Marshall Amplification CV350-10XB User manual

CV350-10XB/10X Operation Manual
Compact 10X Autofocus Camera (Full-HD)

2
MENU STRUCTURE
AWB
ATW
PUSH
INDOOR
OUTDOOR
MANUAL BLUE: 0~31, RED:0~31
INDOOR, OUTDOOR
AUTO
MANUAL
SHUTTER PRIORITY
IRIS PRIORITY
BRIGHT
BRIGHTNESS MANUAL, BRIGHT (0~31), 0~20
IRIS AUTO, MANUAL, 0~20
AGC LIMIT 0~20
SHUTTER AUTO, MANUAL, 1/1~30K
DSS(SENS-UP) MANUAL, OFF~1/1
FLICKERLESS OFF, ON
AUTO
MANUAL
PUSH
ZOOM SPEED 0~7
TELE LIMIT X3~X120
WIDE LIMIT X1~X9
FAR END INFINITY, 2, 3, 5, 10M
NEAR END 30CM, 1, 1.5, 2, 3, 5, 10M
LENS INITIAL OFF, AUTO, ONE PUSH
USER PRESET
WDR
BLC
SPOT
ACE GAIN
LEVEL
COLOR
WB
CONTROL
AE
CONTROL
(EXPOSURE)
FOCUS
CONTROL
FOCUS MODE
BACK LIGHT
WDR/BLC
ECLIPSE
Mode

MENU STRUCTURE
D/N LEVEL
MARGIN
DWELL TIME
NIGHT BURST
DAY
NIGHT NIGHT BURST
D/N LEVEL
DWELL TIME
NIGHT BURST
COLOR LEVEL 0~20
SHARPNESS 0~20
IMAGE FLIP
DEFOG AUTO, MANUAL
3D-DNR OFF, LOW, MIDDLE, HIGH
MOTION
SHADING
GAMMA
RESOLUTION
USER TITLE
ZOOM MAGNIFICATION
PRIVACY
ADDRESS 01~255
ADDRESS DISPLAY OFF, ON
BAUDRATE
LANGUAGE
DEFECT ADJ
VER.
RESET
EXIT
IMAGE
CONTROL
AUTO
EXT
DISPLAY
CONTROL
3

Zoom/Focus & OSD Button
MAIN MENU
WB CONTROL
AE CONTROL
FOCUS CONTROL
BACK LIGHT
IMAGE CONTROL
DISPLAY CONTROL
RESET
EXIT
Press SET button to access the MAIN MENU.
Use the UP & DOWN buttons
to select the desired item.
Use the LEFT & RIGHT buttons
to change the sub-item.
Icon indicates “Press OSD Button” or “Enter Sub Menu”.
ATW
INDOOR
SAVE
MENU On, One Push AF Key
Menu On: Press and hold menu key for 2 seconds to display menu.
Menu Mode: To select data or exit from menu, press menu key.
One Push AF: To adjust focus position, press and release menu key when One Push AF mode is enabled.
Focus NEAR: Press and hold right key for continuous optical focus near.
MENU: To change menu parameter, press right key while menu is displayed.
Focus Far: Press and hold left key for continuous optical focus far.
MENU: To change menu parameter, press left key while menu is displayed.
Zoom TELE: Press and hold up key for continuous optical zoom in (Tele).
MENU: To move up menu item, press up key while menu is displayed.
Zoom WIDE: Press and hold down key for continuous optical zoom out (Wide).
MENU: To move down menu item, press down key while menu is displayed.
4

