Marantz SR6010 User manual

AV SURROUND RECEIVER
SR6010 /U1B/N1B/N1SG
SR6010
S0172V04DM/DG1801
Copyright 2015-2018 D&M Holdings Inc. All rights reserved.
WARNING: Violators will be prosecuted to the maximum extent possible.
Ver. 4
•Some illustrations using in this service manual are slightly different from the actual set.
•Please use this service manual with referring to the operating instructions without fail.
•For purposes of improvement, specications and design are subject to change without notice.
Please refer to the
MODIFICATION NOTICE.
Service
Manual

Contents
ABOUT THIS MANUAL................................................................3
What you can do with this manual ...........................................3
Using Adobe Reader (Windows version)...................................4
SAFETY PRECAUTIONS...............................................................6
NOTE FOR SCHEMATIC DIAGRAM..............................................7
NOTE FOR PARTS LIST................................................................7
Instructions for handling semi-conductors and optical unit ...7
1. Ground for Human Body......................................................7
2. Ground for Workbench ........................................................7
TECHNICAL SPECIFICATIONS.....................................................9
DIMENSION ..............................................................................10
CAUTION IN SERVICING ...........................................................11
Initializing This Unit.................................................................11
JIG FOR SERVICING ..................................................................11
DISASSEMBLY ..........................................................................12
1. FRONT PANEL ASSY............................................................14
2. RADIATOR ASSY .................................................................14
3. DIGITAL PCB .......................................................................15
4. VIDEO PCB..........................................................................16
5. INPUT HDAM PCB...............................................................16
6. SPK PCB..............................................................................17
7. SMPS PCB ...........................................................................17
8. TRANS POWER....................................................................17
SPECIAL MODE.........................................................................18
Special mode setting button ..................................................18
1. Version Display Mode ........................................................19
2. Selecting the Mode for Service-related Operations...........23
PROTECTION DIAGRAM.....................................................24
2-1. DIAGNOSTIC MODE (Service Path Check Mode) ..............25
DIAGNOSTIC PATH DIAGRAM ............................................29
2-2. Protection History Display Mode......................................66
2-3. 232C Standby Clear Mode................................................67
2-4. Operation Info Mode........................................................68
2-5. TUNER STEP mode (E2 / E3 only)......................................69
3. PANEL / REMOTE LOCK Selection Mode ............................70
4. Protection Pass Mode ........................................................71
5. CY920 Reboot Mode ..........................................................71
6. CY920 Initialization Mode ..................................................72
JIG FOR SERVICING ..................................................................73
Procedure after Replacing the Printed circuit boards............76
Procedure after Replacing the Microprocessor, etc...............76
FIRMWARE UPDATE PROCEDURE............................................77
1. Updating via USB ...............................................................77
2. Updating via DPMS ............................................................86
ADJUSTMENT...........................................................................93
SURROUND MODES AND PARAMETERS..................................94
TROUBLE SHOOTING................................................................97
1. POWER ...............................................................................97
2. Analog video......................................................................98
3. HDMI/DVI .........................................................................102
4. AUDIO ..............................................................................104
5. Network/Bluetooth/USB ..................................................107
6. SMPS ................................................................................112
Audio Check PASS .................................................................114
CLOCK FLOW & WAVE FORM IN DIGITAL BLOCK...................115
LEVEL DIAGRAM.....................................................................116
BLOCK DIAGRAM ...................................................................122
POWER DIAGRAM ..................................................................126
WIRING DIAGRAM..................................................................127
PRINTED CIRCUIT BOARDS ....................................................128
SCHEMATIC DIAGRAMS (01/38).............................................135
SCH01_DIGITAL CONNECT....................................................135
SCH02_DIGITAL POWER........................................................136
SCH03_MAIN CPU.................................................................137
SCH04_EXPANDER................................................................138
SCH05_CPU LEVEL CHG ........................................................139
SCH06_DIR ............................................................................140
SCH07_AUDIO PLD ...............................................................141
SCH08_DSP1 .........................................................................142
SCH09_DSP2 .........................................................................143
SCH10_DSP3 .........................................................................144
SCH11_DSP4 .........................................................................145
SCH12_ADC ..........................................................................146
SCH13_ZONE DAC ................................................................147
SCH14_CY920 .......................................................................148
SCH15_VIDEO DECODER.......................................................149
SCH16_HDMI SW2 ................................................................150
SCH17_HDMI SW1 ................................................................151
SCH18_VSP & IP & OSD .........................................................152
SCH19_VIDEO PLD ................................................................153
SCH20_HDMI TX & SCALER ...................................................154
SCH21_INPUT........................................................................155
SCH22_PREOUT.....................................................................156
SCH23_HDAM CNT & F-HDMI ...............................................157
SCH24_A-VIDEO....................................................................158
SCH25_RC-5 ..........................................................................159
SCH26_RS232C & TRIGGER....................................................160
SCH27_SIDE CNT...................................................................161
SCH28_FRONT CNT ...............................................................162
SCH29_MAIN DAC1...............................................................163
SCH30_MAIN DAC2...............................................................164
SCH31_SPK............................................................................165
SCH32_REGULATOR & TUNER...............................................166
SCH33_7CH AMP 1................................................................167
SCH34_7CH AMP 2................................................................168
SCH35_FRONT.......................................................................169
SCH36_HDAM 1 ....................................................................170
SCH37_HDAM 2 ....................................................................171
SCH38_SMPS.........................................................................172
EXPLODED VIEW ....................................................................173
PACKING VIEW .......................................................................174
SEMICONDUCTORS ................................................................175
1. IC's....................................................................................175
2. FL DISPLAY.......................................................................195
2

