Martello My Milky Pro User manual

M
MY MILKY PRO
MARTELLO My Milky Pro, Milk frother
MODEL: BVMTMMP402-033, My Milky Pro
INSTRUCTION MANUAL
www.martellocafe.ca ENGLISH: 1-22 | FRENCH: 23-44

2 MyMilky PRO
TABLE OF CONTENT EN
Table of content ...................................................................................2
Important Safeguards .................................................................... 3-6
Product Description ............................................................................7
First Use ........................................................................................... 8-9
Daily Use - Heating Milk ...............................................................10-11
Daily Use - Frothing Cold Milk .................................................... 12-13
Daily Use - Frothing & Heating ................................................... 14-15
Cleaning ....................................................................................... 16-17
Warranty .......................................................................................18-19
Recipes .........................................................................................20-21

MyMilky PRO 3
EN IMPORTANT SAFEGUARDS
1. READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE.
2. DO NOT touch hot surfaces. Use handles or knobs.
3. To protect against fire, electric shock and injury to persons do
not immerse cord, plugs, or appliance in water or other liquids.
4. Unplug unit from electrical outlet when not in use and before
cleaning. Allow it to cool before putting on or taking o parts and
before cleaning it.
5. DO NOT operate any appliance with a damaged cord or plug or after
the appliance malfunctions or has been damaged in any manner.
Return this appliance only to the nearest Authorized MARTELLO
Service Center for examination, repair or adjustment.
6. The use of accessory attachments not recommended for MARTELLO
products may result in fire, electric shock or injury to persons.
7. DO NOT use outdoors or for commercial purposes.
8. DO NOT let cord hang over edge of table or countertop or touch
hot surfaces.
9. DO NOT place this appliance on or near a hot gas or electric
burner or in a heated oven.
10. Always attach plug to appliance first, then plug cord into the wall
outlet. To disconnect, turn any control to “o”, then remove plug
from wall outlet.
When using electrical appliance, basic safety precautions should always be followed to
reduce the risk of fire, electric shock and/or injury to persons, including the following:

4 MyMilky PRO
IMPORTANT SAFEGUARDS EN
When using electrical aplliance, basic safety precautions should always be followed to
reduce the risk of fire, electric shock and/or injury to persons, including the following:
11. DO NOT use appliance for anything other than its intended use.
12. Use on a hard, flat level surface only, to avoid interruption of airflow
underneath the appliance.
13. Always be sure to install the milk container securely back on the
unit with its lid closed after filling with milk and before turning
appliance on.
14. DO NOT remove the milk container until unit is turned o.
15. This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given permission
or proper instruction concerning the use of the appliance by a person
responsible for their safety. Children should be supervised to ensure
that they DO NOT play with the appliance.
16. Scalding may occur if the lid is removed during the brewing cycles.
17. Keep the Opening Lever and the lid in place when the appliance is on.
Improper use of this appliance may result in injury
or damage to the product.

MyMilky PRO 5
EN IMPORTANT SAFEGUARDS
When using electrical aplliance, basic safety precautions should always be followed to
reduce the risk of fire, electric shock and/or injury to persons, including the following:
18. Close supervision is necessary when any appliance is used by or
near children, or incapacitated individuals.
19. This appliance is not intended to be operated by means of an
external timer or separate remote-control system.
20. To reduce the risk of injury, do not drape cord over the counter top
or table top where it can be pulled on by children or tripped over
unintentionally.
THIS UNIT IS FOR HOUSEHOLD ONLY.

6 MyMilky PRO
21. A short power-supply cord is to be provided to reduce risks resulting
from becoming entangled in or tripping over a longer cord.
22. Longer extension cords are available and may be used if care
is exercised in their use.
23. If a long extension cord is used: The marked electrical rating of the
detachable power-supply cord or extension cord should be at least
as great as the electrical rating of the appliance; The extension cord
should be a grounding-type 3-wire cord; The longer cord should be
arranged so that it will not drape over the counter top or table top
where it can be pulled on by children or tripped over.
SAVE THESE INSTRUCTIONS
The MARTELLO reserves the right to make changes without prior notification to the external
appearance of the product and / or technical conditions to improve the product. The
MARTELLO Superespresso AG trademark. Copyright @2014. All rights reserved
Technical Data:
Model »MyMilky Pro«, Type IDM15 (black) 120 Vac, 60Hz, 500W, Made in China.
IMPORTANT SAFEGUARDS EN
When using electrical aplliance, basic safety precautions should always be followed to
reduce the risk of fire, electric shock and/or injury to persons, including the following:

MyMilky PRO 7
EN PRODUCT DESCRIPTION
A | Removable
milk container with
cool-touch case
G | Plastic transparent lid
H | Rubber seal
D | Button for warm
frothing / Indicator light
C | Lever
E | Button for cold
frothing / Indicator light
I | Whisk
for frothing
F | Base
B | Heat-resistant
case

1 2 3 4
8 MyMilky PRO
Unpack the box with care,
keep all the packaging
materials until you are
satisfied everything is
present and in working
order.
Clean the milk container
(A) immediately after
each use. Flush and clean
the inner walls using
warm soapy water and a
non-abrasive cloth. Then
dry with a soft towel.
Remove the lid (G) from
the milk container (A) and
clean with warm soapy
water.
To disassemble unit for
cleaning, open levers
(C) from the base (F) by
pulling out and upward to
release the milk container
(A).
The instructions on this page are valid for the first set-up
of the device and for easy cleaning of the milk frother.
FIRST USE EN
WARNING: Never put the base (F) into dishwasher. Only the
milk container (A), lid (G) and whisk (I) are dishwasher safe.
Carefully read the instructions. Never use sharp cleaning agents,
hard nylon brush or metal brush to avoid scratches on the stainless
steel surface! Never clean with metal objects and never use
abrasives. Never immerse into water or other liquids.

