Marantz SC-7S2 User manual

Stereo Control
Amplifier
SC-7S2
SC-7S2 Premium stereo control amplifier
We’ll never forget the impact the introduction of the Marantz Model 7 and Model 9 had in the
industry more than 40 years ago. These models fused original circuit design with rational thinking and
aesthetic appeal. Not only did these models help establish the Marantz name and brand in the audio
world, but also influenced the direction that audio evolution has taken ever since.That the Model 7
and Model 9 are still sought–after-components is a testament to the fact that even though musical
sources may have changed, thoughtful design and engineering continue to endure defying the laws of
music and audio history. Reviving these two numbers will enrich audio history again.The distinctive
voice of the Model 7 has been reborn in the stereo pre-amplifier SC-7S1. Now it is time for the Series 2
version to update with the latest experiences Marantz engineers made and the use of new material and
components to further excel the indescribable performance of this stereo control amplifier.

Features Benefits
State of the Art stereo control amplifier
Fully balanced control amp
Current feedback technology
Current Feedback HDAMs
Customized components
Super Ring power transformer
Choke input power supply
Rigid Multi layer copper chassis
High quality 8-gang linear volume control
Floating control bus
Built without compromises for the ultimate sound quality
in stereo or multi-channel
Superb audiophile channel separation
Excellent frequency response and superb sonic
performance
Achieving a more dynamic, accurate and detailed sound
reproduction regardless the amount of channels
For superb sound quality
Ultra low vibration and leakage flux keep the signal sharp
and minimizes internal electro magnetic distortion
Reduced rectifier harmonic noise
Eliminates all electromagnetic radiation interference and
mechanical vibration
Extreme wide bandwidth with minimized gang errors
Audiophile multi channel upgradeability
Technological glossary:
Audiophiles be prepared: the new SC-7S2 has been
completely reworked, revoiced and revamped with new
environmental-friendlier materials – and it still sustains a
spectacular channel separation of over 100dB at 20kHz. It also
now has four, instead of two, Wolfson electronic volume
controls. Combined with an extended high frequency
response of up to 150kHz, this advanced, high-quality pre-
amplifier for stereo and multi-channel set-ups provides a
super-wide range and high dynamic signal handling.
Extended high frequency response as well as channel
separation express the true meaning of “Super Audio”.
Unparalleled attention to detail in the design and
development of the input and output circuitries, volume
control section, power supply circuits, makes the SC-7S2 the
ultimate, top-rated performer in its class. And of course it is as
solid as the SA-7S1.
Audiophile perfection
The concept for the SC-7S2 was to get a pre amplifier for a
stereo and a multi channel set up with a super wide range and
a high dynamic signal handling. We think it’s of the utmost
importance to extend high frequency response as well as
channel separation so you can feel and hear the true meaning
of "Super Audio." This is why we have designed the input and
output circuitries, volume control section, and power supply
circuits according to this philosophy. The result, an
astonishing channel separation of over 100dB at 20kHz. To
understand our philosophy best, just experience this exquisite
piece of equipment
The concept
The SC-7S2 is a full balance, two-channel control amp
providing the channel separation you need for Super Audio.
Based on our own high quality four-gang active volume
control we have developed an even better eight-gang linear
control volume that reduces gang errors from 0 to 100dB, ±
0.5dB. For precise linear volume control, we used two
Wolfson WM8816’s. By adding an additional HDAM SA
(Hyper Dynamic Amplifier Module), we improved the
Common Mode Reject Ratio (CMRR) dramatically, attaining an
incredible ultra-wide frequency band of 150kHz, and
succeeded in producing the perfect control amplifier for
Super Audio CD.
Superb volume control
The Marantz HDAM-SA is a low level signal amplifier. It is in
use where the audio signal has a very low voltage level and
has to be handled with a maximum of care. Most of the other
audio brand companies are using for this integrated circuit
(IC) operational amplifier (op-amps). These ICs of course are
less expensive but unfortunately these ICs do not match the
very high requirements of Marantz. Marantz developed its
own discrete circuit boards. These HDAMs consists of
discrete components with short mirror image L/R signal paths.
These devices are doing the same thing as the Op-amps, but
outperform the regular integrated circuit Op-amps
dramatically in terms of the Slew Rate and noise level,
resulting in a much more dynamic, accurate and detailed
sound.
Marantz’ HDAM SA