Jump to the target of a schematic diagram
connector
Click the Ref. No. of the target connector in the red
box around a schematic diagram connector.
•The screen jumps to the target connector.
• Page magnication stays the same as before the
jump.
CP401
CP106
v
ABOUT THIS MANUAL
Read the following information before using the service manual.
What you can do with this manual
Search for a Ref. No. (phrase)
(Ctrl+Shift+F)
You can use the search function in Acrobat Reader to
search for a Ref. No. in schematic diagrams, printed
wiring circuit diagrams, block diagrams, and parts
lists.
1. Press Ctrl+Shift+F on the keyboard.
• The Search window appears.
2. Enter the Ref. No. you want to search for in the
Search window, and then click the Search button.
• A list of search results appears.
3. Click an item on the list.
• The screen jumps to the page for that item, and the
search phrase is displayed.
Ctrl
Shift
F
3

Using Adobe Reader (Windows version)
• Properties
Click this button and check that the printer is set to a
suitable paper size.
• Page to print
Select the following checkbox.
"More Options" : "Current View"
• Page Sizing & Handling
Select the following checkbox.
"Size" / "Size Options" : "Fit"
Add notes to this data (Sign)
The Sign function lets you add notes to the data in
this manual.
Save the le once you have nished adding notes.
[Example using Adobe Reader X]
On the "View" menu, click "Sign".
• The Sign pane appears.
[Example using Adobe Reader 9]
On the "Document" menu, click "Sign".
Magnify schematic / printed circuit board
diagrams - 1
(Ctrl+Space, mouse operation)
Press Ctrl+Space on the keyboard and drag the
mouse to select the area you want to view.
• The selected area is magnied.
• When you want to move the area shown, hold
down Space and drag the mouse.
• When you want to show a full page view, press
Ctrl+0 on the keyboard.
Ctrl Space
0
Print a magnied part of the manual
The Properties dialog box and functions will vary depending on your printer.
1. Drag the mouse to magnify the part you want to print.
2. On the "File" menu, click "Print".
3. Congure the following settings in the Print dialog box.
4. Click the Print button to start printing.
4

Magnify schematic / printed circuit board
diagrams - 2
(Pan & Zoom function)
The Pan & Zoom function lets you see which part of
a magnied diagram is being shown in a separate
window.
[Example using Adobe Reader X]
On the "View" menu, point to "Zoom", and then
click "Pan & Zoom".
• The Pan & Zoom window appears on the screen.
[Example using Adobe Reader 9]
On the "Tools" menu, point to "Select & Zoom",
and then click "Pan & Zoom Window".
Magnify schematic / printed circuit board
diagrams - 3
(Loupe Tool function)
The Loupe Tool function lets you magnify a specic
part of a diagram in a separate window.
[Example using Adobe Reader X]
On the "View" menu, point to "Zoom", and then
click "Loupe Tool".
• The Loupe Tool window appears on the screen.
[Example using Adobe Reader 9]
On the "Tools" menu, point to "Select & Zoom",
and then click "Loupe Tool Window".
5

