Mark Of Fitness XM-4434 User manual

XM-4434
Owner’s Manual
!CAUTION
Read all precautions and
instructions in this manual before
using this equipment.
POWER TOWER

2
Table of Contents
Important Safety Information 3
Assembly 4-7
Parts List 8
Exploded View 9
Warranty Information 10

3
Important Safety Information
Please read all instructions carefully before using this product.
SAFETY TIPS
Consult with your physician before engaging in any vigorous exercise. Know your heart rate
and/or pulse as well as your physician-recommended heart rate training zone. Proper medical
clearance is recommended for anyone beginning an exercise program especially if you are 35
years of age or older or suffer from heart respiratory problems.
- Warm-up before any exercise program with 8 minutes of aerobic-like activity followed
by stretching from head to toe.
- Wear comfortable clothes that allow freedom of movement and are not tight or
restricting.
- Wear comfortable shoes made with good support and non-slip soles.
- Breath naturally, never holding your breath during an exercise.
- Perform exercises consistently with proper technique and pass through a full range of
motion.
- Increase resistance by adding heavier weights. Decrease resistance by using lighter
weights.
- Always use a spotter for safety.
- Avoid over-training. You should be able to carry on a conversation while exercising.
- After an exercise session. Cool down with slow stretching, cycling or walking.
EXERCISE DEFINITIONS:
Sets: A set is one complete routine of exercises. Complete 1-3 sets for each exercise.
Repetitions: (referred to as reps) Is the number of times you perform an exercise in a row.
We recommend beginning with 6 reps and increasing up to 12 reps as indicated below.
Novice: Start with one set of 8-12 reps. Once you can complete the entire set of 12 reps con-
secutively, progress to the intermediate level.
Intermediate: Complete 2 sets of 8-12 reps once you can complete two sets of 12 reps con-
secutively, progress to the advanced level.
Advanced: Complete 3 sets of 12 reps
DISCLAIMER:
XMark Fitness is not responsible for the misuse of any of its products or for any injury sustained
while using any product. The consumer uses any or all of Products at
their own risk.
BEFORE YOU BEGIN:
Before you begin assembly of your product, please take a moment to review the
hardware and parts list on the following pages. Each part has been illustrated and numbered
for easy identification.
Check this list against the contents of your package to make sure you have all required parts.
If any parts are missing, please do not return this product to the store. Contact our service
department immediately at
1.800.719.4605 and we will rush you any parts you may require.
XMark Fitness
XMark Fitness
XMark Fitness

4
Assembly
M10 Nylon Locknut (C1)
M8 Washer (B2)
M8 x 70mm Bolt (A4) M10 x 70mm Bolt (A2
)
M10 Washer (B1)
Hardware Identifier
See the drawings below to identify the hardware used in the assembly. The number in paren-
theses is the reference number of the part.
Note: Some hardware may be pre-installed in some parts.
M10 x 20mm Bolt (A1) M10 x 55mm Bolt (A3)
M8 x 40mm Bolt (A5)

5
NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled.
Place the Left and Right Base (1 & 2) parallel to each other. Connect the
Bottom Brace (9) to the Left and Right Base (1 & 2). Secure them with four
M10x70 Bolts (A2), and four M10 Nylon Locknuts (C1).
Insert the two Lower Upright Tubes (6) into the Left and Right Base (1 & 2).
Secure them using eight M10 x 20 Bolts (A1) and eight Washers D10 (B1).
Insert the Lower Support Bars (4) between the Base (1 & 2) and the Lower
Upright Tubes (6). Secure them with four M10 x 70 Bolts (A2)
Nylon Locknuts (C1).
STEP 1
Assembly
1
6
6
4C1
C1
9
C1
A2
2
A2
A1
B1
A1
A2
and four M10

6
NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled.
A2
A2
C1 C1
A2
A1
B1
C1
A1
A1
C1
A3
A3
B1
B1
C1
18
11
11
13
14
Connect the Pull-up Bar (18) to the both of the Upper Upright Tubes (11) and secure
them with two M10 x 55 Bolts (A3) and two Washers D10 (B1).
Connect two Upper Upright Tubes (11) to the Lower Upright Tubes (6) and secure
them using four M10 x 20 Bolts (A1) and four Washers D10 (B1).
Attach the two Extend Arms (13) through the joints of the Upper and Lower Upright
Tubes (11 & 6) to the Upper Cross Brace (12). Secure them with four M10 x20 Bolts
(A1), two M10x70 Bolts (A2),and two M10 Nylon Locknuts (C1).
Connect the two Upper Support Bars (14) to both the Extend Arms (13) and the
Lower Upright Tubes (6). Secure them using four M10 x 70 Bolts (A2),
M10 Nylon Locknuts (C1).
STEP 2
Assembly
A2
A2
A1
B1
6
12
and four