5
MyMilky PRO 9
NOTE!
Never use sharp cleaning
objects such as hard
nylon or metal brushes or
abrasive cleaning agents
to avoid scratching on
the stainless steel surface
or on the inside of milk
container.
NOTE!
Never put the base (F)
in the dishwasher or
immerse into water or
other liquids.
Clean the base (F) with a
soft cloth.
EN FIRST USE

1
5
2
6
3
7
4
8
10 MyMilky PRO
Plug in the unit.
Ensure the rubber seal is
in place on the lid (G) and
remove the whisk (I) be-
fore placing back onto the
milk container (A). Close
both levers (C) by pressing
down and pushing in.
Caution with overfilling
to avoid frother from
overflowing.
Error status: If the indicator
light (D) keeps flashing,
this means the machine
is overloaded with milk.
Pull out the power cable
and pour some of the milk
out until you get below
the MAX line, plug the unit
back in and try again.
Put the milk container (A)
onto the base (F).
Unplug the connection
plug.
Pour the milk or
chocolate milk into
the milk container (A).
Pay attention to the
MAX capacity lines.
Push the button (D) for
heating milk. The indicator
light (D) will come on to
indicate the heater is on.
After heating is completed,
the indicator light (D)
will keep flashing for an
additional 30 seconds.
DAILY USE - HEATING MILK EN
ERROR

910
MyMilky PRO 11
Open the levers (C) and
carefully pull the levers
(C) out from the milk
container (A) and remove
lid (G).
Pour your heated milk
from the milk container
(A) into your coee or
milk drink.
EN DAILY USE - HEATING MILK

1
5
2
6
3
7
4
8
12 MyMilky PRO
Plug in the unit.
Ensure the rubber seal is
in place and the whisk (I)
is inserted before placing
lid (G) onto the milk
container (A). Close both
levers (C) by pressing
down and pushing in.
Caution with overfilling
to avoid frother from
overflowing.
Error status: If the indicator
light (E) keeps flashing. The
machine is overloaded
with milk. Pull out the
power cable and pour
some of the milk out until
you get below the MAX
line, plug the unit back in
and try again.
Put the milk container (A)
onto the base (F).
Unplug the connection
plug.
Pour the milk into the
milk container (A). Pay
attention to the MAX
capacity lines.
Pour the cold milk into
the milk container (A)
and push the button for
cold frothing (E) then
the indicator light (E) will
turn on. After approx. 65
seconds the cold frothing
is complete. After cold
frothing is complete, the
indicator light (E) will keep
flashing for an additional
30 seconds.
DAILY USE - FROTHING COLD MILK EN
ERROR

910
MyMilky PRO 13
Open the levers (C) and
carefully pull the levers
(C) out from the milk
container (A) and remove
lid (G).
Pour your frothed milk
from the milk container
(A) into your coee or
milk drink.
EN DAILY USE - FROTHING COLD MILK

1
5
2
6
3
7
4
8
14 MyMilky PRO
Plug in the unit.
Ensure the rubber seal is
in place and the whisk (I)
is inserted before placing
lid (G) onto the milk
container (A). Close both
levers (C) by pressing
down and pushing in.
Caution with overfilling
to avoid frother from
overflowing.
Error status: If the indicator
light (D) keeps flashing,
this means the machine
is overloaded with milk.
Pull out the power cable
and pour some of the milk
out until you get below
the MAX line, plug the unit
back in and try again.
Put the milk container (A)
onto the base (F).
Unplug the connection
plug.
Pour the milk into the
milk container (A). Pay
attention to the MAX
capacity lines.
Push the button (D) for
heating & frothing. The
indicator light (D) will
come on to indicate the
heater is on. After frothing
is completed, the indicator
light (D) will keep flashing
for an additional 30
seconds.
DAILY USE FROTHING & HEATING EN
ERROR

910
MyMilky PRO 15
Open the levers (C) and
carefully pull the levers
(C) out from the milk
container (A) and remove
lid (G).
Pour your frothed milk
from the milk container
(A) into your coee or
milk drink.
EN DAILY USE FROTHING & HEATING

1 2 3 4
16 MyMilky PRO
Unplug the unit. Remove the lid (G) from
the base (F), take the whisk
out and let cool. The whisk
can be removed from
the lid by pulling out.
Clean the milk frother
immediatley after
each use.
The Lid (G), Milk container
(A) and whisk (I) are
dishwasher safe (upper
rack). Place it carefully into
your dishwasher and store
in a safe place.
To disassemble unit for
cleaning, open levers (C)
from the bottom by pulling
out and upward to release
the milk container (A).
CLEANING EN
WARNING: The unit must be thoroughly cleaned after each use.
To clean, do not use any harsh chemicals, corrosive or abrasive cleaning agents.
IMPORTANT: Carefully read the instructions. Never use any
harsh chemicals, corrosive or abrasive cleaning agents to
clean your milk frother.