SAFETY PRECAUTIONS
The following items should be checked for continued protection of the customer and the service technician.
leakage current check
Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis
resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the
power cord is less than 460 kohms, the set is defective.
Be sure to test for leakage current with the AC plug in both polarities, in addition, when the set's power is in each state
(on, off and standby mode), if applicable.
CAUTION Please heed the following cautions and instructions during servicing and
inspection.
◎Heed the cautions!
Cautions which are delicate in particular for servicing are
labeled on the cabinets, the parts and the chassis, etc. Be
sure to heed these cautions and the cautions described in
the handling instructions.
◎Cautions concerning electric shock!
(1) An AC voltage is impressed on this set, so if you touch
internal metal parts when the set is energized, you
may get an electric shock. Avoid getting an electric
shock, by using an isolating transformer and wearing
gloves when servicing while the set is energized, or
by unplugging the power cord when replacing parts,
for example.
(2) There are high voltage parts inside. Handle with extra
care when the set is energized.
◎ Caution concerning disassembly and assembly!
Through great care is taken when parts were
manufactured from sheet metal, there may be burrs on
the edges of parts. The burrs could cause injury if ngers
are moved across them in some rare cases. Wear gloves
to protect your hands.
◎Use only designated parts!
The set's parts have specic safety properties (re
resistance, voltage resistance, etc.). Be sure to use parts
which have the same properties for replacement. The
burrs have the same properties. In particular, for the
important safety parts that are indicated by the z mark
on schematic diagrams and parts lists, be sure to use the
designated parts.
◎ Be sure to mount parts and arrange the wires
as they were originally placed!
For safety seasons, some parts use tapes, tubes or other
insulating materials, and some parts are mounted away
from the surface of printed circuit boards. Care is also
taken with the positions of the wires by arranging them
and using clamps to keep them away from heating and
high voltage parts, so be sure to set everything back as it
was originally placed.
◎Make a safety check after servicing!
Check that all screws, parts and wires removed or
disconnected when servicing have been put back in
their original positions, check that no serviced parts have
deteriorate the area around. Then make an insulation
check on the external metal connectors and between the
blades of the power plug, and otherwise check that safety
is ensured.
(Insulation check procedure)
Unplug the power cord from the power outlet, disconnect
the antenna, plugs, etc., and on the power. Using a 500V
insulation resistance tester, check that the insulation
resistance value between the inplug and the externally
exposed metal parts (antenna terminal, headphones
terminal, input terminal, etc.) is 1MΩ or greater. If it is
less, the set must be inspected and repaired.
Many of the electric and the structural parts used in the
set have special safety properties. In most cases these
properties are difcult to distinguish by sight, and the use
of replacement parts with higher ratings (rated power
and withstand voltage) does not necessarily guarantee
that safety performance will be preserved. Parts with
safety properties are indicated as shown below on the
wiring diagrams and the parts list in this service manual.
Be sure to replace them with the parts which have the
designated part number.
(1) Schematic diagrams Indicated by the z mark.
(2) Parts lists Indicated by the z mark.
The use of parts other than the designated parts could
cause electric shocks, res or other dangerous situations.
CAUTION Concerning important safety
parts
6

