Maple Systems Graphic HMIs Manual

.Maple Systems Inc., 808 134th Street SW, Suite 120, Everett, WA 98204-7333 –www.maplesystems.com
1036-0203 Page 1 of 4 Rev. 01, 10/11/2015
CONTROLLER INFORMATION SHEET
Maple Model(s) PLC or Controller
Graphic HMIs Siemens S7-200 SMART (PPI)
P/N: 1036-0203
Rev. 01 Date: 10/11/2015
Summary
Maple Systems Graphic HMIs communicate with Siemens S7-200 SMART modules via PPI.
When configured with EZware, the Graphic HMI is the master in a point-to-point single
master, single slave format. Please refer to the Installation and Operations Manual for
information on connecting multiple Graphic HMIs to a single PLC port.
Communications Cab le
The Graphic HMI should be connected to the controller’s PPI port. A list of communications
cables offered by Maple Systems as well as cable assembly instructions to assist you in
assembling your own communications cable are available on our website at
www.maplesystems.com.
WARNING If your communications cable is not wired exactly as shown in our cable
assembly instructions, damage to the HMI or loss of communications can
result.
PLC Controller Settings
The PLC station number cannot be the same as the HMI station number.

Phone: [phone] • Fax: [phone] • Email: suppo[email protected]m • www.maplesystems.com
1036-0203 Page 2 of 4 Rev. 01, 10/11/2015
Accessible PLC Mem ory
Register M emory
The following table lists the PLC’s register memory ranges that the Graphic HMIs are able to
access. Please note that your PLC’s memory range may be smaller or larger than that
supported by these HMIs. The following register memory can be displayed in 16-bit or 32-bit
format on the Maple HMI. (Note: d=decimal )
PLCRegister Type
AddressRange
Format
PLCRegister Description
MW
0-30
dd
Word Memory
VW
0-20478
ddddd
V Memory
SMW
0-1534
dddd
Special Memory
T
0-255
ddd
Timer
C
0-255
ddd
Counter
AIW
0-110
ddd
Analog Input
AQW
0-110
ddd
Analog Output
VD
0-20476
ddddd
V Memory (Double Word)
Discrete Memo ry
The following table lists the PLC’s discrete memory ranges that the Graphic HMIs are able to
access. Please note that your PLC’s memory range may be smaller or larger than that
supported by these HMIs. The following discrete memory is displayable in single-bit format
on the Maple HMI.
(Note: d=decimal, o=octal)
PLCBit Type
AddressRange
Format
PLCBit Description
I
00-317
ddo
Input Bit (Read Only)
Q
00-317
ddddo
Output Bit
M
00-317
dddddo
Bit Memory
V
00-204797
dddddo
V Memory Bit
S
00-317
ddo
SCR
SM
00-15357
ddddo
Special Memory Bit
Timer
0-255
ddd
Timer
Counter
0-255
ddd
Counter

.Maple Systems Inc., 808 134th Street SW, Suite 120, Everett, WA 98204-7333
1036-0203 Page 3 of 4 Rev. 01, 10/11/2015
EZwareSettings
The following table lists the communications settings that must be configured in
EZware. These settings can be found in the Edit-System Parameters menu under the
Device Properties tab. Please note:
The Recommended Settings column provides the recommended setting
based upon the default settings most commonly used in Siemens modules.
The Options column lists EZware’s options; your PLC may not support
every option
Name
Recommended
Settings
Options
ImportantNotes
Name:
Siemens S7-200
Smart (PPI)
Descriptionlabel
HMIor PLC
PLC
Location
Local
Local,Remote
SelectLocal if PLC directly
connected to HMI, Remote
if PLC connected thru
another HMI.
PLCtype:
Siemens S7-200
Smart (PPI)
PLC I/F:
RS485 2W
RS-232,
RS-485 2W,
RS-485 4W
Mustmatch the controller port
setting.
PLCdefault station
no.:
2
1-126
Must match the node address
assigned to the PLC.
Setting: COM:
COM1
COM1-COM3
Serial port of the HMI connected
to the controller.
Settings: Baud rate
9600
9600, 19200,
187.5K
Mustmatch the PPI port
setting. Use the fastest
baud rate supported by the
controller.
Settings:Data Bits
8
7 or 8
Must match the PPI port setting.
Settings: Stop Bits
1
1 or 2
Must match the PPI port setting.
Settings: Parity:
Even
Even, Odd,
None
Must match the PPI port setting.

Phone: [phone] • Fax: [phone] • Email: suppo[email protected]m • www.maplesystems.com
1036-0203 Page 4 of 4 Rev. 01, 10/11/2015
Name
Recommended
Settings
Options
ImportantNotes
Settings:Timeout
(sec)
1.0
0.1to 25.5
Adjustif longer timeout is
required.
Settings:Turn around
delay (ms):
5
0-1000
Timeout period between HMI
polls.
Settings: Send Ack
Delay :
30
Settings: Reserved 1:
0
NotApplicable
Settings: Reserved 2:
0
NotApplicable
Settings: Reserved 3:
0
Not Applicable
Interval of block pack
(words):
5
0-512
Max. read-command
size (words):
16
Not Adjustable
Max. write-command
size (words):
2
Not Adjustable