MarCELL SPuck Manual

Need Help? Contact us today [phone] or [e-mail]
Instruction Guide
The SPuck water sensor enhances the monitoring capabilities of the MarCELL by
providing water detection alarms.
Communicates wirelessly with the MarCELL device to instantly indicate
presence of water
Operates for years on a single CR2025 coin cell battery
Monitors battery life and will report when it’s getting low
Up to 16 SPucks can communicate with one MarCELL
Communication distance varies depending on walls and objects in the path.
Generally the range is 50 to 300 feet.

Need Help? Contact us today [phone] or [e-mail]
Installation
Step 1 –Register your SPuck
Make sure your MarCELL is registered and operating properly.
Flip your SPuck over and locate the device ID
Go to www.sensoredlife.com
Log in to your account
Select”My Devices”then on the dashboard of the desired MarCELL
click the SPuck icon
Select “Add SPuck” and follow the instructions
Step 2 –Wait for SPuck information to upload to the MarCELL
After registering the SPuck, the information will be sent to your
MarCELL unit. The LED on the front of the MarCELL will blink. This
process will take about 30 seconds and will be complete when the LED
turns back to solid green
NOTE: If your MarCELL was not plugged in when you registered the
SPuck, the new SPuck information will be automatically updated when
your MarCELL is plugged in.
Step 3 –Select a Location and Test
Place the SPuck in the location where it will be used. Press and
release the test button. The button LED will light up and flash four
times. Quickly
The SPuck will have sent a test message to the MarCELL. If the
MarCELL successfully receives this message, it will start to blink a blue
status LED for 30 seconds. If you see the blinking blue LED you will
know your MarCELL and SPuck are communicating properly
If the LED on the MarCELL is not blinking blue, please try the following
Please be sure you have completed steps 1 and 2 and your SPuck has
been registered
Try moving the MarCELL and SPuck closer together
Repeat the test sequence

Need Help? Contact us today [phone] or [e-mail]
Step 4 –Place Into Service
Place the SPuck on a flat surface. If water comes in contact with either
of the water sensors, the SPuck will send an alarm to the MarCELL.
When transmitting the SPuck’s LED will flash quickly.
Once a SPuck detects the presence of water and sends the alarm
signal, it will be deactivated to preserve battery life. When the water
that caused the alarm is no longer present, the SPuck will
automatically reset after 15 minutes. You can also rearm the SPuck by
making sure the sensors are dry and pressing and releasing the test
button. When the button blinks blue your SPuck is back in service and
ready to detect water again.
NOTE: The SPucks water detection circuit is designed to be very
sensitive. If the sensors remain wet after the test button press the
SPuck will indicate this by flashing 1 short blue pulse every 5 seconds.
If you see this, please dry the sensors more thoroughly or wait a few
minutes for them to dry off. When the sensor has reset the 1 pulse
flash will stop.
Changing the battery
Turn the SPuck over so the made in the USA label is facing towards
you
Slide the back cover up ¼” – this will take a little force and you will
hear a click
Lift the back cover off
Slide the CR2025 coin cell down and replace it with the new battery. If
this is done properly you will see the button flash 4 times.
Replace the back cover
Technical Specifications
Battery : CR2025 Coin Cell
Radio : 915Mhz ISM band, 19.2k baud
Size : 1.42”(width) 1.92”(length) 0.40”(height)

Need Help? Contact us today [phone] or [e-mail]
Problem
Actions
Blue LED fails to light
when pressing Test
button
Make sure the battery is properly installed with the
+ sign on top
Make sure the battery indicator on the SPuck page
of the dashboard is green
Replace the CR2025 battery
SPuck not
communicating with
the MarCELL
Make sure the MarCELL is registered and has a
solid green light
Make sure the SPuck is registered to the correct
MarCELL device by checking the dashboard
Make sure the blue LED on the front of the
MarCELL flashes when pressing the test button
Move the MarCELL closer to the SPuck to test
whether there is a range issue
SPuck not detecting
water
Press the Test button to make sure the SPuck is
reset
If the SPuck is still detecting the presence of water
after the test button is pressed the Test LED will
blink quickly 1 time every 5 seconds. If this occurs
dry the water sensors completely and the LED
flashing will stop
Make sure the SPuck is on a smooth surface and
the water sensors can come into contact with the
water