NOTE FOR SCHEMATIC DIAGRAM
WARNING:
Parts indicated by the z mark have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.
CAUTION:
Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis resistance check. If
the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the set
is defective.
WARNING:
DO NOT return the set to the customer unless the problem is identied and remedied.
NOTICE:
ALL RESISTANCE VALUES IN OHM. k=1,000 OHM / M=1,000,000 OHM
ALL CAPACITANCE VALUES ARE EXPRESSED IN MICRO FARAD, UNLESS OTHERWISE INDICATED. P INDICATES MICRO-MICRO FARAD. EACH
VOLTAGE AND CURRENT ARE MEASURED AT NO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT TO CHANGE WITHOUT
PRIOR NOTICE.
NOTE FOR PARTS LIST
1. Parts indicated by "nsp" on this table cannot be supplied.
2. When ordering a part, make a clear distinction between "1" and "I" (i) to avoid mis-supplying.
3. A part ordered without specifying its part number can not be supplied.
4. Part indicated by " ★" mark is not illustrated in the exploded view.
WARNING: Parts indicated by the z mark have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.
INSTRUCTIONS FOR HANDLING SEMI-CONDUCTORS AND OPTICAL UNIT
Electrostatic breakdown of the semi-conductors or optical pickup may occur due to a potential difference caused by
electrostatic charge during unpacking or repair work.
1. Ground for Human Body
Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged
on the body.
2. Ground for Workbench
Be sure to place a conductive sheet or copper plate with proper grounding (1 MΩ) on the workbench or other surface,
where the semi-conductors are to be placed. Because the static electricity charge on clothing will not escape through the
body grounding band, be careful to avoid contacting semi-conductors with your clothing
<Incorrect>
CBA
Grounding Band
Conductive Sheet or
Copper Plate
1MΩ
1MΩ
<Correct>
CBA
7

Personal notes:
8

TECHNICAL SPECIFICATIONS
nAudio section
• Power amplier
Rated output :
Front :
110 W + 110 W ( 8 Ω, 20 Hz - 20 kHz with 0.08 % T.H.D.)
150 W + 150 W ( 6 Ω, 1 kHz with 0.7 % T.H.D.)
Center :
110 W ( 8 Ω, 20 Hz - 20 kHz with 0.08 % T.H.D.)
150 W ( 6 Ω, 1 kHz with 0.7 % T.H.D.)
Surround :
110 W + 110 W ( 8 Ω, 20 Hz - 20 kHz with 0.08 % T.H.D.)
150 W + 150 W ( 6 Ω, 1 kHz with 0.7 % T.H.D.)
Surround back / Height1 / Front wide :
110 W + 110 W ( 8 Ω, 20 Hz - 20 kHz with 0.08 % T.H.D.)
150 W + 150 W ( 6 Ω, 1 kHz with 0.7 % T.H.D.)
Output connectors : 4 - 16 Ω
nAnalog section
Input sensitivity/Input impedance : 200 mV / 47 kΩ
Frequency response : 10 Hz - 100 kHz — +1, -3 dB (Direct mode)
S/N : 100 dB (IHF-A, Direct mode)
Distortion : 0.005 % (20 Hz – 20 kHz) (Direct mode)
Rated output : 1.2 V
nDigital section
D/A output : Rated output — 2V (at 0 dB playback)
Total harmonic distortion — 0.008 % (1 kHz, 0 dB )
S/N ratio — 102 dB
Dynamic range — 100 dB
Digital input : Format — Digital audio interface
nPhono equalizer section
Input sensitivity : 2.5 mV
RIAA deviation : ±1 dB (20 Hz to 20 kHz)
S/N ratio : 74 dB (IHF-A)
Distortion factor : 0.03 % (1 kHz, 3 V)
nVideo section
• Standard video connectors
Input/output level and impedance : 1 Vp-p, 75 Ω
Frequency response : 5 Hz - 10 MHz — 0, –3 dB
• Color component video connector
Input/output level and impedance : Y signal — 1 Vp-p, 75 Ω
PB / CB signal — 0.7 Vp-p, 75 Ω
PB / CB signal — 0.7 Vp-p, 75 Ω
Frequency response : 5 Hz - 60 MHz — 0, –3 dB
nTuner section
(Note : μV at 75 Ω, 0 dBf = 1 x 10–15 W)
Reception frequency range : FM 87.5 MHz - 107.9 MHz (for U)
FM 87.5 MHz - 108.0 MHz (for N)
AM 520 kHz - 1710 kHz (for U)
AM 522 kHz - 1611 kHz (for N)
Effective sensitivity : FM 1.2 μV (12.8 dBf)
AM 18 μV
50 dB sensitivity : MONO ― 2.8 μV (20.2 dBf)
S/N ratio : MONO ― 70 dB (IHF–A weighted, Direct mode)
STEREO ― 67 dB (IHF–A weighted, Direct mode)
Distortion : MONO ― 0.7 % (1 kHz)
SRETEO ― 1.0 % (1 kHz)
nWireless LAN section
Network type (wireless LAN standard) : Conforming to IEEE 802.11b
Conforming to IEEE 802.11g
Conforming to IEEE 802.11n
(Wi-Fi® compliant)z1
Security : WEP 64 bit, WEP 128 bit
WPA/WPA2-PSK (AES)
WPA/WPA2-PSK (TKIP)
Radio frequency : 2.4 GHz
No. of channels : 1 - 11 ch (for U)
1 - 13 ch (for N)
z1 The Wi-Fi® CERTIFIED Logo and the Wi-Fi CERTIFIED On-Product Logo
are registered trademarks of the Wi-Fi Alliance.
nBluetooth section
Communications system : Bluetooth Version 2.1 + EDR
(Enhanced Data Rate)
Transmission power : Maximum 2.5 mW (Class 2)
Maximum communication range : Approx. 32.8 ft/10 m in line of sightz2
Frequency band : 2.4 GHz band
Modulation scheme : FHSS (Frequency-Hopping Spread Spectrum)
Supported proles : A2DP (Advanced Audio Distribution Prole)1.2
AVRCP (Audio Video Remote Control Prole)1.4
Corresponding codec : SBC, AAC
Transmission range (A2DP) : 20 Hz - 20,000 Hz
z2 The actual communication range varies depending on the inuence of
such factors as obstructions between devices, electromagnetic waves
from microwave ovens, static electricity, cordless phones, reception
sensitivity, antenna performance, operating system, application
software etc.
nGeneral
Power supply : (for U) : AC 120 V, 60 Hz
(for N) : AC 230 V, 50 Hz / 60 Hz
Power consumption : 650 W
Power consumption in standby mode : 0.2 W
Power consumption in CEC standby mode : 0.5 W
Power consumption in network standby mode : 2.7 W
For purposes of improvement, specications and design are subject to
change without notice.
9