5 6
MyMilky PRO 17
NOTE!
Never use sharp cleaning
objects such as hard
nylon or metal brushes or
abrasive cleaning agents
to avoid scratching on
the stainless steel surface
or on the inside of milk
container. Never put the
base (F) in the dishwasher
or immerse into water or
other liquids.
Clean the base (F) with a
soft cloth.
EN CLEANING

18 MyMilky PRO
WARRANTY EN
1 Year Limited Warranty
Sunbeam Products, Inc. doing business as Jarden Consumer Solutions or if in Canada, Sunbeam Corpo-
ration (Canada) Limited doing business as Jarden Consumer Solutions (collectively “JCS”) warrants
that for a period of one year from the date of purchase, this product will be free from defects in material
and workmanship. JCS, at its option, will repair or replace this product or any component of the product
found to be defective during the warranty period. Replacement will be made with a new or remanu-
factured product or component. If the product is no longer available, replacement may be made with
a similar product of equal or greater value. This is your exclusive warranty. Do NOT attempt to repair or
adjust any electrical or mechanical functions on this product. Doing so will void this warranty.
This warranty is valid for the original retail purchaser from the date of initial retail purchase and is not
transferable. Keep the original sales receipt. Proof of purchase is required to obtain warranty perfor-
mance. JCS dealers, service centers, or retail stores selling JCS products do not have the right to alter,
modify or any way change the terms and conditions of this warranty.
This warranty does not cover normal wear of parts or damage resulting for any of the following: negli-
gent use or misuse of the product, use on improper voltage or current, use contrary to the operating
instructions, disassembly, repair or alteration by anyone other than JCS or an authorized JCS service
center. Further, the warranty does not cover: Acts of God, such as fire, flood, hurricanes and tornadoes.
What are the limits on JCS’s Liability?
JCS shall not be liable for any incidental or consequential damages caused by the breach of any ex-
press, implied or statutory warranty or condition.
Except to the extent prohibited by applicable law, any implied warranty or condition of merchantability or
fitness for a particular purpose is limited in duration to the duration of the above warranty.
JCS disclaims all other warranties, conditions or representations, express, implied, statutory or otherwise.
JCS shall not be liable for any damages of any kind resulting from the purchase, use or misuse of, or in-
ability to use the product including incidental, special, consequential or similar damages or loss of profits,
or for any breach of contract, fundamental or otherwise, or for any claim brought against purchaser by
any other party.
Some provinces, states or jurisdictions do not allow the exclusion or limitation of incidental or con-
sequential damages or limitations on how long an implied warranty lasts, so the above limitations or
exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights that vary from province
to province, state to state or jurisdiction to jurisdiction.

MyMilky PRO 19
EN WARRANTY
How To Obtain Warranty Service
In the U.S.A.: If you have any question regarding this warranty or would like to obtain warranty service,
please call 1.800.334.0759 and a convenient service center address will be provided to you.
In Canada: If you have any question regarding this warranty or would like to obtain warranty service,
please call 1.800.667.8623 and a convenient service center address will be provided to you.
IMPORTED BY: Sunbeam Corporation (Canada). Limited doing business as Jarden Consumer Solutions,
20 B Hereford Street, Brampton, Ontario L6Y 0M1. Sunbeam Products, Inc. is a subsidiary of Jarden
Corporation (NYSE:JAH).
PLEASE DO NOT RETURN THIS PRODUCT TO ANY OF
THESE ADDRESSES OR TO THE PLACE OF PURCHASE.
Printed in China IB Part # 177030

20 MyMilky PRO
LATTE MACCHIATO
40 ml MARTELLO -
Ristretto
210 ml milk
First heat/froth the milk with your milk frother MARTELLO
“My Milky Pro”. Fill the glass with the milk and foam and let
it rest for about 60 seconds. Now put the glass under the
coee outlet of your MARTELLO espresso machine and let
the coee pour into the glass, so that the coee builds a
layer between milk and milk foam.
VANILLA CAPPUCCINO
1 tbsp of vanilla sugar
50 ml milk
40 ml MARTELLO -
Crema Gusto
Some cocoa powder
Heat/froth the milk with your milk frother MARTELLO “My
milky Pro”. Then add vanilla sugar to the milk and stir it.
Prepare your Espresso from your MARTELLO espresso
machine as shown in the instruction manual. Now pour
the milk and foam into the coee mug, on top of the
Espresso. Finally put some cocoa powder on top.
RECIPES with MARTELLO CAFÈ · RECIPES with MARTELLO CAFÈ · RECIPES with MARTELLO CAFÈ · RECIPES with MARTELLO CAFÉ · RECIPES with MAR