Marshall Amplification CV605-BK User manual

Broadcast A/V Division
User Manual
CV605-BK (black)
CV605-WH (white)
5x HD60 IP PTZ Camera with 3GSDI
User Manual
CV605-BK (Black)
CV605-WH (White)
5x HD60 IP PTZ Camera with 3GSDI

CV605-BK/WH Manual
www.marshall-usa.com2 3
Content
PLEASE NOTE ................................................................... ERROR! BOOKMARK NOT DEFINED.
1. FAST INSTALLATION ...................................................................................................................... 5
1.2 POWER ON INITIAL CONFIGURATION ........................................................................................................5
1.3 VIDEO OUTPUT ...................................................................................................................................5
2. PRODUCT OVERVIEW ................................................................................................................... 6
2.1 PRODUCT INTRODUCTION......................................................................................................................6
2.1.1 Dimension................................................................................................................................6
2.1.2 Accessory.................................................................................................................................6
2.2 MAIN FEATURES ..................................................................................................................................7
2.3 TECHNICAL SPECIFICATION .....................................................................................................................7
2.4 INTERFACE INSTRUCTION .......................................................................................................................8
2.4.1 External Interface ....................................................................................................................8
3. APPLICATION INSTRUCTION......................................................................................................... 9
3.1 REMOTE CONTROLLER ........................................................................................................................10
3.1.1 SETTING EXPLANATION......................................................................................................... 10
3.1.2 Applications...........................................................................................................................10
3.2 MENU SETTING .............................................................................................................................12
3.2.1 Main Menu ............................................................................................................................12
3.2.2 System Setting .......................................................................................................................13
3.2.3 Camera Setting......................................................................................................................13
3.2.4 P/T/Z ......................................................................................................................................16
3.2.5 Video Format .........................................................................................................................17
3.2.6 Network settings ...................................................................................................................17
3.2.7 Audio settings........................................................................................................................18
3.2.8 Version...................................................................................................................................18
3.2.9 Restore Default......................................................................................................................19
4. NETWORK CONNECTION............................................................................................................ 19
4.1 CONNECTING MODE ..........................................................................................................................19
4.2 IE LOG IN.........................................................................................................................................21
4.2.1 Web client..............................................................................................................................21
2)Download/Install Plug in .............................................................................................................21
4.2.2 Preview ..................................................................................................................................21
4.2.4 Configuration.........................................................................................................................21
1) Audio Configuration ...................................................................................................................22
2) Video configuration....................................................................................................................22
4.2.6 Network Configure ................................................................................................................24
4.2.7 System Configure...................................................................................................................24
4.2.8 Logout....................................................................................................................................25
5. SERIAL COMMUNICATION CONTROL......................................................................................... 25
5.1VISCA PROTOCOL LIST ........................................................................................................................26
5.1.1 Command list.........................................................................................................................26
5.1.2 Inquiry command...................................................................................................................27
5.2 PELCO-D PROTOCOL COMMAND LIST .....................................................................................................28
5.3 PELCO-P PROTOCOL COMMAND LIST......................................................................................................28
6. CAMERA MAINTENANCE AND TROUBLESHOOTING ................................................................. 29
6.1 CAMERA MAINTENANCE .....................................................................................................................29
6.2 TROUBLESHOOTING............................................................................................................................29

CV605-BK/WH Manual
www.marshall-usa.com4 5
1. Fast Installation
1.1 Camera Layout Explanation
Figure 1.1 Interface of SDI Model
Interface of SDI Model
：
1. Camera Lens 2. Power Indicator
3. Remote Control Receiver Light 4. Position Lock
5. 1/4”-20 Mounting Hole
6. Audio Input (TRS)
7. 3GSDI (BNC)
8. Ethernet (IP) Port
9. RS232 (RJ45) Port
10. DC12V Input Power Supply Socket
1.2 Power-ON initial setup
1) Power ON: Connect the DC12V power supply included in box to power outlet and camera power input.