3/4
(18)
5/8
(14)
3/4
(18)
1 3/8
(32)
2 1/8
(53) 9 7/8 (248)
15 3/8 (388)
1 7/8
(47)
7/8
(22)
9 1/8 (229) 6 3/8 (161) 5 7/8 (147) 13 3/4 (349)
15 3/4 (398)
2 (50)13 1/2 (340)
17 3/8 (440)
2 (50)
2 1/4
(55)
DIMENSION
Unit : in. (mm)
Weight : 25 lbs 9 oz (11.6 kg)
10

CAUTION IN SERVICING
Initializing This Unit
Make sure to initialize this unit after replacing the microcomputer or any peripheral equipment, or the digital PCB.
1. Press the power button to turn off the power.
2. While holding down buttons "TUNER PRESET -" and "TUNER PRESET +" simultaneously, press the power button
to turn on the power.
3. Release the buttons after conrming that the display ashes at 1-second intervals.
＊ The unit is initialized.
NOTE：• If the unit fails to enter the service mode in step 3, repeat the procedure from step 1.
• Initializing the device restores the customized settings to the factory settings. Write down your settings in advance and
recongure the settings after initialization.
JIG FOR SERVICING
Use the following jigs (extension cable kit) when repairing the PCBs.
Order with your dealer for the jigs your dealer if necessary.
8U-110084S : EXTENSION UNIT KIT : 1Set
8U-110136S : EXTENSION UNIT KIT : 1Set
(See page 73)
TUNER
PRESET CH -
XTUNER
PRESET CH +
11