Select WB CONTROL using the UP or DOWN button.
You can change between AWB, ATW, PUSH, INDOOR, OUTDOOR, and MANUAL using
the LEFT or RIGHT button.
AWB: Controls the automatic adjustment of the light source's color
temperature to 3,000°K ~ 8,000°K.
WB CONTROL AWB, ATW, PUSH,
INDOOR, OUTDOOR, MANUAL
ATW: Continuously adjusts camera color balance in accordance with any
change in color temperature. Compensates for color temperature changes
within the range of 1,900°K to 11,000°K.
INDOOR: Select this when the color temperature is between 4,500 ° K and 8,500 ° K.
PUSH: Color temperature will be manually adjusted by pushing the OSD
button. Place the white paper in front of the camera when OSD button is
pressed to obtain the optimum result.
MANUAL: Select this to fine-tune White Balance manually.
OUTDOOR: Select this when the color temperature is between 1,700°K and
11,000°K (Ex. Sodium light inclusion)
MAIN MENU
WB CONTROL
AE CONTROL
FOCUS CONTROL
BACK LIGHT
IMAGE CONTROL
DISPLAY CONTROL
RESET
EXIT
ATW
INDOOR
SAVE
You can adjust the blue and red tone level manually.
BLUE: Adjust the blue tone of the image. (0~31)
RED: Adjust the red tone of the image. (0~31)
WB CONTROL
BLUE IIIIIIIIIIIII31
RED IIIIIIIIIIIII31
RETURN
■ Set White Balance first by using the ATW or AWB mode. After that switch to MANUAL mode,
■ White Balance may not work properly under the following conditions. In this case, select the AWC mode.
- When the ambient illumination of the subject is dim.
- If the camera is directed towards a fluorescent light or is installed in place where illumination changes
dramatically, the White Balance operation may become unstable.
5

Select AE CONTROL using the UP or DOWN button.
You can change between INDOOR and OUTDOOR using the LEFT or RIGHT button.
AE CONTROL INDOOR, OUTDOOR
INDOOR: Select this when the camera is installed indoor.
OUTDOOR: Select this when the camera is installed outdoor.
MAIN MENU
WB CONTROL
AE CONTROL
FOCUS CONTROL
BACK LIGHT
IMAGE CONTROL
DISPLAY CONTROL
RESET
EXIT
ATW
INDOOR
SAVE
You can select one sub-mode from AUTO, MANUAL, SHUTTER PRIORITY, IRIS PRIORITY,
and BRIGHT. using the LEFT or RIGHT button.
AE CONTROL
MODE AUTO
BRIGHTNESS IIIIIIIIIIIII 10
IRIS AUTO
AGC LIMIT IIIIIIIIIIIII 13
SHUTTER AUTO
DSS OFF
FLICKERLESS OFF
RETURN
You can select one sub-mode from AUTO, MANUAL, SHUTTER PRIORITY, IRIS PRIORITY,
and BRIGHT. using the LEFT or RIGHT button.
You can change the AE CONTROL mode between AUTO, MANUAL, IRIS PRIORITY,
SHUTTER PRIOROTY, and BRIGHT using the LEFT or RIGHT button.
AUTO: IRIS and SHUTTER are controlled automatically.
MANUAL: IRIS, GAIN, and SHUTTER are controlled manually.
IRIS PRIORITY: Manual IRIS and GAIN control with automatic SHUTTER control.
SHUTTER PRIORITY: Manual SHUTTER and GAIN control with automatic
IRIS control.
BRIGHT: IRIS and GAIN can be controlled by control of BRIGHTNESS.
6

You can change the AE CONTROL mode between AUTO, MANUAL, IRIS PRIORITY,
SHUTTER PRIOROTY, and BRIGHT using the LEFT or RIGHT button.
Select a menu from BRIGHTNESS, IRIS, AGC GAIN LIMIT, SHUTTER, DSS, and
FLICKERLESS using the UP or DOWN button.
BRIGHTNESS
AE CONTROL BRIGHTNESS, IRIS, AGC LIMIT,
SHUTTER, DSS, FLICKERNESS
IRIS
SHUTTER: Adjust the SHUTTER speed.
AGC LIMIT
DSS (SENS-UP)
MAIN MENU
WB CONTROL
AE CONTROL
FOCUS CONTROL
BACK LIGHT
IMAGE CONTROL
DISPLAY CONTROL
RESET
EXIT
ATW
INDOOR
SAVE
AE CONTROL
MODE AUTO
BRIGHTNESS IIIIIIIIIIIII 10
IRIS AUTO
AGC LIMIT IIIIIIIIIIIII 13
SHUTTER AUTO
DSS OFF
FLICKERLESS OFF
RETURN
FLICKERLESS: Use this function when you experience picture flicker,
this happens when there is a conflict with the installed lighting frequency.
0~31: Adjust the screen brightness.
MANUAL: BRIGHTNESS control is fixed, and give the AE control
priority to others.
AUTO: IRIS controls exposure automatically but SHUTTER is fixed.
1~17: Adjust the screen brightness.
MANUAL: IRIS control is fixed, and give the AE control priority to others.
0~20: Adjust the gain level.
AUTO: Shutter controls exposure automatically when iris is set to manual.
1/2~30K: Set the shutter speed from 1/1, 2, 4, 8, 15, 30, 60, 90, 100, 125,
180, 250, 350, 500, 725, 1000, 1500, 2K, 3K, 4K, 6K, 10K, 20K, and 30K.
MANUAL: Shutter is fixed, and give the AE control priority to others.
OFF~1/2: Set the DSS level from OFF, 1/30, 1/15, 1/8, 1/4, and 1/1.
MANUAL: DSS is fixed, and give the AE control priority to others.
7