2) Initial configuration: Once powered up the power indicator light will start blinking, camera head will move from bottom
left to the bottom, and then moves to the HOME position (horizontal and vertical center), while the camera module boots
up. As soon as remote-control receiver light stops blinking, the self-check and boot up is complete.
Note:
1. The default address of the remote controller is the 1# address.
2. If you SET preset to “0” then after self-check and boot up is complete, the camera will then automatically move to the
preset 0 position.
1.3 Video Output
1) Network output:
a. Network Cable Connection Port: No.8 in Figure1.1
Please Note
This manual details features, functions, installation, operation and recommendation. Please
read this manual completely before installation and use.
Description of use
1. In order to prevent damage to this camera or other components within the workflow,
please use it within its prescribed purpose and scope of operation.
2. Keep the device away from rain, moisture, or heavy humidity.
3. To prevent electric shock or damage to internal components, do not open the main case;
only qualified technicians should conduct repairs.
4. Do not use the device beyond scope of its temperature, humidity or power supply
specification.
5. When cleaning the camera lens, use a soft dry cloth. If dirt is harder to remove please
use water or mild soap. Do not use strong or corrosive detergent, it may scratch the
lens and/or cause chemical residue to remain.
Careful handing
6. Avoid damage from heavy pressure, strong vibration or immersion during
transportation, storage and installation.
Power supply polarity
7. This product uses DC 12V power supply (higher or lower voltage may cause damage)
Install with caution
8. Do not carry the camera by the camera head or rotate it with force, otherwise it may
cause mechanical malfunction and damage internal belts and gears.
9. This product should be placed on a stable desktop or other horizontal surfaces. Do not
install the product on anything other than a level position, otherwise it may display
inclined or off axis image.
10. This product shell is made of organic materials. Do not expose it to any liquid, gas or
solids which may corrode the shell.
11. During installation, ensure that there are no obstacles within rotation range of the head
to limit it’s movement (Pan/Tilt).
12. Do not power on before installation is complete, as it may be restricted in movement.
Do not disassemble the product without permission from manufacturer.
13. This product contains no parts which can be repaired in field or at site. Any damage
arising from disassembly voids the product warranty
Magnetic field interference
14. Magnetic fields within a specific frequency may affect camera video images; this is a
Class A product. Some applications within a household environment may cause radio
interference. Make sure there are no other radio interreference present.

CV605-BK/WH Manual
www.marshall-usa.com6 7
b. Webpage Login: Open web browser and enter default IP address 192.168.5.163 in the address bar (factory default);
press Enter and enter the LOGIN prompt. Then enter the default user name admin and password admin (factory
default); then press Enter to see preview page, users can carry out PTZ control, playback, configuration and other
operations from this software GUI.
2) 3GSDI (BNC) output: Connect the camera to a monitor or switching equipment using 3GSDI (RG6) coaxial cable, then the
monitor or other equipment will display image.
2. Product overview
2.1 Product Introduction
2.1.1 Dimension
Figure 2.2 Camera dimension
2.1.2 Accessory
During unpacking the box, please check that all the supplied accessories are included:
Model NO. Accessories
CV605-BK/
CV605-WH
Power adapter
IR Remote controller
Thank You Card
Warranty card
2.2 Main Features
The CV605 camera series offers high quality performance with rich feature sets. The features include advanced ISP
processing algorithms to provide vivid images with deep color depth, crisp and clear HD images and accurate color
reproduction. The CV605 also supports H.265/H.264 encoding which creates smooth IP video performance and clear
images under less-than-ideal bandwidth conditions.
1. True High-Definition Image: 1/2.8-inch-high quality CMOS sensor. Resolution is up to 1920x1080p up to 60 fps.
2. Optical Zoom Lens: 5X zoom lens reaches a wide angle 85° AOV with very low distortion
3. Leading Auto Focus Technology: Cutting edge auto focus algorithm makes lens a fast, accurate and stable auto-focus.
4. Low Noise and High SNR: Low Noise CMOS effectively ensure high SNR of camera video.
Advanced 2D/3D noise reduction technology is also used to further reduce the noise, while ensuring image sharpness.