DISASSEMBLY
• Remove each part following the ow below.
• Reassemble the removed parts in the reverse order.
• Read "Precautions During Work" before reassembling the removed parts.
• If wire bundles are removed or moved during adjustment or part replacement, reshape the wires after completing
the work. Failure to shape the wires correctly may cause problems such as noise.
FRONT PANEL ASSY
See "DISASSEMBLY"
1. FRONT PANEL ASSY
and "EXPLODED VIEW"
FRONT PCB
Ref. No. of EXPLODED VIEW : C1
GUIDE TOP PCB
Ref. No. of EXPLODED VIEW : C10
FRONT CONT FFC PCB
Ref. No. of EXPLODED VIEW : C4
F_HDMI PCB
Ref. No. of EXPLODED VIEW : C5
HP PCB
Ref. No. of EXPLODED VIEW : C45
TOP COVER
MAIN TRANS
See "DISASSEMBLY"
8. MAIN TRANS
and "EXPLODED VIEW"
MAIN TRANS
Ref. No. of EXPLODED VIEW : C19
RADIATOR ASSY
See "DISASSEMBLY"
2. RADIATOR ASSY
and "EXPLODED VIEW"
GUIDE L PCB
Ref. No. of EXPLODED VIEW : C7
AMP PCB
Ref. No. of EXPLODED VIEW : C8
HEATSINK
Ref. No. of EXPLODED VIEW : M14
DIGITAL PCB ASSY
See "DISASSEMBLY"
3. DIGITAL PCB ASSY
and "EXPLODED VIEW"
DIGITAL PCB
Ref. No. of EXPLODED VIEW : C21
CY920 MODULE ASSY
Ref. No. of EXPLODED VIEW : C22
INPUT HDAM PCB ASSY
See "DISASSEMBLY"
5. INPUT HDAM PCB ASSY
and "EXPLODED VIEW"
INPUT PCB
Ref. No. of EXPLODED VIEW : C39
CONNECT-2 PCB
Ref. No. of EXPLODED VIEW : C44
CONNECT-3 PCB
Ref. No. of EXPLODED VIEW : C43
CONNECT-4 PCB
Ref. No. of EXPLODED VIEW : C42
HDAM PCB
Ref. No. of EXPLODED VIEW : C41
VIDEO PCB ASSY
See "DISASSEMBLY"
4. VIDEO PCB ASSY
and "EXPLODED VIEW"
VIDEO PCB
Ref. No. of EXPLODED VIEW : C20
SPK PCB ASSY
See "DISASSEMBLY"
6. SPK PCB ASSY
and "EXPLODED VIEW"
SPK PCB
Ref. No. of EXPLODED VIEW : C29
SPK FW PCB
Ref. No. of EXPLODED VIEW : C@@
FUSE PCB
Ref. No. of EXPLODED VIEW : C27
FRT CNT PCB
Ref. No. of EXPLODED VIEW : C26
SIDE CONT PCB
Ref. No. of EXPLODED VIEW : C28
SMPS PCB
See "DISASSEMBLY"
7. SMPS PCB
and "EXPLODED VIEW"
SMPS PCB
Ref. No. of EXPLODED VIEW : C11
12

Explanatory Photos for DISASSEMBLY
• For the shooting direction of each photos used in this manual, see the photo below.
• A, B, C and D in the photo below indicate the shooting directions of photos.
• The photographs with no shooting direction indicated were taken from the top of the unit.
• Photos of SR6010 U are used in this manual.
The viewpoint of each photograph
(Shooting direction : X) [View from the top]
Front side
↑Shooting direction: A↑
↓Shooting direction: B↓
↓Shooting direction: D↓
↑Shooting direction: C↑
13

1. FRONT PANEL ASSY
Proceeding : TOP COVER →FRONT PANEL ASSY
(1) Remove the screws.
(2) Remove the screws. Cut the wire clamp, then remove the connector. Remove the FFC.
2. RADIATOR ASSY
Proceeding : TOP COVER →FRONT PANEL ASSY →RADIATOR ASSY
(1) Remove the screws.
(2) Cut the wire clamp, then remove the connector wire. Remove the screws.
View from the bottom
x5
FFC FFC
CN102
CN104
x1 CUT x4
Shooting direction: A
x3
↑Shooting direction: D↑↑Shooting direction: C↑
x2 x2
CN461
CN701 CN702 CN704
CN703
CN704
CUT
CUT
14

3. DIGITAL PCB
Proceeding : TOP COVER →BACK CHASSIS →DIGITAL PCB
(1) Remove the screws.
(2) Cut the wire clamp, then remove the connector. Remove the FFC.
(3) Remove the connector.
Shooting direction: A
x13
x37
x2
CN704 FFC FFC
CN321
CN903
x2 CUTx5
STYLE PIN
BN24A BN26A BN25A BN21A
BN23A
BN27A
15

4. VIDEO PCB
Proceeding : TOP COVER →BACK CHASSIS →DIGITAL PCB →VIDEO PCB
(1) Cut the wire clamp, then remove the connector. PCB HOLDER を外します。
5. INPUT HDAM PCB
Proceeding : TOP COVER →BACK CHASSIS →DIGITAL PCB →VIDEO PCB →INPUT HDAM PCB
(1) Remove the screws. Remove the connector.
BN21B
BN28B
BN27B
CUT x4
PCB HOLDER
x1
BN26C
BN24C
BN64C
BN23C
CN706
From AMP PCB
STYLE PIN
16

