Marksman M3 User manual

Installation Manual Model: M3
For Technical Assistance [phone]
Step 1: Wiring Diagram
Black Wire Antenna (Do Not Ground)
Black Wire Ground to Vehicle Frame
Brown Wire Positive Output to Siren
Red Wire To Battery +12V
2-Pin White
Sensor Port
(White)
White Wire Parking Light Relay Output
Red Wire with White Stripe Parking Light Relay Input
Gray Wire (-) 200mA Channel 2 / Pager Output
Orange Wire 200mA Grounded when Armed
Yellow Wire To Ignition Switched +12V
Green Wire Negative Door Pin Switch Input
Blue Wire Instant Trigger Ground Input
Violet Wire Positive Door Pin Switch Input
Black Wire (-) Negative Door Unlock Output
Red Wire (-) Negative Door Lock Output
30
87A
87 86
85
From ignition switch To start solenoid
Cut
LED
Valet Switch
2-Pin Blue
3-Pin Black
6-Pin White
5-Pin White
Step 2: Programming
A. Programming the Transmitters
The security system has 2 transmitter programming modes. Up to 4 transmitters can be programmed.
1. “Combined” button, (Button 1 is Arm/Disarm).
2. “Dedicated” buttons, (Button 1 is Arm, Button 2 is Disarm).(Factory default setting)
To program the transmitters:
1. Turn ignition to “on” position.
2A. Push the valet switch 3 times to enter “combined button mode”.
There will be 1 long chirp and 1 short chirp of confirmation of entering combined button mode.
2B. Push the valet switch 6 times to enter “dedicated button mode”.
There will be 2 long chirps and 1 short chirp of confirmation of entering dedicated button mode.
3. Press any button on 1st transmitter, 1 short chirp to confirm code is learned.
4. Press any button on 2nd transmitter, 2 short chirps to confirm code is learned.
5. Press any button on 3rd transmitter, 3 short chirps to confirm code is learned.
6. Press any button on 4th transmitter, 4 short chirps to confirm code is learned.
7. Exit transmitter programming by turning “off” the ignition key or after 15 seconds the
security system will automatically exit transmitter programming and chirp 3 times.
Note: If more than 4 transmitters programmed, the system only keeps the last 4 transmitter codes.
B. Programming System Features (Factory preset all features to “on” position, except car-jacking)
To enter feature programming:
1. Turn the ignition “on” then “off”.
2. Within 10 seconds push the valet switch 3 times. (A long chirp).
3. Again push the valet switch 3 times. (A long chirp again to confirm in feature programming mode).
To program a feature:
4. Push the valet switch the same number of times as the feature number (see chart below).
5. Turn ignition switch from “off” to “on” to set the feature.
Example:
1. Push valet switch 2 times, (it’s on Active/Passive Arming section. The siren will chirp 2 times, LED
flash 2 times to confirm enter this feature.
2. Select Active Arming, turn ignition from “off” to “on”, 1 chirp for confirmation.
3. Select Passive Arming, turn ignition from “on” to “off”, 2 chirps for confirmation
4. If you want to program Auto Rearm (5th feature) when the system is on Active/Passive Arming,
push valet switch 3 times again. (Siren chirps 5 times, LED flashes 5 times). The system will add on
the previous valet switch pushing.
To exit feature programming:
6. During programming, if you don’t respond to previous step in 15 seconds or any time press the ARM
button on the transmitter it will exit feature programming. 3 long chirps will indicate you have exited
feature programming.
Turn ignition from “off” to “on” Turn ignition from “on” to “off”
Feature Chirp/LED Feature “on” Feature “off”
Number Confirmation (Factory Default Setting)
1 1 Chirp “on” Chirp “off”
2 2 Active Arming Passive Arming
3 3 Passive arming with door locks Passive arming without door locks
4 4 Ignition on/off with door lock/unlock
Ignition on/off without door lock/unlock
5 5 Auto Rearm “on” Auto Rearm “off”
6 6 2- Pulse Unlock “on” 2- Pulse Unlock “off”
7 7 Door Lock Time 0.9 seconds Door Lock Time 3 seconds
8 8 Car-Jacking “off” Car-Jacking “on”
9 9 Channel 2 (Trunk) Output Pager Output
© Copyright 2001
Magnadyne Corporation M3INS
Rev. B 4-17-01

Combined Button Mode
Transmitter Button Action System Function / Remark
Press and Release Arm/Lock Doors or Disarm/Unlock Doors
Press/Hold 3 Seconds Panic Function
Press Twice Arm/Lock Doors and Delete Optional Sensor
Press and Hold for Pop Trunk Release / Channel 2 Output
3 Seconds
Press Both Buttons Silent Arm / Disarm (Ignition in “Off” Position)
Press Both Buttons Activate Car-Jacking (Ignition in “On” Position)
and Hold for 1 Second
Owner’s Manual Model: M3
A. Transmitter Operation
+
or
E. Active Arming “Lock”
1. Press the “lock” button on transmitter.
2. The siren will chirp once and the parking light will flash once indicating that the system is now armed. The
vehicle’s doors will lock upon arming when interfaced with security system.