7
STEP 3
A4
B2
A5
B2
19
20
Attach the two Armrests (19) to each of the Extend Arms (13) and secure them
with four M8x70 Bolts (A4) and four Washers D8 (B2).
Attach the Backrest Board (20) to the Upper Cross Brace (12) and secure it with
two M8x40 Bolts (A5) and two Washers D8 (B2).
NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled.
Assembly
13
12

8
REF # PART # DESCRIPTION QTY
1 223-00313 LEFT/RIGHT BASE 1
2 223-00313 LEFT/RIGHT BASE 1
3 206-00227 SHORT FOAM GRIP 6
4 223-00317 LOWER SUPPORT BAR 2
6 223-00314 LOWER UPRIGHT 2
8 206-00228 ROUND PLUG, 25X1.5 2
9 223-00311 BOTTOM CROSS BRACE 1
10 206-00161 ROUND INNER PLUG, 25x2 6
11 223-00309 UPPER UPRIGHT TUBE 2
12 223-00316 UPPER CROSS BRACE 1
13 223-00312 EXTENDED ARM 2
14 219-00225 UPPER SUPPORT BAR 2
15 206-00226 MID FOAM GRIP, 2
16 206-00113 LONG FOAM GRIP 1
17 206-00116 CONNECTIVE HEAD 2
18 223-00310 PULL UP BAR 1
19 228-00251 PAD, ARM 2
20 225-00252 PAD, BACK 1
21 206-00072 END CAP 4
206-00071 2" SQUARE SLEEVE 2
206-00229 PROTECTIVE COVER 2
A1 202-00296 HEX BOLT, M10X20 16
A2 202-00294 HEX BOLT, M10X70 14
A3 202-00436 BOLT M10X55 2
A4 202-00290 BOLT, M8X70 4
A5 202-00291 BOLT, M8X40 2
B1 202-00420 WASHER 10 14
B2 202-00421 WASHER 8 6
C1 202-00168 M10 Nylon Locknut 14
# 202-00195 BOLT PACK 1
XM-4434 Parts List Rev A
Parts List
5
7