Select FOCUS CONTROL using the UP or DOWN button.
You can select FOCUS MODE from AUTO, MANUAL and PUSH using the LEFT or RIGHT button.
FOCUS CONTROL AUTO, MANUAL, PUSH
AUTO: Automatically adjusts the focus position.
MANUAL: Manually adjusts the focus position when zoom is changed.
MAIN MENU
WB CONTROL
AE CONTROL
FOCUS CONTROL
BACK LIGHT
IMAGE CONTROL
DISPLAY CONTROL
RESET
EXIT
ATW
INDOOR
SAVE
FOCUS CONTROL
FOCUS MODE AUTO
ZOOM SPEED 04
TELE LIMIT X5
WIDE LIMIT X1
FAR END INFINITY
NEAR END 1M
LENS INITIAL OFF
USER PRESET OFF
RETURN
PUSH: When this mode is enabled, it will automatically adjusts the focus position
only when the zoom is changed.
8

Select FOCUS CONTROL using the UP or DOWN button.
You can select ZOOM SPEED, TELE LIMIT, WIDE LIMIT, FAR END, NEAR END, LENS INITIAL
and USER PRESET using the LEFT or RIGHT button.
FOCUS CONTROL
ZOOM SPEED: Set the zoom speed from 00~07.
TELE LIMIT: Set the limit of the tele control from X3, X4, X5, X6, X7, X8, X9,
X10, X20, X30, X40, X50, X60, X70, X80, X90, X100, X110, and X120.
MAIN MENU
WB CONTROL
AE CONTROL
FOCUS CONTROL
BACK LIGHT
IMAGE CONTROL
DISPLAY CONTROL
RESET
EXIT
ATW
INDOOR
SAVE
FOCUS CONTROL
FOCUS MODE AUTO
ZOOM SPEED 04
TELE LIMIT X5
WIDE LIMIT X1
FAR END INFINITY
NEAR END 1M
LENS INITIAL OFF
USER PRESET OFF
RETURN
WIDE LIMIT: Set the limit of the zoom control from X1, X2, X3, X4, X5, X6, X7, X8, and X9.
00 is the slowest zoom speed set value. 07 is the fastest zoom speed set value.
FAR END: Set the limit for the far focusing from INFINITY, 2, 3, 5, and 10M.
The lens moves to adjust the focus from the distance.
NEAR END: Set the priority distance limit for near focusing from 30CM, 1, 1.5,
2, 3, 5, and 10M.
LENS INITIAL: This function repeats adjustment of the focus level at the interval.
USER PRESET: This function is used to set user defined zoom and focus position.
Up to 32 preset position can be set.
ONE PUSH: The focus setting is initialized when ONE PUSH is selected.
AUTO: The focus is initialized as DAY setting.
DAY:
Select the interval DAY/DAYS from 01~07 using the LEFT or RIGHT button.
USER PRESET: Select the preset ID from 00~31 using the LEFT or RIGHT button.
ACTIVE: Activate the focus preset setting of the USER PRESET.
SAVE:
Save the preset setting.
RESET: Reset the preset setting.
9