Silent Arming/Disarming: Press the “lock” and “unlock” button together on the transmitter will arm or disarm you securi-
ty system. No chirp sound will be heard, arm/disarm confirmation will be through the vehicles parking lights only.
F. Passive Arming
Active arming / disarming is controlling you security system via the remote transmitter. This security system is equipped
with an optional Passive Arming feature, which allows the security system to arm 30 seconds after the last door is closed.
Operation is as follows.
1. Turn the ignition to the “off” position and exit the vehicle.
2. After all entrances are closed the security system’s LED will flash fast for 30 seconds. If you reopen any
door/hood/trunk, the security system LED will stop flashing. It will begin flashing again once all the vehicle’s entrances
are closed.
3. After 30-second timer has elapsed, the security system will automatically “arm”. The siren will chirp one time and the
parking lights will flash one time.
Passive Door Locking: (See feature programming 3) The vehicle doors will automatically lock after passive arming cycle
has been completed.
G. Active Disarming “Unlock”
1. Press the “unlock” button on the transmitter.
2. The siren will chirp twice and parking light will flash twice indicating that the security system is now disarmed. The
vehicle doors will unlock disarming when interfaced with the security system.
Tamper Disarming: If alarm is triggered, upon disarm the system: the siren chips 4 times, parking light flash 3 times.
Automatic Re-Arm: (See feature programming 5) If this feature is selected, the security system will automatically re-arm
itself 60 seconds after disarming with remote transmitter. Automatic rearm will cancel if any door is opened before the 60
seconds timer has elapsed.
H. Valet Mode
The valet switch allows you to temporarily bypass all alarm functions, eliminating the need to hand your transmitter to
parking attendants or garage mechanics. When the system is in valet mode, all alarm function are bypassed, however the
remote panic feature and remote door locks will remain operational.
Enter Valet Mode:
1. Turn the ignition to the “on” position.
2. Push and hold valet switch for 2 seconds until the LED turns on. The LED will remain on as long as the system is in
the “valet mode”.
Exit Valet Mode:
1. Return to normal operation, turn ignition “on”.
2. Push and hold valet switch for 2 seconds, the LED will turn off to indicate the system is exiting the valet mode.
I. Panic Function
The transmitter can be used as a remote panic switch to manually trigger the alarm in case of emergency.
1. Press and hold the “lock” button on the transmitter for 3 seconds. The alarm will immediately sound.
2. To stop the alarm, press the “lock” or “unlock” button on the transmitter, the panic mode will be turned off immediately.
3. If the button is not pressed, the alarm will automatically stop after 60 seconds.
J. 60 Second Re-Arming
If you security system has become triggered, the siren will sound for 60 seconds and then stop and re-set to a fully
armed condition.
Note: If a protected entrance is left open, your security system will remain triggered for two more 60 second cycles then
full re-arm excluding the door input trigger. (Door input trigger is no longer functional) Closing the entrance will re-set
the door input trigger within 7 seconds.
K. Anti Car-Jacking
Warning: If you don’t need the car jacking function in this alarm system, be sure to set car-jacking feature “off”. This
system is default setting is car-jacking is off. (See feature programming 8)
Press and hold the “lock” and “unlock” button on the transmitter for 1 second while the vehicle’s ignition is ON will trig-
ger the car jacking. The parking lights will turn on for 1.5 seconds to indicate car jacking is activated.
1. 60 seconds after the system has been triggered, the siren starts alarming and the parking lights start flashing.
2. 90 seconds after the system has been triggered.
A. The siren will still be sounding and the parking light flashing and,
B. The starter disable will activate to prevent the vehicle from being restarted,
C. It will remain active until the vehicle’s battery power is exhausted.
Override the System to Turn Off Car-Jacking:
Turn the ignition switch from OFF to ON, and within 10 seconds push valet switch, the siren will stop and the system disarmed.
B. LED Indicator
LED is off = Alarm is disarmed.
LED is flashing slowly = Alarm is armed.
LED is flashing fast = Passive arming.
LED is on (solid) = Valet mode.
LED flashes twice then pauses = Tamper warning, alarm was triggered.
C. Chirp Indicator
One siren chirp = Security system is armed.
Two siren chirps = Security is disarmed.
Four chirps = Tamper warning, alarm was triggered.
D. Parking Light Indicator
Parking lights flash one time = Security system is armed.
Parking lights flash two times = Security is disarmed.
Parking lights flash three times = Tamper warning, alarm was triggered.
Dedicated Button Mode (Factory default setting)
Transmitter Button Action System Function / Remark
Press and Release Arm/Lock Doors
Press and Hold 3 Seconds Panic Function
Press Twice Arm/Lock Doors and Delete Optional Sensor
Press and Release Disarm/Unlock Doors
Press Button Disarm/Unlock Doors and Pop Trunk Release
and Hold for 3 Second
Press and Hold for Pop Trunk Release / Channel 2 Output
3 Seconds
Press Both Buttons Silent Arm / Disarm (Ignition in “Off” Position)
Press Both Buttons Activate Car-Jacking (Ignition in “On” Position)
and Hold for 1 Second
+
Lock Unlock
Trunk Release / 2nd Channel
Dedicated button mode shown