6. SPK PCB
Proceeding : TOP COVER →BACK CHASSIS →DIGITAL PCB →VIDEO PCB →INPUT HDAM PCB
→SPK PCB
(1) Remove the screws.
(2) Cut the wire clamp, then remove the connector.
(3) Remove the screws.
7. SMPS PCB
Proceeding : TOP COVER →BACK CHASSIS →DIGITAL PCB →SMPS PCB
See "EXPLODED VIEW" for instructions on removing the SMPS PCB.
8. TRANS POWER
Proceeding : TOP COVER →BACK CHASSIS →DIGITAL PCB →TRANS POWER
See "EXPLODED VIEW" for instructions on removing the transformer (TRANS).
View from the bottom
x1
CN703
CN461
CN704
CN702
CN701
CUT
x7
x2
x3
x1
17

SPECIAL MODE
Special mode setting button
b ABC
b AB
b AB
No. Mode Button A Button B Button C Descriptions

   



  
    
 



 



     

   

    



 
     
   
  
 








    



    



 



  
 



  

 



  
 



 



TUNER
PRESET CH + STATUSZONE2 SOURCE
M-DAX
XTUNER
PRESET CH - DIMMER SOUND MODE
f


1. Version Display Mode
1.1. Actions
Version information is displayed when the device is started in this mode.
1.2. Starting up
While holding down buttons "DIMMER" and "STATUS" simultaneously, press the power button to turn on the power.
then press the "STATUS" button to display the information in section 1.3 on the display.
b The version list is also displayed on GUI while the version is displayed on the display.
1.3. Display Order
Error information("See "1.4. Error display") → q Model destination information, Serial Number
→ w Firmware Package Version → e Main µ-com, Main 1st Boot Loader Version → r DSP1/2/3/4 ROM
→ t Audio, Video PLD → y GUI SFLASH → u Ethernet 1st Boot Loader, Hardware ID
→ i Ethernet 2nd Boot Loader, Rhapsody Flag → o Ethernet IMAGE → Q0 Ethernet MAC ADDRESS information
→ Q1 BT MAC ADDRESS information → Q2 MultEQ Pro APP (Displayed when Audyssey Pro is complete)
→ Q3 MultEQ Pro ICL (Displayed when Audyssey Pro is complete)
q Model destination information, Serial Number：
FLD
L1 SR6010 U
L2 SN-****
L3 * * * * * *
FLD L1 SR6010 N
w Firmware Package Version：
FLD
L1 PACKAGE
L2
L3 * * * *
e Main µ-com, Main 1st Boot Loader Version:
FLD
L1 M A i n
L2 * * * *
L3 BL-**.**
r DSP1/2/3/4 ROM :
FLD
L1 D 1
–
**.**
L2
L3 D 2
–
**.**
FLD
L1 D 3
–
**.**
L2
L3 D 4
–
**.**
t Audio, Video PLD :
FLD
L1 A.PLD
L2
L3 **.**
19

y GUI SFLASH :
FLD
L1 G U I
L2 @@$\****
L3
@ ： Model code, $ ： Brand code, \ ： Region code (U=1, N=2, K=5, F=4)
u Ethernet 1st Boot Loader, Hardware ID :
FLD
L1 N E T F B L
L2 ********
L3 -AA
AA : Hardware ID
i Ethernet 2nd Boot Loader, Rhapsody Flag :
FLD
L1 N E T S B L
L2 ********
L3 *****-BB
BB : Rhapsody Flag
o Ethernet IMAGE :
FLD
L1 N E T I M G
L2 ********
L3 *****
Q0 Ethernet MAC ADDRESS information：
FLD
L1 N E T M A C
L2 ******
L3 -******
Q1 BT MAC ADDRESS information：
FLD
L1 B T M A C
L2 ******
L3 -******
Q2 MultEQ Pro APP :
FLD
L1 E Q A P P
L2 **.**.**
L3 .****
Q3 MultEQ Pro ICL :
FLD
L1 E Q I C L
L2 **.**.**
L3 .****
20