Select BACK LIGHT using the UP or DOWN button.
You can select WDR/BLC, ACE, and ECLIPSE using the LEFT or RIGHT button.
BACK LIGHT WDR/BLC
WDR/BLC
MAIN MENU
WB CONTROL
AE CONTROL
FOCUS CONTROL
BACK LIGHT
IMAGE CONTROL
DISPLAY CONTROL
RESET
EXIT
ATW
INDOOR
SAVE
BACK LIGHT
WDR/BLC WDR
ACE OFF
ECLIPSE OFF
RETURN
WDR: Enable user to view both object and background more clearly when
background is too bright.
WDR-LEVEL:
Select the WDR level from 01~04 using the LEFT or RIGHT button.
BLC: Enable a back light compensation feature.
SPOT: Enables a user to select a desired area on a picture and view that
area more clearly when background is too bright.
WIDTH: Change the width of SPOT area using the LEFT or RIGHT button.
HEIGHT: Change the height of SPOT area using the UP or DOWN button.
MOVE HOR:
Move the SPOT area horizontally using the LEFT or RIGHT button.
MOVE VER:
Move the SPOT area vertically using the UP or DOWN button.
SPOT
WIDTH IIIIIIIIIIIIIIIIII 06
HEIGHT IIIIIIIIIIIIIIIIII 08
MOVE HOR IIIIIIIIIIIIIIIIII 02
MOVE VER IIIIIIIIIIIIIIIIII 05
RETURN
10

Select BACK LIGHT using the UP or DOWN button.
You can select WDR/BLC, ACE, and ECLIPSE using the LEFT or RIGHT button.
BACK LIGHT WDR/BLC
ACE (D-WDR) :Brightness correction of the dark image area.
MAIN MENU
WB CONTROL
AE CONTROL
FOCUS CONTROL
BACK LIGHT
IMAGE CONTROL
DISPLAY CONTROL
RESET
EXIT
ATW
INDOOR
SAVE
BACK LIGHT
WDR/BLC WDR
ACE OFF
ECLIPSE ON
RETURN
GAIN: Select the GAIN level from LOW, MIDDLE, and HIGH using the LEFT or RIGHT
button.
ECLIPSE
LEVEL IIIIIIIIIIIIIIIIII 20
COLOR GRN
RETURN
ECLIPSE :Highlight the bright area with a masking box with a selected color.
LEVEL:
Select the masking level from 0~20 using the LEFT or RIGHT button.
COLOR: Select the color of masking from GRN, MAG, RED, BLUE, BLK, WHT, YEL,
and CYN using the LEFT or RIGHT button.
11

Select IMAGE CONTROL using the UP or DOWN button.
You can select DAY/NIGHT using the UP or DOWN button.
IMAGE CONTROL DAY/NIGHT
DAY/NIGHT
MAIN MENU
WB CONTROL
AE CONTROL
FOCUS CONTROL
BACK LIGHT
IMAGE CONTROL
DISPLAY CONTROL
RESET
EXIT
ATW
INDOOR
SAVE
IMAGE CONTROL
DAY/NIGHT AUTO
COLOR IIIIIIIIIIIIIIIII 10
SHARPNESS IIIIIIIIIIIIIIIII 10
IMAGE FLIP OFF
DEFOG OFF
3D-DNR LOW
MOTION OFF
SHADING OFF
GAMMA STANDARD
RESOLUTION HD1080i60/NTSC
RETURN
Select the DAY/NIGHT mode of the camera from AUTO, DAY, NIGHT, and EXT using the
LEFT or RIGHT button.
AUTO: The camera will stay in DAY in a normal environment, but switched
to NIGHT mode when ambient illumination become this pre-set level.
D/N LEVEL: This level is threshold for switching day to night. It is same
as the exposure gain level.
MARGIN: Set the margin between Day →Night switching level and Night →Day
switching level. Different exposure gain level is needed to avoid malfunctions.
DWELL TIME: Select the checking time of light condition to confirm to change from
the day mode to the night mode.
NIGHT BURST: Night burst OFF makes that the color burst is removed when ICR
switches to black/white.
AUTO
D/N LEVEL IIIIIIIIIIIIIIIIII 20
MARGIN IIIIIIIIIIIIIIIIII 20
DWELL TIME 01
NIGHT BURST ON
COLOR
12

