → Nothing happens
Door is OPENED:
- Click Button → Door CLOSES FULLY
During DOWNWARD Travel:
- Click Button → Door reverses and OPENS FULLY
Door is STOPPED:
- Not possible in this mode. Door is either FULLY
OPENED or FULLY CLOSED.
Standard default mode.
1.Door is in fully CLOSED position.
2.On ECB, verify if the close limit
switch is activated CLOSE LED is
ON).
3.On ECB, set selector switch on
9 = SBC.
4.On ECB, press “STOP” button.
5.On ECB, select run mode
(1, 4, or 5).
Single Button
Control (SBC)
Available with the
Electronic Control
Board ECB) only.
Alternating
Sequence
OPEN / STOP / CLOSE → Button
Door is CLOSED:
- Click Button → Door OPENS
During UPWARD Travel:
- Click Button → Door STOPS
Door is STOPPED:
- Click Button → Door CLOSES
During DOWNWARD Travel:
- Click Button → Door STOPS
Door is STOPPED:
- Click Button → Door OPENS
Note: If the door is STOPPED for more than 2 minutes,
the next movement will be UPWARD regardless of the
previous movement.
1.Door is in fully CLOSED position.
2.On ECB, verify if the close limit
switch is activated CLOSE LED is
ON).
3.On ECB, set selector switch on
9 = SBC.
4.On ECB, press “OPEN” button.
5.On ECB, select run mode
(1, 4, or 5).
FCC and ISED
This device complies with Part 15 of the FCC Rules and Innovation, Science and Economic Development Canada’s licence-exempt RSS s).
Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any
interference received, including interference that may cause undesired operation.
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority
to operate the equipment.
NOTE: This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules and
Industry Canada ICES standards. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1) Reorient or relocate
the receiving antenna. 2) Increase the separation between the equipment and receiver. 3) Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected. 4) Consult the dealer or an experienced radio/TV technician for help.
For further information, please consult the operator's Installation & Instruction Manual or contact our Technical
Support Department at 1-800-361-2260.
1-800-361-2260
www.manaras.com 4TN1054 REV 2 - 2022/01/24