5. Quiet PTZ: By designing in a high accuracy step motor technology, camera movement is extremely quiet with smooth
maneuvers and fast accurate destinations (presets).
6. Video Outputs: Support up to 3GSDI and LAN interfaces.
7. Multiple Video compression: Support H.265/H.264 video compression
8. Audio Input Interface: Supports 16000,32000,44100,48000 sampling frequency and AAC, MP3, G.711A audio coding.
9. Multiple Network Protocol Support: ONVIF, RTSP, RTMP protocols
10. Low-power sleep function: Supports ultra-low power consumption while in sleep mode (less then 400mW)
11.Multiple Control Protocols: Support VISCA, Pelco-D, Pelco-P and supports auto-recognize protocol discovery.
12.255 Presets Positions: Up to 255 presets (10 presets available on IR remote controller).
2.3 Technical specification
Model
CV605-BK / CV605-WH
Camera Specs
Optical Zoom
5X Optical Zoom (3
～
15.5mm)
Sensor
1/2.8-inch-high quality HD CMOS sensor
Effective Pixels
Video Format
16:9, 2 Megapixel
3G/HD-SDI video formats
1920x1080p @ 60/59.94/50/30/29.97/25 fps
1920x1080i @ 60/59.94/50 fps
1280x720p @ 60/59.94/50/30/29.97/25 fps
Viewing Angle
85° (wide open) through 16° (telephoto)
Digital Zoom
10X additional
Minimum Illumination
0.5Lux (F1.8, AGC ON)
DNR
2D & 3D DNR
White Balance
Auto / Manual/ One Push/ VAR
Focus
Auto/Manual/One Push
Iris
Close/F11/9.6/8.0/6.8/5.6/4.8/4.0/3.4/2.8/2.4/2.0/1.8
Electronic Shutter
Auto/Manual
BLC
ON/OFF
Video Adjustment
Brightness, Color, Saturation, Contrast, Sharpness,
B/W mode, Gamma curve
SNR
>55dB
Input/ Output Interface
Oponal Accessories (sold separately):
• CV605-WM (Wall Mount-Black)
• CV605-WMW (Wall Mount-White)
• CV605-CM Ceiling Mount

CV605-BK/WH Manual
www.marshall-usa.com8 9
Available Video I/O 3G/HD-SDI, LAN, RS232 (RJ45), Audio-IN
Image Output Multiple
Code Source
Dual Code Source output (3GSDI, LAN)
Video Compression Format
H.264 & H.265
Audio Input Interface
Two-channel 3.5mm (Line or Mic level)
Audio Output
3G/HD-SDI, LAN (IP) embedded
Audio Compression Format
AAC/MP3/G.711A
IP Interface
100M IP port (100BASE-TX)
Network Protocol
RTSP/RTMP, ONVIF, GBT28181; Visca over IP control protocol
Control Interface
RS232
Control Protocol
VISCA/Pelco-D/Pelco-P; Baud Rate: 115200/38400/9600/4800/2400
Power Interface
HEC380 outlet (DC12V), PoE (IEEE 802.3af)
Supply Adapter
AC110V-AC220V to DC12V/1.5A
Input Voltage
DC12V±10%
Input Current
1A (Max)
Consumption
12W (Max)
PTZ Parameters
Pan Rotation
270 degrees of pan (+/-135°)
Tilt Rotation
60 degrees of tilt (-30°
～
+30°)
Pan Control Speed Range
0.1 -60°/sec
Tilt Control Speed Range
0.1-30°/sec
Preset Speed
Pan: 60°/sec, Tilt: 30°/sec
Preset Number
255 presets (10 presets by remote controller)
Other Parameters
Store Temperature
-10
℃～
+60
℃
Store Humidity
20% - 95%
Working Temperature
-10
℃～
+50
℃
Working Humidity
20% - 80%
Dimension
145.4mm x 147mm x 154mm
Weight
2.8 lbs (1.27 Kg)
Use Environment
Indoor
Accessories in Box
Power adapter, IR remote controller, Thank You Card, Warranty Card
2.4 Interface Instruction
2.4.1 External Interface
1) External interfaces: Audio Input, 3G- SDI Output, Ethernet, RS232 input, DC12V Power.
