Mangar Archimedes Installation guide

freedom through lightweight solutions
ME0057 issue 3
Mangar Inc.
3020 Legacy Dr.
Suit 100-301
Plano, TX 75023
tel: [phone]
www.mangarusa.com
Mangar International
Presteigne
Powys
LD8 2UF
Wales, UK
tel: [phone]
fax: [phone] (USA & Canada)

user instructions and warranty
archimedes
freedom
through lightweight solutions

archimedes
The Archimedes by Mangar International, is a light weight
battery powered actuator driven bathlift, designed to be
easily operated. The Archimedes will give many years of
trouble free bathing, requiring only routine cleaning and
battery recharging.
ME0057 issue 3
CONTENTS
Standard Contents Pg 3
Getting Started Pg 3
Fitting the Archimedes in the bathtub Pg 4
Hand Control Pg 4
Battery State Indicator Pg 4
Using the Archimedes Pg 5
Removing the Archimedes from the bathtub Pg 5
Battery Charging Pg 6
Cleaning Pg 6
Storage Pg 6
Maintenance Pg 7
Fault Finding Pg 7
Specications Pg7
Parts List Pg 8
Symbols used on labels and instructions Pg 9
Warranty Pg 10
Ensure that you have read and fully understand
these instructions before attempting to operate the
Archimedes.
The Archimedes should only be used as a bathing
aid, NEVER use it out of a bathtub.
Ensure that  the suction cups adhere rmly to the
bath before use.
The Archimedes is designed to go as low as possible
in the bathtub. In bathtubs with exceptionally narrow
or curved sides/bases, it may be unsuitable. Always
check that the seat section is free to lower to its
full extent and rise again freely. Be certain that it is
positioned correctly before use.
Do not allow the Archimedes to lie on its back in the
bath water.
Ensure that the transfer aps will be clear of any
obstructions, such as bath handles and soap dishes,
as the seat section is raised. NOTE:Toavoidaps
becoming caught under bathtub handles, t the
supplied Flap Guards.
OnlyrechargethebatterywiththeMangarInternational
battery charger supplied with the Archimedes.
NEVER recharge the battery in the bathroom,
outdoors or in a damp environment.
Donotuseinthepresenceofammableanaesthetic
mixtures with air, oxygen or nitrous oxide.
Do not operate the actuator when it is disconnected
from the base.
Do not use the Archimedes as a support to steady
yourself when cleaning the bathtub or when reaching
into the bathtub to retrieve items.
If the Archimedes causes electrical interference with
another piece of electrical equipment, move the
equipment further apart until the interference stops.
•
•
•
•
•
•
•
•
•
•
•
•
WARNINGS
2

archimedes
ME0057 issue 3
1
2
3
4
B
A
C
A
B
A
C
A
B
C
3
freedom through lightweight solutions
Standard Contents
1 x Archimedes Bathlift (inc.twotransferaps) (A g.1).
1 x Sealed Hand Control (B).
1 x Battery charger (C).
2 x Flap Guards (with instructions).
1 x User Instructions.
Getting Started
Unpacking - Remove the contents from the packaging
and check them to make sure that no damage has been
caused during transit. If it has, contact your supplier
immediately.
Battery - This must be put on charge before using your
Archimedesforthersttimeasfollows:
Connect the hand control to the battery charger
and plug the charger into a power supply OUTSIDE
THE BATHROOM and allow the battery to charge
overnight (see “Battery Charging”).
Seat and base sections - The Archimedes can be easily
separatedintothreesections(g.2).
Seat section (A)
Base section (B)
Actuator (C)
To separate the seat from the base section and
actuator:
Fullylowertheseatandfoldthetransfer aps onto
the seat.
Release the transit tie (Ag.3)bypullingupthe‘O’
ring and lifting the ball clear of the slot in the locating
collar on the actuator.
Press the lower part of the latch at the back of the
seat (Ag.4)andlifttheseatsufcientlytoallowthe
actuator to disengage itself from the slot (B) and the
actuator locator bracket (C). The actuator can now
be removed from the base section.
Lift the seat section clear of the base section.
Reassemble in the reverse order. Do not re-attach
the transit tie unless you are intending to carry the
assembled Archimedes.
The transit tie should only be re-attached to the back of
the seat section in order to keep both the seat and base
sections together whilst carrying the Archimedes.
•
•
•
•
•
•
•
•
•

