Mars MA-WA56-DP25N User manual

MA-WA56-DP25N
4.9-5.875 GHz Dual Polarized Antenna
MA-WA56-DP25N
MARS 5 GHz Dual Polarized Antenna designed to
provide full coverage for the 5 GHz frequency
band.
Additional Features:
-efficient and stable performance
-high gain/size ratio
-light weight and durable construction
-UV protected radome made of polycarbonate
allowing for harsh weather installations
-easy mounting allowing for Az/El adjustment
Specifications: Electrical
Frequency range 4.9 - 5.875 GHz
GAIN V-Pol:
H-Pol: 24.5 ± 1 dBi 23.5± 1 dBi
VSWR, max. 1.7 : 1
Polarization Linear, Vertical & Horizontal
3 dB Beam-Width, H-Plane, typ. 7°- 9°
3 dB Beam-Width, E-Plane, typ. 7°- 9°
Side Lobes, min. ETSI TS3, TS4, TS5
Cross Polarization, typ. - 25 dB
Port to Port Isolation,typ. - 30 dB
Front to Back Ratio, min. ETSI TS3, TS4, TS5
Input power, max 5 Watt
Input Impedance 50 Ohm
Lightning Protection DC Grounded
Mechanical
Dimensions (HxWxD) 370 x 370 x 40 mm (14.5" x14.5" x1.6")
Connector 2 x N-Type, Female
Weight 2.1 kg
Back Plane Aluminum; protected through chemical passivation
Radome UV Protected Polycarbonate
Mounting MNT-22
Environmental
Operating Temperature Range - 40 °C to + 65 °C
Vibration According to IEC 60721-3-4
Wind Load 200 Km/h (Survival)
Flammability UL94
Water Proofing IP-67
Humidity ETS 300 019-1-4,EN 302 085 (Annex A.1.1)
Salt Fog According to IEC 68-2-11
Service Life >10 years
Specifications subject to change without notice

1
1
2
2
3
3
4
4
A A
B B
C C
D D
Parts List
DESCRIPTIONQTY
ITEM
POLE 1"-4" (NOT SUPPLIED)
11
MNT-22-112
MNT-22-213
MNT-22-414
MNT-22-31
5
Helical Spring Lock Washer St. St.
#5/16
46
Plain Washer St. St. #5/16
4
7
Hex Cap Screw St. St. NC 5/16-18 x
1.25"
28
Hex Cap Screw St. St. NC 5/16-18 x 5"
29
Plain Washer St. St. #1/4
410
Helical Spring Lock Washer St. St.#1/4
211
Hex Nut St. St. NC 1/4-20
412
Hex Nut St. St. NC 5/16-18
213
1. Place item No.2 on the antenna,
as illustrated in the drawing.
Align with the screw holes.
2. Connect item No. 2 to the antenna
with spring washers (11),
flat washer (10) and nuts (12).
3. Tighten the nuts at a torque of 30 In*Lbs.
4. Connect item No. 3 to item No. 2 ONLY
as illustrated in Fig.2, with items 6,7,8,13.
Leave screw slightly loose.
5. Connect item No. 3 to item No. 5 as illustrated,
with items 6,7,8,13. Leave screw slightly loose.
6. Attach items No. 4 and 5 to the pole as illustraed,
and connect them using items No. 6,7,9.
7. Adjust the desired angle, and fully tighten the loose
screws (paragraph 4,5).
8. Tighten the nuts at a torque of 30 In*Lbs.
NOTE :
1. MOUNT MNT-22 SUITABLE FOR POLES n1"-4".
Mounting instructions - Azimuth and Elevation Adjustable Mount MNT-22
Fig .1
Fig .2
Fig .3
Fig .4
22
3
5
2
3
13 867
10 11 12
7
6813
1
4
7
6
9
Wall Mounting
Fig .5