Martha Stewart ZG-053-GY-MS User manual

Customer Service Email: [email protected] | Phone: [phone]
ASSEMBLY INSTRUCTIONS
Before You Begin:
Please identify all component parts and hardware pieces required before you begin. Carefully remove all of the
components from the packaging and set aside for assembly. Assemble on a soft surface to prevent scratching
during assembly.
Caution:
Tighten all components securely before use. Failure to do so may result in personal injury.
DO NOT use any sharp objects to open plastic wrapped components as damage to product or components may
result.
Warning:
CHOKING HAZARD - Small Parts. Adult Assembly Required.
DO NOT ALLOW CHILDREN TO CLIMB ON FURNITURE
Serious or fatal injuries can occur from furniture tipping over. You must install Tipping Restraint Hardware
(where included) to help prevent the unit from tipping and causing accidental injury, instability, death or
damage. The tipping restraint is intended only as a safety measure, it is not a substitute for proper adult
supervision.
To help prevent furniture from tipping over it must be permanently attached to the wall. Anti-Tip Safety Wall
Straps suitable for the unit weight and wall materials (if not included) should be purchased and installed.
Instruction Manual
Bookcase
SKU: ZG-053-GY-MS
SKU: ZG-053-WH-GLD-MS
SKU: ZG-053-GY-BK-MS

   
         
  
•    
    
    

•     
     
 
•    
  
    
   
 
•    
   
    
     
• 
 
 
 
 
 
      
 
WARNING
In order to help prevent overturning please follow these
instructions
1
!
•    
    
  
•    
    
  
•   
     
    
•    
     

•    
     
   
•     
     
  
•     
     
 
•     
   
•  
    
  

To help prevent product toppling over please follow the below
steps:
Use the anti tip strap or wall fixing method provided (if
applicable)
Do not allow children to climb or hang on the furniture
Do not place heavy items on top of the furniture, unless the
furniture has been designed for this purpose
Please note that only the anti-tip strap is provided. You will need
to provide wall anchors and screws applicable for your wall type.

Male Camlock x 6
A
D
Female Camlock x 6
B C
Dowel x 6
Tools required
Phillips screwdriver
(medium & large)
E
Hardware
Note:
may be supplied than is required.
Please check you have all the panels listed below
The quantities below are the correct amount to complete the assembly. In some cases more hardware
F
G I
6*20mm Screw x 12
J K
M
3.5*14mm Screw x 24
Ø20 Sticker x 20
Hex Key M4 x 1
H
Plastic Wedge x 18
3*17mm Screw x 18 4*25mm Screw x 2
4*40mm Screw x 3
L
Handle & Screws x 2
Anti-Tip Hardware Pack x 2
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
The screw length is measured from the head to the point (30mm screw shown).
N
Door Hinge x 4 6*50mm Screw x 4
O
P
Protective Feet x 4

Using Camlocks
12
DO NOT OVER TIGHTEN.
34
4
Step 1
Step 3
Step 2
Step 4
Connect the male camlock
as diected in the assembly
instructions using a
scewdriver.
Push the male camlock
into the entry hole.
Insert the female camlock
as shown in the
instruction.
Note：ensure that the
arrow on the top of the
camlock points towards
the entry hole for the
male camlock.
Turn the female camlock
clockwise with a
screwdriver.
You should feel a click
when the camlock is
locked in place.
The joint is now secure.
Adjusting Hinges
Hinge adjustment:
a: To move the top panel up or
down, loosen screws shown
and move top panel to suit
b.To move the top panel in or
out, loosen screws shown and
move top panel to suit.
Retighten screws
C:To move the top panel left
or right, adjust screws shown.
b:
a:
c:

Parts
1
2
3
4
6
5
7
7
8
9
9
10
10
10
11
12
12

Assembly Instructions
Step 1
Step 2
4
C
C
4
3
J
J
J

Step 3
Step 4
2
1
C
C
C
C
A
A
1 2 3
B
3
4
1

Step 5
Step 6
F
3
4
1
5
6
I
I
OO
O
F
A
A
A
A

Step 7
Step 8
9
1
5
3
EE
F
F
E
1 2 3
B
B
1
5
3

Step 9
Step 10
3
5
9
9
1
EE
F
3
1
5
9
9
10
10
7
7
8
F
E

Step 11
Step 12
1 2 3
3
5
9
9
1
2
B
B
1
2
3
9
9
E
E
E
E
1 2 3
B
F
E
O
F
O
O
! Adjust Part 3 as needed.