Figure 2.3 external interface diagram
3. Application Instruction

CV605-BK/WH Manual
www.marshall-usa.com10 11
3.1 Remote Controller
3.1.1 Setting Explanation
1. Standby Key
After a 3 second press, the camera will go into standby mode. Long press 3 second press again,
camera will self-test again and move to HOME position. (Note: If power-on mode is turned on and
Preset 0 is set, and there is no operation within 12s, camera will automatically point to the
specified preset position.
2. Camera Address Selection
Select the camera address of which to control
3. Number Key
Set or run 0-9 presets
4, *, # Key
Key combination use
5. Focus Control Key
Auto Focus: Enter Auto focus mode.
Manual Focus: The camera focus mode is manual
Switch the camera focus mode to manual by pressing [focus +] or [focus -] to adjust manually.
6. Zoom Control Key
Zoom＋: Lens near or zoom in
Zoom－: Lens far or zoom out
7. Set or Clear Preset key:
Set Preset: Set preset key + 0-9 number key:
Clear Preset key: Clear preset key + 0-9 number key
8. Pan/Tilt Control Key
Press Key: Up
Press Key: Down
Press Key: Left
Press Key: Right
“HOME” Key: Return to the middle position or enter next level menu
9. BLC Control Key
Back Light ON / OFF: Turn back light on or off
10. Menu Setting
Open or close the OSD menu
Enter / Exit the OSD menu or return to the previous menu.
11. Camera IR Remote Control Address Setting
【*】+【＃】+【F1】:Camera Address No.1
【*】+【＃】+【F2】:Camera Address No. 2
【*】+【＃】+【F3】:Camera Address No. 3
【*】+【＃】+【F4】:Camera Address No. 4
12. Key Combination Functions
1)
【
#
】
+
【
#
】
+
【
#
】
:Clear all presets
2)
【
*
】
+
【
#
】
+
【
6
】
:Restore factory defaults
3)
【
*
】
+
【
#
】
+
【
9
】
:Flip switch
4)
【
*
】
+
【
#
】
+Auto: Enter into the aging mode
5)
【
*
】
+
【
#
】
+
【
3
】
:Menu set to Chinese
6)
【
*
】
+
【
#
】
+
【
4
】
:Menu set to English
7)
【
*
】
+
【
#
】
+Manual: Restore the default user name,
password, and IP address
8)
【
#
】
+
【
#
】
+
【
0
】
:Switch the video format to 1080P60
9)
【
#
】
+
【
#
】
+
【
1
】
: Switch the video format to 1080P50
10)
【
#
】
+
【
#
】
+
【
2
】
:Switch the video format to 1080I60
11)
【
#
】
+
【
#
】
+
【
3
】
:Switch the video format to 1080I50
12)
【
#
】
+
【
#
】
+
【
4
】
:Switch the video format to 720P60
13)
【
#
】
+
【
#
】
+
【
5
】
:Switch the video format to 720P50
14)
【
#
】
+
【
#
】
+
【
6
】
:Switch the video format to 1080P30
15)
【
#
】
+
【
#
】
+
【
7
】
:Switch the video format to 1080P25
16)
【
#
】
+
【
#
】
+
【
8
】
:Switch the video format to 720P30
17)
【
#
】
+
【
#
】
+
【
9
】
:Switch the video format to 720P25
3.1.2 Applications
After camera boot-up (initialize), camera can receive and execute IR commands. Press the remote controller button, the
indicator light will start flashing; release the button, the indicator light will stop flashing. Users can control the
pan/tilt/zoom, setting and operate preset positions via the IR remote controller.
Key Instruction:
1. In these instructions, “press the key” means a quick push rather than a long-press, and a special note will be provided
if a long-press is required (longer then one second).
2. When a key-combination is required, perform it in sequence. For example,“ 【*】+【#】+【F1】” means press“【*】”
first and then press“【#】” and then lastly press“【F1】”.
1) Camera Selection
Select the camera address to control.