9
Exploded View
A5
B2
B1
7
7
3
3
19
19
21
21
21
21
5
5
A2
6
A2

This warranty applies only in the United States and Canada to products manufactured by XMark®under the XMark®brand name. This
SURGXFW LV EDFNHG E\ D OLIHWLPH LQKRPH ZDUUDQW\ H[FOXGLQJ H[SHQGDEOH SDUWV VXFK DV SDLQW ¿QLVK DQG YLQ\O 7KLV ZDUUDQW\ H[WHQGV
only to you, the original purchaser. It is not transferable to anyone who subsequently purchases the product from you.
XMark®ZDUUDQWV WKDW WKH SURGXFW \RX KDYH SXUFKDVHG RU UHFHLYHG IRU QRQFRPPHUFLDO SHUVRQDO IDPLO\ RU KRXVHKROG XVH IURP
XMark®is free from defects in materials or workmanship under normal use during the warranty period. Your sales receipt, showing the
date of purchase of the product, is your proof of the date of purchase. This warranty becomes VALID ONLY if the product is assembled
and/or installed according to the instructions and/or directions included with the product.
ƔDuring the warranty period XMark®will repair or replace (at the discretion of XMark® WKH SURGXFW LI LW EHFRPHV GHIHFWLYH
malfunctions, or otherwise fails to conform with this warranty under normal use. In repairing the product, XMark®may replace
GHIHFWLYH SDUWV ZLWK QHZ RU DW WKH GLVFUHWLRQ RI ;0DUN® VHUYLFHDEOH XVHG SDUWV WKDW DUH HTXLYDOHQW WR QHZ SDUWV LQ SHUIRUPDQFH
All exchanged parts and products replaced under this warranty will become the property of XMark®. XMark®UHVHUYHV WKH ULJKW WR
FKDQJH PDQXIDFWXUHUV RI DQ\ SDUW WR FRYHU DQ\ H[LVWLQJ ZDUUDQW\
ƔThis warranty DOES NOT COVER shipping and handling charges, export taxes, custom duties and taxes, or any other charges
DVVRFLDWHG ZLWK WUDQVSRUWDWLRQ RI WKH SDUWV RU SURGXFW 7R REWDLQ ZDUUDQW\ VHUYLFH \RX PXVW FRQWDFW DQ ;0DUN®FXVWRPHU VHUYLFH
UHSUHVHQWDWLYH DW WKH SKRQH QXPEHU ORFDWHG LQ WKH PDQXDO $Q\ SDUWV GHWHUPLQHG WR EH GHIHFWLYH PXVW EH UHWXUQHG WR ;0DUN®
WR REWDLQ ZDUUDQW\ VHUYLFH <RX PXVW SUHSD\ DQ\ VKLSSLQJ FKDUJHV H[SRUW WD[HV FXVWRP GXWLHV DQG WD[HV RU DQ\ RWKHU FKDUJHV
associated with transportation of the parts or product. In addition, you are responsible for insuring any parts or product shipped or
returned. You assume the risk of loss during shipment. You must present XMark®with proof-of-purchase documents (including the
GDWH RI SXUFKDVH $Q\ HYLGHQFH RI DOWHUDWLRQ HUDVXUH RU IRUJHU\ RI SURRIRISXUFKDVH GRFXPHQWV ZLOO EH FDXVH WR YRLG WKLV ZDUUDQW\
ƔThis warranty does not extend to any product not manufactured by XMark®. This Lifetime in-home warranty does not extend to
DQ\ SURGXFW WKDW KDV EHHQ GDPDJHG RU UHQGHUHG GHIHFWLYH D DV D UHVXOW RI DFFLGHQW PLVXVH RU DEXVH E E\ WKH XVH RI SDUWV QRW
manufactured by XMark® RU F E\ PRGL¿FDWLRQ RI WKH SURGXFW 3URGXFW RQ ZKLFK WKH VHULDO QXPEHU KDV EHHQ GHIDFHG RU UHPRYHG
LV QRW HOLJLEOH IRU ZDUUDQW\ VHUYLFH 6KRXOG DQ\ SURGXFW VXEPLWWHG IRU ZDUUDQW\ VHUYLFH EH IRXQG LQHOLJLEOH DQ HVWLPDWH RI UHSDLU FRVW
will be furnished and the repair will be made if requested by you upon receipt by XMark®of payment or acceptable arrangements for
payment.
(;&(37 $6 (;35(66/< 6(7 )257+ ,1 7+,6 :$55$17< XMARK®0$.(6 12 27+(5 :$55$17,(6 (;35(66(' 25
,03/,(' ,1&/8',1* $1< ,03/,(' :$55$17,(6 2) 0(5&+$17$%,/,7< $1' ),71(66 )25 $ 3$57,&8/$5 385326(
XMARK®(;35(66/< ',6&/$,06 $// :$55$17,(6 127 67$7(' ,1 7+,6 /,)(7,0( ,1+20( :$55$17< $1< ,03/,('
:$55$17,(6 7+$7 0$< %( ,0326(' %< /$: $5( /,0,7(' 72 7+( 7(506 2) 7+,6 :$55$17< 1(,7+(5 XMARK®NOR
$1< 2) ,76 $)),/,$7(6 6+$// %( 5(63216,%/( )25 ,1&,'(17$/ 25 &216(48(17,$/ '$0$*(6 620( 67$7(6 '2 127
$//2: /,0,7$7,216 21 +2: /21* $1 ,03/,(' :$55$17< /$676 25 7+( (;&/86,21 25 /,0,7$7,21 2) ,1&,'(17$/ 25
&216(48(17,$/ '$0$*(6 62 7+( $%29( /,0,7$7,216 25 (;&/86,216 0$< 127 $33/< 72 <28
7KLV /LIHWLPH ,Q+RPH :DUUDQW\ JLYHV \RX VSHFL¿F OHJDO ULJKWV DQG \RX PD\ DOVR KDYH RWKHU ULJKWV WKDW PD\ YDU\ IURP VWDWH WR VWDWH
This is the only expressed warranty applicable to XMark®branded products. XMark®neither assumes nor authorizes anyone to
assume for it any other expressed warranty.
WARRANTY
4400 Nitro Series
intended for residential use only
7600 Carbon Series
intended for light institutional and/or residential use