7
5
A
B
A
A
6
4
archimedes ME0057 issue 3
Fitting the Archimedes in the bathtub
Before placing the Archimedes in a bathtub, check
that the surface where the suction cups will be
sitting is clean and free from bath oil and cleaning
residue. Remove anti-slip matting from this area.
WARNING: The suction cups may not adhere properly
on textured and non-slip areas of a bathtub.
Remove the actuator and seat section from the base
(see “Getting Started”). Moisten each of the suction
cups and place the base section as close to the
back slope of the bathtub as possible. Reposition
the actuator in the socket at the back of the base unit
(Ag.5).
Fold the transfer aps onto the seat and slide the
seat section onto the base section. Position the top
end of the actuator into the slot in the latch (B) at the
backoftheseatsectionandmakesurethatit‘clicks’
into place.
Plug the hand control into the actuator cable and
fasten the retaining clip (Ag6).
Hand Control
The hand control is a completely sealed unit containing
a rechargeable battery and battery state indicator light;
it contains no user serviceable parts. DO NOT attempt
to open.
Battery State Indicator
Wheneitherthe‘Up’or‘Down’buttonsarepressed,the
indicator light (Ag.7)showsthestateofthebatteryas
follows:
GREEN - OK to use.
FLASHING GREEN - OK to use but the battery needs to
be recharged after this bath.
RED - The battery needs recharging before use. The seat
will not lower. NOTE: The microprocessor in the
hand control will not allow the seat to be lowered
if it detects that there will not be enough battery
power to raise it again.
The battery is not replaceable. When it reaches the
end of its working life, indicated by failure to accept
or retain charge (frequently showing red on the battery
state indicator), the complete hand control will need to
be replaced with a new one. It should be returned to your
supplier for safe disposal. DO NOT dispose of the hand
control with your normal household trash. Batteries should
be disposed of in accordance with local regulations.
•
•
•
•

10
8
9
A
5
freedom through lightweight solutions
archimedes
ME0057 issue 3
Using the Archimedes
Pressthe‘Up’buttononthehandcontroltoraisethe
seat.
Release the ‘Up’ button when the seat is level with
the edge of the bathtub. NOTE: Make sure that the
transferapislevelwithandsupportedontheedge
ofthebathtub(g.8)beforetransferring.
Sitontheapandtransferacrossontotheseat.
Pressthe‘Down’buttontoloweryourself.Releasing
the button at any point will stop the seat.
To raise the seat, press the ‘Up’ button. Release
the button when the  transfer ap is level with and
supported on the edge of the bathtub.
WARNING: In an emergency, the seat movement can be
stopped at any time by disconnecting the hand control
bypullingitawayfromtheactuatorlead(g.9).
NOTE:Releasingthe‘Up’or‘Down’buttonsatanytime
will also stop the seat movement.
Removing the Archimedes from the bathtub
Fully lower the seat.
Foldthetransferapsontotheseat.
Press the latch at the back of the seat (see Ag.4)
and lift the seat clear of the base and place it on the
bathroomoor.
Lift out the actuator from the base section.
Lift the suction cup release handle at the back of the
base section (A g.10)andtiltthebaseforwardsby
pushing on the guide bars.
Continue tilting the base forwards. This will
automatically release the suction on the front suction
cups and the base section can then be lifted from
the bathtub. NOTE: DO NOT use the suction cup
release handle (A) to tilt or lift the base section.
NEVER attempt to release suction on the rear suction
cups by pulling on the guide bars.
•
•
•
•
•
•
•
•
•
•
•

Battery Charging
Disconnect the hand control from the actuator.
Connect the hand control to the battery charger
(g.11).
Plug the battery charger into a power supply outside
of the bathroom and switch on. The green light on the
charger (A) will light up to indicate that the charger is
properly connected and charging.
NOTE: The green light may dim and eventually go
out as the battery reaches full charge.
When the battery needs recharging, the hand control
should be left on charge over night. The hand control
can be left on charge continuously without damaging
the battery or charger. We recommend that the hand
control is left continuously on charge when the
Archimedes is not in use, as a matter of routine.
Cleaning
Regularly clean your Archimedes with the same non-
abrasive cleaners that you normally use on your bathtub.
It is best to separate the seat and base sections prior
to cleaning. The Archimedes can be disinfected using
a proprietary sterilizing solution or any antibacterial
cleaner.
Regularcleaningwillhelptoprolongthelifeandefciency
of your Archimedes bathlift.
Storage
The Archimedes should be stored with the seat section
fully lowered and the hand control disconnected.
During long term storage, it is recommended that at
approximately three month intervals, the battery is put on
charge overnight.
When stored for long periods, ensure that the Archimedes
is thoroughly dry and stored in a dry environment.
The transit tie (Ag.12)shouldbeattachedtotheseat
section to allow the Archimedes to be easily picked up
and moved.
•
•
•
11
12
A
A
6
archimedes ME0057 issue 3