Step 13
Step 14
5
2
3
10
9
9
1
11
2
1
E
E
E
E
F
9
9
5
3
F
E
P
P
P
P

Step 15
Step 16
12 12 L
L
L
L
L
L
M
M
M
M
DD
DD
D
D
DD
12
DX4
DX4
1
DX4
DX4
5
3
12
M
M

Step 17
Step 18
DX4
DX4
12
1
DX4
DX4
5
3
12
M
M
G
H
H
X18
X18
X4
H
X4
H
X4
H
X6
H

Step 19
Step 20
The unit is floor
standing, but it is
recommended that the
unit is secured to the
wall.
1. Move the unit into
desired position.
2. Mark the wall with
a suitable scribe the
position of the fixing
holes.
Warning:
Before driling,check
wall for hidden pipes
and cables.
!
3. Drill holes and insert 2 x
wall plug
4. Attach 2 x Wall Straps to
to the top of the unit using 2
x Washers and 2 x Screws
5. Secure the straps to the
wall using 2 x Washers
and 2 x Screws
Note: To hide the straps
behind the unit, drill the
holes lower than the top of
the unit
N
N
Wall
Wall
N
N
1
2
3
KX20

A Guide to Wall Mounting & Hardware
Important note:
 f plastic wall anchors
are supplied with your
product, e.g.:
- these are only suitable for use in
masonry walls.
If you are in any doubt about the
correct wall anchors for your wall,
seek professional advice.
Failure of the product due to using
the incorrect hardware is the
responsibility of the installer.
m
Important: when drilling into walls always
check that there are no hidden wires or pipes etc.
Make sure that the screws and wall anchors being used are suitable
for supporting your unit. Consult a qualified trades person if you are unsure.
Hints:
1: General rule: Always use a larger screw and wall ancho r
2: Ensure you use the recommended drill bit to match the wall
anchor and hole size.
3: Ensure you drill the hole horizontally; do not force the drill or
enlarge the hole. Ensure wall anchors are inserted beyond the
thickness of the the hole.
4: Take extra care when drilling high walls, ceilings and ceramic
tiles.
5: Ensure wall anchors are well fitted and are a tight fit in the
drilled hole
pes of walls 


Generally aerated blocks should
not be used to support heavy
loads, use a specialist fitting in
this case. For light loads, general
purpose
wall anchors can be used.
No.2 " Plasterboard" wall anchor

For use with plasterboard
partitions or hollow wooden
doors.
No.4 " Cavity - Heavy Duty" 
wall anchor 

   
        
      
For use with walls stuck with
plasterboard. The hammer
anchor allows it to be fi xed to
the wall rather than the
plasterboard. Always check the
anchor iis secure to the retaining
wall.
No.6" Shield Anchor" wall
anchor - heavy loads
For use when attaching light
loads onto plasterboard
partitions.
 Care &
 Maintenance
For use when fitting or supporting
heavy loads such as shelving, wall
cabinets and coat racks.
Safety: always check the fitting
and location to ensure your safety in
and around the home.
For use with heavier loads such as
TV and HiFi speakers and satellite
dishes etc.
Fitting: from time to time check the
fitting to ensure the wall anchors or
screws do not become loose.
m
if y ou are not sure.

Quality and Safety Guidelines:
•Please follow the static and dynamic weight capacity limits provided on this item. If you are
unsure of the weight capacities for this product, email us at
[email protected] or call 866-552-2810.
•Please use this item on a stable, level surface only. All table legs should contact the flooring surface
when in use. Do not use this item if any instability is detected.
•Please install and use anti-tipping devices.
•For maintenance instructions and replacement parts, please email us at
[email protected] or call 866-552-2810.
•This item is intended as a table and shelving only, do not climb, stand or sit on this item.
•Do not use this item as a TV stand.
•The item is intended to be used indoors.
•For product longevity, product safety and product integrity, protect from wet or humid weather and
store indoors in a dry location.
•For additional storage instructions, please email us at [email protected] or
call 866-552-2810.
•Please visit www.theubiquegroup.com for our product warranty details or email us at
[email protected] or call 866-552-2810.