Select IMAGE CONTROL using the UP or DOWN button.
You can select DAY/NIGHT using the UP or DOWN button.
IMAGE CONTROL DAY/NIGHT
DAY/NIGHT
IMAGE CONTROL
DAY/NIGHT EXT
COLOR IIIIIIIIIIIIIIIII 10
SHARPNESS IIIIIIIIIIIIIIIII 10
IMAGE FLIP OFF
DEFOG OFF
3D-DNR LOW
MOTION OFF
SHADING OFF
GAMMA STANDARD
RESOLUTION HD1080i60/NTSC
RETURN
Select the DAY/NIGHT mode of the camera from AUTO, DAY, NIGHT, and EXT using the
LEFT or RIGHT button.
DAY: The picture is always displayed in color.
NIGHT BURST: Night burst OFF makes that the color burst is removed when ICR
switches to black/white
DWELL TIME: Select the checking time of light condition to confirm to change from
the day mode to the night mode.
NIGHT BURST: Night burst OFF makes that the color burst is removed when ICR
switches to black/white.
DAY / NIGHT
D/N LEVEL LOW
DWELL TIME 01
NIGHT BURST ON
COLOR
NIGHT: The picture is always displayed in black/white.
EXT: Control the image modes of color and B/W when an external controller
is synchronized via the EXT D/N port.
D/N LEVEL: This level is threshold for switching day to night. It is same
as the exposure gain level.
13

Select IMAGE CONTROL using the UP or DOWN button.
You can select COLOR LEVEL, SHARPNESS, IMAGE FLIP, and DEFOG using the UP or
DOWN button.
IMAGE CONTROL COLOR LEVEL, SHARPNESS
IMAGE FLIP, DEFOG
COLOR LEVEL : Adjust the color level value for a fine color tune.
IMAGE CONTROL
DAY/NIGHT EXT
COLOR IIIIIIIIIIIIIIIII 10
SHARPNESS IIIIIIIIIIIIIIIII 10
IMAGE FLIP OFF
DEFOG OFF
3D-DNR LOW
MOTION OFF
SHADING OFF
GAMMA STANDARD
RESOLUTION HD1080i60/NTSC
RETURN
DEFOG
MODE AUTO
GAIN MIDDLE
RETURN
Adjust the color level from 00~20 using the LEFT or RIGHT button.
SHARPNESS : Increasing this value, the picture outline becomes stronger and clearer.
Adjust the sharpness level from 00~20 using the LEFT or RIGHT button.
IMAGE FLIP : Video output will be flipped.
Select the image flip mode from MIRROR-HORIZONTALLY, FLIP-VERTICALLY, or ROTATION
using the LEFT or RIGHT button.
DEFOG : This feature will help increase visibility in extreme weather conditions, such
as fog, rain or in a very strong luminous intensity.
Select the DEFOG mode from AUTO or MANUAL using the LEFT or RIGHT button.
IMAGE CONTROL
DAY/NIGHT EXT
COLOR IIIIIIIIIIIIIIIII 10
SHARPNESS IIIIIIIIIIIIIIIII 10
IMAGE FLIP OFF
DEFOG OFF
3D-DNR LOW
MOTION OFF
SHADING OFF
GAMMA STANDARD
RESOLUTION HD1080i60/NTSC
RETURN
IMAGE CONTROL
DAY/NIGHT EXT
COLOR IIIIIIIIIIIIIIIII 10
SHARPNESS IIIIIIIIIIIIIIIII 10
IMAGE FLIP MIRROR-HOR
DEFOG OFF
3D-DNR LOW
MOTION OFF
SHADING OFF
GAMMA STANDARD
RESOLUTION HD1080i60/NTSC
RETURN
14