2) Pan/Tilt Control
Up: press Down: press
Left: press Right: press
Back to middle position: press“【HOME】”
Press and hold the up/down/left/right key, the pan/tilt will keep
running, from slow to fast, until it runs to the maximum
endpoint; the pan/tilt movement will stop as soon as the key is
released.
3) Zoom Control
ZOOM IN: press “ZOOM “ key
ZOOM OUT: press “ZOOM ” key
Press and hold the key, the camera will keep zooming in or
zooming out and stops as soon as the key is released.
4) Focus Control
Focus (near):Press “【focus+】” key (Valid only in manual focus
mode)
Focus (far): Press “【focus-】”key (Valid only in manual focus
mode)
Auto Focus: Support
Manual Focus: Support
Press and hold the key, the action of focus will keep continue and
stops as soon as the key is released.
5) BLC Setting
BLC ON / OFF: support
6) Presets Setting, Running, Clearing

CV605-BK/WH Manual
www.marshall-usa.com12 13
1. Preset setting: to set a preset position, user should press the
“【SET PRESET】” key first and then press the number key 0-9 to
set a relative preset position,
Note: 10 preset positions in total are available on the remote
controller, 255 available from joystick or other command
sources.
2. Preset Running: Press a number key 0-9 directly to move
camera to the saved preset position.
Note: need to save a preset first, for each number to be assigned.
3. Preset clearing: to clear a preset position, the user can press the
“【CLEAR PRESET】” key first and then press the number key 0-9
to clear the relative camera preset position;
Note : press the“【
【
#】
】
” key three times to cancel all the presets.
7) Camera Remote Controller Address Setting
【
*
】
+
【＃】
+
【
F1
】
:Camera Address No.1
【*】+【＃】+【F2】:Camera Address No. 2
【*】+【＃】+【F3】:Camera Address No. 3
【*】+【＃】+【F4】:Camera Address No. 4
3.2 MENU SETTING
3.2.1 Main Menu
In normal working mode, press【MENU】key to display the OSD main menu. Use up/down arrows to select the menu and
press【HOME】to enter the menu.
MENU
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
(Language)English
(Setup)
(Camera)
(P/T/Z)
(Video Format)
(Network Settings)
(Audio Settings)
(Version)
(Restore Default)
[↑
↑
↓
↓
]Select [←
←
→
→
]Change Value
[Menu]Back [Home]OK
LANGUAGE: Language setting, English / Chinese
SETUP:System settings
CAMERA:Camera settings
PTZ:Pan tilt zoom settings
Video Format: select video output formats
Network Settings: turn DHCP mode on/off and check camera IP address
Audio Settings: turn audio on/off and adjust the volume
VERSION:display camera firmware version
Restore Default:Reset settings
[↑↓] Select:for selecting menu
[← →] Change Value:for modify parameters
[MENU] Back:Press [MENU] to return
[Home] OK:Press [Home] to confirm
3.2.2 System Setting
Move the pointer to (Setup) in the Main Menu, click the【HOME】key and enter into Setup menu as below.
PROTOCOL: VISCA/Pelco-P/Pelco-D/Auto
Visca Address: 1 ~ 7
PELCO-P Address: 1 ~ 255
PELCO-D Address: 1 ~ 255
Baud rate: 2400/4800/9600/38400/115200
Auto Flip: ON/OFF (When it’s ON, image will automatically flip if camera is mounted upside down)
3.2.3 Camera Setting
Move the pointer to (Camera) in the Main Menu, click the【HOME】key and enter into Camera menu as below.
SETUP
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
Protocol Auto
Visca Address 1
PELCO-P Address 1
PELCO-D Address 1
Baudrate 9600
Auto Flip OFF
[↑
↑
↓
↓
]Select [←
←
→
→
]Change Value
[Menu]Back

CV605-BK/WH Manual
www.marshall-usa.com14 15
EXPOSURE: Enter into Exposure settings
COLOR: Enter into color settings
Image: Enter into image setting s
Focus: Enter into focus settings
Noise Reduction: Enter into noise reduction
Style: choose picture style options (Default/Normal/Clarity/Bright/Soft)
1) EXPOSURE
Move the pointer to the (Exposure) menu, click the【HOME】key to enter into Exposure menu as follow,
Mode: Auto, Manual, Shutter priority, Iris priority and Bright.