The feedback impedance of the Current Feedback circuit was
reduced to its minimum to make it faster. We developed a
new Hyper Dynamic Amplifier Modules (HDAM), a
separated module operating as a buffer for the amplifier. The
SC-7S2 has four HDAMs on each input-output buffer and
another four units on the voltage/current converter.
In the power supply section, the choke input topology was
adopted to drastically reduce rectifier harmonic noise. This
system is especially suitable for a control amplifier in which
very small signal will amplified.
Choke input system
We make it possible to synchronously drive two or more
control amps by using a floating control bus system connected
to as many as 6 sets of control amplifiers. We also enable you
to trim levels using the remote control making it easy to set up
the optimal sound field on a multi-channel configuration. The
highest achievable stereo performance can be accomplished
with a system configuration of two sets of SC-7S2, and four
sets of MA-9S1 connected in a bi-amping mode. You will
experience superb sound with unbelievable channel
separation.
Floating control bus
To achieve the best possible sonic performance, signal paths
need to be short, direct and mirror imaged. The construction
of the circuitry in the SC-7S2 is fully balanced from input to
output and provides superb stereo image by ensuring
symmetry between right and left channel layout.
Perfect symmetry
The power supply of any amplifier is like the heart of the
product. Therefore we utilize in the SC-7S2 a custom made
Super Ring power transformer. These transformers have a
higher efficiency then ordinary laminate designed
transformers coupled with the advantage of extremely low
electromagnetic radiation. To prevent any radiation
interference we have encapsulated the transformer. Therefore
noise and hum into surrounding circuitry is reduced to the
absolute minimum. The sonic result speaks for itself.
Super Ring transformer
The SC-7S2 has a solid copper chassis for minimal
disturbance from electro-magnetic radiation. The multi layer
construction ensures enough critical mass to eliminate any
interference from mechanical vibrations which could damage
the integrity of the audio signal.
Solid radiation free construction

Bypacked accessoiries
- User manual
-Power cable
- Remote control
- Batteries
-F.C.B.S. link cable
RC001PM


FEATURES
Channels 2
Current Feedback Topology •
Linear Drive Power Supply •
CCNE •
Liniear volume control •
Floating control bus system •
BTL Possibility -
BI-AMP and Multichannel option •
Power Transformer: Super-ring /
Toroidal / El •/-/-
Choke input •
Shottky diodes •
HDAM: Standard / SA / SA2 /
Current Feedback -/•/-/-
HDAM cover: Gold plated /
Copper plated / Metal / plastic / no
shield
-/-/-/•/-
High Grade Audio Components •
Customised Components •
Current Feedback phono equalizer -
Input buffer amp (all inputs / CD only) •/-
Construction: Twin mono / 3-Stage
circuit -/-
Symmetric PCB Layout •
Separate Solid Heat Sinks -
System block shielding: Copper /
metal / none •/-/-
Chassis : Die-cast / Copper plated /
Metal -/•/-
Double Layer Bottom Plate •
Low noise LCD display -
Temperature Gauge -
Balance / Bass / Treble / Loudness -/-/-/-
Source Direct -
Speaker A/B -
Record Selector: full / copy-source -/-
Standby Mode -
INPUTS/OUTPUTS
Audio Inputs 4
Phono Input: MM/MC -/-
Audio Outputs 2
Balanced In/Out •/•
Processor In/Out -
Pre-out / Main-in •/-
D-Bus In/Out -
Gold Plated Cinch •
Speaker Terminal: Click-fit / Screw /
WBT -/-/-
Floating control bus (3.5mm mono jack x
2) •
AC Outlets (Not for UK Model) -
Headphone Out -
I-Pod input (direct / docking station) -/-
SPECIFICATIONS
Power Output (8/4 Ohm RMS) -/- Watts
Power Output (8/4 Ohm DIN)
Power Output (8/4 Ohm IHF)
Frequency Response 3Hz-150kHz +/-3dB
Total Harmonic Distortion 0.0015%
Bridged Power Output (8 Ohm RMS) -
Damping Factor -
Input Sensitivity: MM -
Input Sensitivity: MC -
Signal to Noise Ratio: MM/MC -/-
Input Sensitivity: High
level
420mV /
20kOhm
Signal to Noise Ratio: High level 105dB
GENERAL
Available colors: Platinum / Gold /
Silver / Black -/•/-/-
Metal Front Panel •
Power Consumption 20 Watts
Detachable Power Cable •
Remote Control RC001PM
System Remote Function -
Maximum Dimensions (W
x D x H)
459 x 441 x
136 mm
Weight 21Kg
Design and specifications are subject
to change by Marantz without notice.
www.marantz.com