Mark Of Fitness XM-4446 User manual

XM-4446
Owner’s Manual
!CAUTION
Read all precautions and
instructions in this manual before
using this equipment.
POWER TOWER

2
Table of Contents
Important Safety Information 4
Before You Start 3
Assembly 5-8
Parts List 9
Exploded View 10

MODEL: XM-4446
XM-4446
This manual will guide you through the assembly process. If at any time you
are having trouble with the assembly or use of this product, then please contact
When calling please have the following product information available:
Model Name :
Date Mfg.:
Serial #
Model Name Decal Location
Before You Start
QUESTIONS?
CALL 1-800-719-4605
Monday-Friday
8:30 a.m.-5:00 p.m.
(Central Standard Time)
MAILING ADDRESS
XMark Fitness, LLC
2791 Valley View Drive
Shreveport, LA 71108
3
THANK YOU for making this unit a part of your exercise
program.
XMARK Fitness assures the very best in value,
appearance, durability and biomechanics.
XMARK FITNESS SERIES
us at our
XMARK Fitness help line. We have trained service technicians on site to
take care of you, our valued customer.
For Warranty information please visit www.xmarkfitness.com.

4
Important Safety Information
Please read all instructions carefully before using this product.
SAFETY TIPS
Consult with your physician before engaging in any vigorous exercise. Know your heart rate
and/or pulse as well as your physician-recommended heart rate training zone. Proper medical
clearance is recommended for anyone beginning an exercise program especially if you are 35
years of age or older or suffer from heart respiratory problems.
- Warm-up before any exercise program with 8 minutes of aerobic-like activity followed
by stretching from head to toe.
- Wear comfortable clothes that allow freedom of movement and are not tight or
restricting.
- Wear comfortable shoes made with good support and non-slip soles.
- Breath naturally, never holding your breath during an exercise.
- Perform exercises consistently with proper technique and pass through a full range of
motion.
- Increase resistance by adding heavier weights. Decrease resistance by using lighter
weights.
- Always use a spotter for safety.
- Avoid over-training. You should be able to carry on a conversation while exercising.
- After an exercise session. Cool down with slow stretching, cycling or walking.
EXERCISE DEFINITIONS:
Sets: A set is one complete routine of exercises. Complete 1-3 sets for each exercise.
Repetitions: (referred to as reps) Is the number of times you perform an exercise in a row.
We recommend beginning with 6 reps and increasing up to 12 reps as indicated below.
Novice: Start with one set of 8-12 reps. Once you can complete the entire set of 12 reps con-
secutively, progress to the intermediate level.
Intermediate: Complete 2 sets of 8-12 reps once you can complete two sets of 12 reps con-
secutively, progress to the advanced level.
Advanced: Complete 3 sets of 12 reps
DISCLAIMER:
XMark Fitness is not responsible for the misuse of any of its products or for any injury sustained
while using any product. The consumer uses any or all of Products at
their own risk.
BEFORE YOU BEGIN:
Before you begin assembly of your product, please take a moment to review the
hardware and parts list on the following pages. Each part has been illustrated and numbered
for easy identification.
Check this list against the contents of your package to make sure you have all required parts.
If any parts are missing, please do not return this product to the store. Contact our service
department immediately at
1.800.719.4605 and we will rush you any parts you may require.
XMark Fitness
XMark Fitness
XMark Fitness

5
Assembly
M10 Nylon Locknut (C1)
M8 Washer (B2)
M8 x 70mm Bolt (A4) M10 x 70mm Bolt (A2
)
M10 Washer (B1)
Hardware Identifier
See the drawings below to identify the hardware used in the assembly. The number in paren-
theses is the reference number of the part.
Note: Some hardware may be pre-installed in some parts.
M10 x 20mm Bolt (A1) M10 x 55mm Bolt (A3)
M8 x 40mm Bolt (A5)

6
NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled.
Place the Left and Right Base (1 & 2) parallel to each other. Connect the
Bottom Brace (9) to the Left and Right Base (1 & 2). Secure them with four
M10x70 Bolts (A2), and four M10 Nylon Locknuts (C1).
Insert the two Lower Upright Tubes (6) into the Left and Right Base (1 & 2).
Secure them using eight M10 x 20 Bolts (A1) and eight Washers D10 (B1).
Insert the Lower Support Bars (4) between the Base (1 & 2) and the Lower
Upright Tubes (6). Secure them with four M10 x 70 Bolts (A2)
Nylon Locknuts (C1).
STEP 1
Assembly
1
6
6
4C1
C1
9
C1
A2
2
A2
A1
B1
A1
A2
and four M10

7
NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled.
A2
A2
C1 C1
A2
A1
B1
C1
A1
A1
C1
A3
A3
B1
B1
C1
18
11
11
13
14
Connect the Pull-up Bar (18) to the both of the Upper Upright Tubes (11) and secure
them with two M10 x 55 Bolts (A3) and two Washers D10 (B1).
Connect two Upper Upright Tubes (11) to the Lower Upright Tubes (6) and secure
them using four M10 x 20 Bolts (A1) and four Washers D10 (B1).
Attach the two Extend Arms (13) through the joints of the Upper and Lower Upright
Tubes (11 & 6) to the Upper Cross Brace (12). Secure them with four M10 x20 Bolts
(A1), two M10x70 Bolts (A2),and two M10 Nylon Locknuts (C1).
Connect the two Upper Support Bars (14) to both the Extend Arms (13) and the
Lower Upright Tubes (6). Secure them using four M10 x 70 Bolts (A2),
M10 Nylon Locknuts (C1).
STEP 2
Assembly
A2
A2
A1
B1
6
12
and four

8
STEP 3
A4
B2
A5
B2
19
20
Attach the two Armrests (19) to each of the Extend Arms (13) and secure them
with four M8x70 Bolts (A4) and four Washers D8 (B2).
Attach the Backrest Board (20) to the Upper Cross Brace (12) and secure it with
two M8x40 Bolts (A5) and two Washers D8 (B2).
NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled.
Assembly
13
12

9
Key NO DESCRIPTION QTY
1 LEFT/RIGHT BASE 1
2 LEFT/RIGHT BASE 1
3 SHORT FOAM GRIP 6
4 LOWER SUPPORT BAR 2
6 LOWER UPRIGHT 2
8 ROUND PLUG, 25X1.5 2
9 BOTTOM CROSS BRACE 1
10 ROUND INNER PLUG, 25x2 6
11 UPPER UPRIGHT TUBE 2
12 UPPER CROSS BRACE 1
13 EXTENDED ARM 2
14 UPPER SUPPORT BAR 2
15 MID FOAM GRIP 2
16 LONG FOAM GRIP 1
17 CONNECTIVE HEAD 2
18 PULL UP BAR 1
19 PAD, ARM 2
20 PAD, BACK 1
21 END CAP 4
2" SQUARE SLEEVE 2
PROTECTIVE COVER 2
A1 HEX BOLT, M10X20 16
A2 HEX BOLT, M10X70 14
A3 BOLT M10X55 2
A4 BOLT, M8X70 4
A5 BOLT, M8X40 2
B1 WASHER 10 14
B2 WASHER 8 6
C1 M10 Nylon Locknut 14
# BOLT PACK 1
XM-4446 Parts List
Parts List
5
7

10
Exploded View
A5
B2
B1
7
7
3
3
19
19
21
21
21
21
5
5
A2
6
A2

Customer Service: 1-800-719-4605