EV: On/Off (only available in Auto mode)
EV Level: -7~7 (only available in Auto mode when EV is ON)
BLC: ON/OFF (only available in Auto mode)
Flicker:OFF/50Hz/60Hz for options (only available in Auto/Iris priority/Bright modes)
Gain Limit: 0~15(only available in Auto/ Iris priority /Bright modes)
DRC: Close, values 1~8
Shutter Priority:
1/25,1/30,1/50,1/60,1/90,1/100,1/120,1/180,1/250,1/350,1/500,1/1000,1/2000,1/3000,1/4000,1/6000,1/10000 (only
CAMERA
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
(Exposure)
(Color)
(Image)
(Focus)
(Noise Reduction)
Style Default
[↑↓]Select
[← →]Change Value
Back ok
EXPOSURE
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
Mode Auto
EV OFF
BLC OFF
Flicker 50Hz
G.Limit 4
DRC 4
[↑↓]Select [← →]Change Value
Menu Back
available in Manual and Shutter priority mode)
IRIS Priority: Close, F11, F9.6, F8.0, F6.8, F5.6, F4.8, F4.0, F3.4, F2.8, F2.4, F2.0, F1.8 (only available in Manual Exposure and
Iris priority mode)
Bright: 0~23 (only available in Bright priority mode)
2) COLOR
Move the pointer to the (Color) menu, click the【HOME】key to enter into Color menu as follow,
WB Mode: Auto, Manual, One Push, VAR
Color Temp: 2400K ~ 7100K (only available in VAR mode)
Red Gain: 0~255(only available in Manual mode)
Blue Gain: 0~255(only available in Manual mode)
Saturation: 60%,70%,80%,90%,100%,110%,120%,130%,140%,150%,160%,170%,180%,190%,200%
Hue: 0~14
AWB Sensitivity: High/Middle/Low (only available in Auto mode)
3) IMAGE
Move the pointer to the (Image) menu, click the【HOME】key to enter into the Image menu as follow,
Brightness: 0~14
Contrast: 0~14
COLOR
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
WB Mode Auto
Saturation 100%
Hue 7
AWB Sensitivity High
[↑↓]Select[← →]Change Value
[Menu]Back
IMAGE
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
Brightness 7
Contrast 7
Sharpness 6
Flip-H OFF
Flip-V OFF
B&W-Mode Color
Gamma Default
DZoom OFF
DCI Close
[↑
↑
↓
↓
]Select [←
←
→
→
]Change Value
Menu back

CV605-BK/WH Manual
www.marshall-usa.com16 17
Sharpness: 0~15
Flip-H: On/Off (When Auto Flip is ON, this option will be disabled)
Flip-V: On/Off (When Auto Flip is ON, this option will be disabled)
B&W Mode: Color, B&W
Gamma: Default, 0.45, 0.50, 0.55, 0.63
DZoom: ON/OFF
DCI (Dynamic Contrast): Close, 1～8
4) FOCUS
Move the pointer to the (Focus) menu, click the【HOME】key to enter into the Focus menu as follow,
Focus Mode: Auto, Manual, OnePush
AF-Zone: All, Top, Center, Bottom
AF-Sensitivity: High, Middle, Low
5) NOISE REDUCTION
Move the pointer to the (Noise Reduction) menu, click the【HOME】key to enter into Noise Reduction menu as follow,
2D Noise Reduction: Auto, OFF, 1~7
3D Noise Reduction: O F F, 1~ 8
Dynamic Hot Pixel: OFF, 1~ 5
3.2.4 P/T/Z
Move the pointer to the (P/T/Z) in the Main Menu, click the【HOME】key to enter into P/T/Z menu as follow,
FOCUS
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
Focus Mode Auto
AF-Zone All
AF-Sensitivity Low
[↑
↑
↓
↓
]Select [←
←
→
→
]Change Value
[Menu]Back
NOISE REDUCTION
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
NR-2D 3
NR-3D 3
Dynamic Hot Pixel OFF
[↑
↑
↓
↓
]Select [←
←
→
→
]Change Value
[Menu]Back
Speed by Zoom: ON/ Off (Only effective for IR remote controller. When this option is ON, the Pan/Tilt moving speed will
become slower when the image is zoomed in.)