Select IMAGE CONTROL using the UP or DOWN button.
You can select 3D-DNR, MOTION, SHADING, and GAMMA using the UP or DOWN button.
IMAGE CONTROL 3D-DNR, MOTION
SHADING, GAMMA
3D-DNR : This feature will reduce the video noise caused by movement at
low ambient light.
IMAGE CONTROL
DAY/NIGHT EXT
COLOR IIIIIIIIIIIIIIIII 10
SHARPNESS IIIIIIIIIIIIIIIII 10
IMAGE FLIP OFF
DEFOG OFF
3D-DNR LOW
MOTION OFF
SHADING OFF
GAMMA STANDARD
RESOLUTION HD1080i60/NTSC
RETURN
MOTION
DET. SIZE IIIIIIIIIIIIIII 03
SENSITIVITY IIIIIIIIIIIIIII 10
MASK ACTIVE ON
WIDTH IIIIIIIIIIIIIII 26
HEIGHT IIIIIIIIIIIIIII 33
MOVE HOR IIIIIIIIIIIIIII 01
MOVE VER IIIIIIIIIIIIIII 01
RETURN
Select the 3D-DNR level from OFF, LOW, MIDDLE, and HIGH using the LEFT or RIGHT button.
MOTION : This feature will observe the object movement by motion zone and sensit-
ivity that are pre-set with sub menu. The motion detection signal can be relayed out
with MD OUT port.
DET. SIZE: Select the size of the object that is motion detected from 00 ~ 04.
SENSITIVITY: Select the motion detection size from 00 ~ 20.
MASK ACTIVE:
Enable/disable the motion detection mask display.
WIDTH: Change the width of motion detection mask using the LEFT or RIGHT button.
HEIGHT:
Change the height of motion detection mask using the UP or DOWN button.
MOVE HOR:
Move the motion detection mask area horizontally using the LEFT or
RIGHT button.
MOVE VER:
Move the motion detection mask area vertically using the UP or DOWN
button.
SHADING : This feature will correct the inconsistent brightness level in the image.
GAMMA : This feature will adjust video output brightness.
Select the GAMMA level from STANDARD, STRAIGHT, LOW, MIDDLE, and HIGH using the LEFT
or RIGHT button.
15

Select IMAGE CONTROL using the UP or DOWN button.
You can select RESOLUTION using the UP or DOWN button.
IMAGE CONTROL RESOLUTION
RESOLUTION : Change video output specification.
Select the RESOLUTION using the LEFT or RIGHT button.
MAIN MENU
WB CONTROL
AE CONTROL
FOCUS CONTROL
BACK LIGHT
IMAGE CONTROL
DISPLAY CONTROL
RESET
EXIT
ATW
INDOOR
SAVE
IMAGE CONTROL
DAY/NIGHT AUTO
COLOR IIIIIIIIIIIIIIIII 10
SHARPNESS IIIIIIIIIIIIIIIII 10
IMAGE FLIP OFF
DEFOG OFF
3D-DNR LOW
MOTION OFF
SHADING OFF
GAMMA STANDARD
RESOLUTION HD1080i60/NTSC
RETURN
CV350-10XB Model
CV350-10X Model
Select the RESOLUTION from 1080P25/30, 1080i50/60, 720P50/60, and 1080P50/60
using the LEFT or RIGHT button.
Select the RESOLUTION from 1080P29.97, 1080i59.94, 1080P59.94, 720P59.94 using
the LEFT or RIGHT button.
16

Select DISPLAY CONTROL using the UP or DOWN button.
You can select USER TITLE, ZOOM MAGNIFICATION, PRIVACY, ADDRESS, ADDRESSS
DISPLAY, BAUDRATE, LANGUAGE, DEFECT ADJ, and VER. using the UP or DOWN button.
DISPLAY CONTROL USER TITLE, ZOOM MAG
USER TITLE : The camera title can be entered and it will appear over the video output.
MAIN MENU
WB CONTROL
AE CONTROL
FOCUS CONTROL
BACK LIGHT
IMAGE CONTROL
DISPLAY CONTROL
RESET
EXIT
ATW
INDOOR
SAVE
DISPLAY CONTROL
USER TITLE ON
ZOOM MAG OFF
PRIVACY OFF
ADRESS 01
ADR DISPLAY OFF
BAUDRATE 9600
LANGUAGE
DEFECT ADJ OFF
VER. H.5.0.2-8
RETURN
You can input the camera title from the virtual keyboard using the LEFT, RIGHT, UP, DOWN, and
SET button.
USER TITLE
A B C D E F G H I J K L M
N O P Q R S T U V W X Y Z
a b c d e f g h i j k l m
n o p q r s t u v w x y z
! @ # $ % ^ & * ( ) ? .
0 1 2 3 4 5 6 7 8 9
CLEAR RESET RETURN
ZOOM MAGNIFICATION : Turn On or off of the zoom scale display from X01~X10.
X10
DISPLAY CONTROL
USER TITLE ON
ZOOM MAG ON
PRIVACY OFF
ADRESS 01
ADR DISPLAY OFF
BAUDRATE 9600
LANGUAGE
DEFECT ADJ OFF
VER. H.5.0.2-8
RETURN
17

