Manhattan Comfort GRANVILLE DR-500 User manual

DR-500
REV. 01
 71 0 1 2 5 8 0 0 4 6

SUPPORT SITE
QR CODE
Stuck? Question? We are here to help.
tel: [phone]
e-mail: [email protected]
View our assembly video online:
WWW.MANHATTANCOMFORT.COM
TOOLS REQUIRED
•Do not throw away packaging materials until assembly is complete.
•Assemble item on a soft surface, such as cardboard or carpet, to protect finish.
•Proper assembly requires two people.
FOR BEST RESULTS:
Before beginning the assembly process,
ensure all boxes and parts have been delivered.
STOP!
STOP!

Included in this package:
03
01
02 03
04
06
05
07
08 09
10
11
13
16
14
13
15
01.
02.
03.
04.
05.
06.
07.
08.
09.
10.
11.
12.
13.
14.
15.
16.
Top Panel
Back Panel
Right Side Panel
Left Side Panel
Bottom Panel
Foot
Feet Crossbar
Top Drawer Front
Drawer Front
Drawer Back
Drawer Right Side
Drawer Left Side
Drawer Bottom
Top Drawer Support
Top Drawer Larger Division
Top Drawer Smaller Division
x1
x1
x1
x1
x1
x2
x1
x1
x4
x5
x5
x5
x5
x5
x1
x2
06
10 11
12
12
16
33Lb
7Lb
7Lb

A x 32
#23857
B x 5
#PX.017
C x 2
#CA.002
D x 1
#2196
E x 20
#69
F x 26
#10385
G x 5
#292
H x 6
#11170
I x 4
#284
J x 10
#259
K x 26
#10386
L x 28
#1616
M x 26
#393
TIPOVER
RESTRAINT KIT
N x 1
#KT.002
O x 10
#PA.006
Included in this package:
04

01
02
Fix the hardware C to part 07 with screw L.
Then, attach the parts 06-08 with the hardware A.
A
A
A
A
C
L
L
Fix the part 07 to part 06 with screw L.
L
L
LC
L
L
L
07
06
05
07
06
06
06
A x 4 C x 2 L x 4
L x 4

03
04
Fix the part 05 to parts 06-07 with screw G and tool D.
Attach the parts 03-45 to part 05 with hardware A.
Then, fix them with screw H.
Pay attention in detail to ensure correct assembling.
Rear Side
H
A
A
A
Rear Side
Rear Side
H
H
H
H
H
A
07
06
05
04
06
G
D
03
06
05
D
G
G
G
G
G x 5
A x 4 H x 6

05
06
Fix the hardware F to part 01.
Attach the part 01 to parts 03-04 with hardware A.
Then, apply the hardware K and lock it according the example below.
Pay attention in detail to ensure correct assembling.
Rear Side
A
Rear Side
A
A
K
K
K
K
K
Rear Side
K
K
A
07
04
01
03
F
F
01
F x 6
F
F
F
F
F
K x 6
A x 4

07
08
Position correctly the part 02 and fix it with the hardware M.
Fix hardware F to parts 08 and 09.
Rear Side
F
x4
F
F
F
F
F
F
F
F
08
M
08
04
02
M
M
M
M
M
M
MM
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
09
M
M
Pay attention in detail to
ensure correct assembling.
F x 20
M x 26

09
10
Specially to part 08, fix the part 14 with screw I.
Please, start by fixing the ends. Then fix the intermediate screws.
Attach the parts 08 to parts 11-12 with hardware A.
Then, apply the hardware K and lock it according the example below.
Equaly, the same process is apllied to parts 09-11-12.
09
09
x4
K
K
KK
K
K
K
A
A
A
A
K
K
11
12
I
I
I
I
12
11
A
A
A
A
08 14
08
TOP DRAWER
K x 20
I x 4
A x 20

11
12
Apply the part 13 in the groove of the parts 11-12.
Attach the part 10 to parts 11-12-13.
Then, fix the parts 11-12 to part 10 with screw E.
10
x4
09 12
12
13
12
09
x4
10
12
E
E
E
E
E
E
TOP DRAWER
TOP DRAWER
13
11 11
08
10
11
11
13
13
09
E
E
E x 20

13
14
Apply the hardware B to parts 08-09.
Then, fix them with screw J.
Attach part 15 to parts 16.
11
x4
09
Rear Side
Rear Side
B
B
J
J
J
J
TOP DRAWER
08
15
16
16
B x 5
J x 10

15
16
Attach Assembled Divison from the last step into the Top Drawer identified by part 08.
Before to fix the Drawers, you must extract the full extension of the Slides, by pulling off.
Then, pay attention to the correctly holes according to the next steps.
12
Front Side
Front Side
08

17
18
The Drawers have pre-set holes to help you on fixing them.
Set the Drawer on correct position and pre-set holes, carefully.
Firstly, make sure that the Drawer is correctly positioned according to the detail
The correct holes of the Slides must match with the pre-set holes of the Drawers.
Position and fix them with the screw L.
Drawer pre-set holes
13
L
L
L
L
08
08
ATTENTION: extremely necessary
a second person helping.
ATTENTION: extremely necessary
a second person helping.
L x 4

19
20
You must put a drawer opening limiter screw.
Firstly, keep the drawer partially open so that the limiter screw hole is behind the
limiter bracket according to the detail.
ATTENTION: ensure the limiter screw hole is before the limiter bracket.
Then, place the screw #PA.006 to retain the full opening of the drawer.
14
08
Limiter bracket
Limiter screw hole
Limiter screw hole
Limiter bracket
Limiter bracket
O
O
O x 2

21
22
Apply the same fixing Drawers process and drawer opening limiter to the others drawers.
You must install the Tipover Restraint Kit (N) provided, in the rear side of the furniture.
Position the hardwares #18256EXP and #20522.
Fix them with screw #11179.
15
08
09
09
09
09
#2610 x 1
#16973 x 1
#11179 x 1
#20522 x 2
#18256EXP x 1
TIPOVER
RESTRAINT KIT
Rear Side
#11179
#20522
#18256EXP
O x 8 L x 16

23
24
Approach the furniture as close as possible to the wall.
Then, mark with a pencil where you should drill the wall to put in the hardware.
Put in the hardware #16973 to the hole that you drilled on the wall.
Then, position the hardwares #18256EXP and #20522.
Finally, fix them with screw #2610.
16
Use a Ø8mm drill bit to drill the wall.
Wall
#18256EXP
#20522
#2610
#16973
#16973
#20522
#18256EXP
#2610

319 Ridge Rd. Dayton, NJ 08810
908-888-0818
All Manhattan Comfort furniture products are warranted, to the original purchaser at the
time of purchase and for a period of 30 days thereafter.
Our warranty is limited to new products purchased in factory sealed cartons. This war-
ranty is valid in the United States of America and Canada.
In order to provide you with timely assistance, please thoroughly inspect your furniture
for missing or defective parts immediately after opening the carton.
Manhattan Comfort offers a 30-day parts replacement warranty on all items.
Our furniture products are not intended for outdoor use.
THE WARRANTY DOES NOT COVER:
- Defects/damages by improper assembly or disassembly.
- Defects/damages caused by shipping. Claims for damage during transit should be
placed immediately to the transportation company.
- Defects/damages caused by inappropriate use of the furniture.
WARRANTY POLICY