Zoom Speed: 1~8 (Only effective for IR remote controller)
Image Freezing: On/Off
Preset speed: 1-10
3.2.5 Video Format
Move the pointer to the (Video Format) in the mian Menu, click the【HOME】key to enter into video format menu as follow,
3.2.6 Network settings
Move the pointer to the (Network Settings) in the Main Menu, click the【HOME】key to enter into network settings menu
as follow,
P/T/Z
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
Speed by Zoom ON
Zoom speed 8
Image Freezing OFF
Preset speed 1
[↑
↑
↓
↓
]Select [←
←
→
→
]Change Value
VIDEO FORMAT
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
1080P60 1080P59.94
1080P50 1080P30
1080P29.97 1080P25
1080I60 1080I59.94
1080I50 720P60
720P59.94 720P50
720P30 720P29.97
720P25
[↑
↑
↓
↓
]Select [Menu]Back
[Home]OK

CV605-BK/WH Manual
www.marshall-usa.com18 19
Note: Connect Ethernet cable to camera first. After setting DHCP to ON or OFF, save and exit by pressing Menu key to exit
OSD menu completely. Then power cycling the camera for IP address to take effect. The camera actual IP address will be
displayed in network settings menu after power cycling.
3.2.7 Audio settings
Move the pointer to the (Audio Settings) in the Main Menu, click the【HOME】key to enter into audio settings menu as
follow,
3.2.8 Version
Move the pointer to the (Version) in the Main Menu, click the【HOME】key to enter into version menu as follow,
MCU Version: Display MCU version information
Camera Version: Display camera version information
Network settings
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
DHCP ON
IP Addr: 192.168.5.163
Mask: 255.255.255.0
Gateway: 0.0.0.0
[←
←
→
→
]Change
[Menu]Back
Audio settings
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
Audio OFF
Volume 4
[↑
↑
↓
↓
]Select [←
←
→
→
]Change
[Menu]Back
VERSION
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
MCU Version V3.1.3 2021-7-28
Camera Version V1.0.1 2021-8-3
AF Version V4.0.4 2020-10-10
[Menu]Back
AF Version: Display the focus version information
3.2.9 Restore Default
Move the pointer to the (Restore Default) in the Main Menu, click the【HOME】key to enter the restore default menu as
follow,
Restore default: options: yes/no;
after restoring default, the video format restores to default. The things that are not restored are VISCA address, baud rate
and IP address.
4. Network Connection
4.1 Connecting Mode
Direct connection: Connect the camera directly to a computer by Ethernet cable.
Internet connection (DHCP): Connect the camera to Internet by Router or Switch and user can log in the device by browser.
Note: Please do not put the power and network cable in places where can be easily touched to prevent video quality
lowered by unstable signal transmission due to poor contact of cables.
Direct connection (Using Default IP):
The computer must have the network segment where the camera IP address belongs to. The device will not be accessible if
without the segment. I.E. The camera default IP address is 192.168.5.163, then segment 5 must be added in the computer.
Specific steps are as below:
First open Local Area Connection Properties on computer, select the “Internet Protocol Version 4(TCP/IPv4)” as shown
below. Double click “Internet Protocol Version 4(TCP/IPv4)” or click “Properties” to enter into the Internet Protocol Version
4(TCP/IPv4) Properties window. Under “General” tap, select “Use the following IP address”. Enter the static IP “192.168.5.26”
which has the same network segment as camera default IP address
and subnet mask “255.255.255.0” as picture below. Click “OK” to finish.
RESTORE DEFAULT
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
＝
Restore Default? NO
[↑
↑
↓
↓
]Select [←
←
→
→
]Change Value
[Menu]Back [Home]OK