13
Specications
Archimedes
Max.userweight:  330lbs
Totalweight:   22lbs
Seatsectiononly:  11½lbs
Basesectiononly:  6lbs
Actuator:   4½lbs
Seatheight(Min/Max):  3”to17¾”(approx)
Actuatorpowerinput:  12V:7,5A 
Environmentalprotection: IP66
Battery Charger
ACInput:  120V:1,22VA:60Hz
DCOutput:  17.4V:70mA
Internalprotection:   Thermalcut-out
Environmentalprotection:  IP50
Double insulated Class II Equipment
This product is suitable for transporting in aircraft.
Hand Control
Batterytype:   NiCad
Output:   12V:7,5A
Internalprotection:  Selfresettingfuse
Environmentalprotection: IP67
Maintenance
Other than routine cleaning, the Archimedes has been designed to be maintenance free, however, we recommend that
yourArchimedesisinspectedannuallybyeitheryoursupplierorothersuitablyqualiedperson.Pleasecontactyour
supplier for further advice.
There are no user-serviceable parts in the Archimedes. Repairs or servicing must only be carried out by your supplier
or other authorized person.
Fault Finding
If the seat fails to rise:
Check that the hand control plug is FULLY pushed
intotheactuatorcablesocket(g.13).
If the seat fails to lower:
Check to see if the battery state indicator light is
showing RED. If it is, put the hand control on charge
overnight.
Check that the hand control plug is FULLY pushed
intotheactuatorcablesocket(g.13).
•
•
•
Seat Height
17¾” (Max)
3” (Min)
24”
17½”
6¾”
26¼”
7
freedom through lightweight solutions
archimedes
ME0057 issue 3
11½”
15½”
28½”

1Seat Assembly LA0010 7Actuator Latch LA0016
2Flap LA0011 8Transit Tie LA0017
3Hinge (Set of 2) LA0012 9Hand Control LA0018
4Base Assembly LA0013 10 Battery Charger LA0019
5Suction Cup (Set of 4) LA0014 11 Flap Guards (pair - with instructions) LA0021
6Actuator Assembly LA0015 12 Instruction Booklet ME0057
Parts List
1
2
2
3
5
4
6
7
8
9
12
11
5
8
archimedes ME0057 issue 3
10

IP 66
IP 67
IP 50
Attention
Consult instructions
Alternating Current
Direct Current
Class II Double Insulated Equipment
Do not connect to mains power in a
bathroom or outdoors
Dangerous Voltage Duty cycle
I = Operating time
0 = Non operating time
Sealed against the effects of immersion in
water to a depth of 1 metre
Press to raise seat
Press to lower seat
Sealed against the effects of showers
No protection against water ingress
Type B equipment (Protection against
electric shock)
Battery State Indicator
Maximum user weight limit
Date of manufacture
Recycle do not dispose of in household
trash
Symbols used on labels and instructions
Max/Min Operating Environmental
Temperature
+120º
ºF
+40º
Ni-Cd
9
freedom through lightweight solutions
archimedes
ME0057 issue 3
Symbols used on packaging
Keep packaging dry
Handle with care
Max/Min storage temperature
Do not use blade to open
Net & Gross weights
Recycle packaging
Max/Min humidity when transporting in
pressurized aircraft hold
Max/Min pressure when transporting in
pressurized aircraft hold
Max/Min temperature when transporting
in pressurized aircraft hold

10
archimedes ME0057 issue 3
Warranty
Mangar International guarantees this product for a period of two years.
The guarantee is given against defects in material and workmanship and comprises piece,
parts and labor. The guarantee is not valid in the case of fair wear and tear, wilful damage,
commonneglect,misuseorunauthorizedalterationorrepairbyunqualiedpersons.
Thefollowingstatementsdonotaffecttheconsumer’sstatutoryrights.Thisproductissoldontheunderstandingthatin
the event of any defect of manufacture or material appearing within two years of the date of receipt of this product, the
defectwillberectiedfreeofchargeprovidingthat:
(a) Reasonable evidence is provided (e.g. purchase invoice, delivery note) that the product was not purchased more
than two years prior to the date of the claim.
(b) The defect is not attributable to accidental damage (either in transit or otherwise), misuse or unauthorized
repair.
Archimedesserialnumber: .............................
Dateofpurchase: .............................
Invoice/Deliverynotenumber: .............................
MangarInternationalreservestherighttoalterproductspecicationsand/oranyoftheinformationcontainedwithinthisdocumentwithoutnotice.

11
freedom through lightweight solutions
archimedes
ME0057 issue 3