Select DISPLAY CONTROL using the UP or DOWN button.
You can select PRIVACY using the UP or DOWN button.
DISPLAY CONTROL PRIVACY
PRIVACY : Mask an area you want to hide on the screen.
MAIN MENU
WB CONTROL
AE CONTROL
FOCUS CONTROL
BACK LIGHT
IMAGE CONTROL
DISPLAY CONTROL
RESET
EXIT
ATW
INDOOR
SAVE
DISPLAY CONTROL
USER TITLE ON
ZOOM MAG OFF
PRIVACY ON
ADRESS 01
ADR DISPLAY OFF
BAUDRATE 9600
LANGUAGE
DEFECT ADJ OFF
VER. H.5.0.2-8
RETURN
PRIVACY
MASK NO 01
MASK ACTIVE ON
MASK COLOR BLK
WIDTH IIIIIIIIIIIIIIIIIII 05
HEIGHT IIIIIIIIIIIIIIIIIII 05
MOVE HOT IIIIIIIIIIIIIIIIIII 10
MOVE VER IIIIIIIIIIIIIIIIIII 06
TRANS 00
RESET MASK
RESET ALL
RETURN
MASK NO: Select the mask number to modify using the LEFT or RIGHT button.
MASK ACTIVE: Enable/Disable the mask display using the LEFT or RIGHT button.
MASK COLOR: Select the mask color using the LEFT or RIGHT button.
WIDTH: Change the width of SPOT area using the LEFT or RIGHT button.
HEIGHT: Change the height of SPOT area using the UP or DOWN button.
MOVE HOR:
Move the SPOT area horizontally using the LEFT or RIGHT button.
MOVE VER:
Move the SPOT area vertically using the UP or DOWN button.
TRANS:
Select the mask transparency using the LEFT or RIGHT button.
RESET MASK: Reset the setting values of the selected MASK NO.
RESET ALL:
Reset the setting values of the all MASK.
18

Select DISPLAY CONTROL using the UP or DOWN button.
You can select ADDRESS, ADD DISPLAY, BAUDRATE, LANGUAGE, DEFECT ADJ, and VER.
using the UP or DOWN button.
DISPLAY CONTROL ADDRESS, BAUDRATE
LANGUAGE, DEFECT
ADDRESS : Select the camera ID number from 01~255.
MAIN MENU
WB CONTROL
AE CONTROL
FOCUS CONTROL
BACK LIGHT
IMAGE CONTROL
DISPLAY CONTROL
RESET
EXIT
ATW
INDOOR
SAVE
DISPLAY CONTROL
USER TITLE ON
ZOOM MAG OFF
PRIVACY ON
ADRESS 01
ADR DISPLAY OFF
BAUDRATE 9600
LANGUAGE
DEFECT ADJ OFF
VER. H.5.0.2-8
RETURN
DEFECT_DET
THRS_ _ _ _ 0 0 0 0 0 0 0 0 0 1 1
CTN _ _ _ _ 0 0 0 0 0 0 0 0 0 8 9
L, R key to ADJ
ENT to finish
ADD DISPLAY : Enable/Disable the display of the camera address ID.
BAUDRATE : Set the baudrate of RS-485 communication (2400, 4800, 9600, 19200,
38400, 57600, 115200).
LANGUAGE : You can select the menu language according to your requirements.
Select the OSD language from ENGLISH, 简体, FRANÇAIS, DEUTSCH, ESPAÑOL,
PORTUGUÊS, and РУССКИЙT using the LEFT or RIGHT button.
DEFECT ADJ.: Defective pixels can be corrected.
VER.: Display the firmware version of the camera.
19

Select RESET using the UP or DOWN button.
RESET RESET
RESET : Reset the camera settings to the factory defaults.
MAIN MENU
WB CONTROL
AE CONTROL
FOCUS CONTROL
BACK LIGHT
IMAGE CONTROL
DISPLAY CONTROL
RESET
EXIT
ATW
INDOOR
SAVE
20