Martha Stewart ZG-ZP-028-WH-GLD-MS User manual

Customer Service Email: [email protected] | Phone: [phone]
ASSEMBLY INSTRUCTIONS
Before You Begin:
Please identify all component parts and hardware pieces required before you begin. Carefully remove all of the
components from the packaging and set aside for assembly. Assemble on a soft surface to prevent scratching
during assembly.
Caution:
Tighten all components securely before use. Failure to do so may result in personal injury.
DO NOT use any sharp objects to open plastic wrapped components as damage to product or components may
result.
Warning:
CHOKING HAZARD - Small Parts. Adult Assembly
Required. DO NOT ALLOW CHILDREN TO CLIMB
ON FURNITURE
Serious or fatal injuries can occur from furniture tipping over. You must install Tipping Restraint Hardware
(where included) to help prevent the unit from tipping and causing accidental injury, instability, death or
damage. The tipping restraint is intended only as a safety measure, it is not a substitute for proper adult
supervision.
To help prevent furniture from tipping over it must be permanently attached to the wall. Anti-Tip Safety Wall
Straps suitable for the unit weight and wall materials (if not included) should be purchased and installed.
Instruction Manual
Home Office Desk
SKU: ZG-ZP-028-WH-GLD-MS
SKU: ZG-ZP-028-GY-BK-MS
SKU: ZG-ZP-028-BR-GLD-MS
SKU: ZG-ZP-028-BR-BK-MS

Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Care and maintenance
•Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
•From time to time check that
there are no loose screws on
this unit.
•This product should not be
discarded with household waste.
Take to your local authority waste
disposal center.
Handy Hints
•Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
•To reduce the
likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
WARNING
In order to help prevent overturning –
1
!
•Check you have all the
components and tools listed on
the following pages.
•Remove all fittings from the
plastic bags and separate them
into their groups.
•Keep children and animals
away from the work area, small
parts could choke if swallowed.
•Make sure you have enough
space to layout the parts before
starting.
•During assembly do not stand
or put weight on the product,
this could cause damage.
•Assemble the item as close to
its final position (in the same
room) as possible.
•Assemble on a soft level surface
to avoid damaging the unit or
your floor.
•Parts of the assembly will be
easier with 2 people.
•Regularly check and ensure
That all bolts and fittings are
tightend properly.
please follow these instructions
To help prevent product toppling over please follow the below steps:-
Use the anti tip stap or wall fixing method provided (if applicable)
Do not allow children to climb or hang on the furniture
Do not open more than one drawer at a time
Do not place heavy items in the top drawers
Do not place heavy items on top of the furniture, unless the furniture has been
designed for this purpose
please note that only the anti tip strap is provided.
You will need to provide wall plugs and screws applicable for your wall type

Male Camlock x 40
A
D
Female Camlock x 44
B C
Dowel x 20
Tools required
Phillips screwdriver
(medium & large)
E
Hardware
Note:
may be supplied than is required.
Please check you have all the panels listed below
The quantities below are the correct amount to complete the assembly. In some cases more hardware
F
G H I
6*30mm Screw x 6
Hex Key M4 x 1
4*30mm Screw x 12
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
The screw length is measured from the head to the point (30mm screw shown).
3.5*14mm Screw x 24Drawer slider 14" X 3
Handle & Fixings x 3 Rubber Foot Pad x 8
J
6*40mm Screw x 8 4*14mm Screw x 3
K L
4*28mm Screw x 4
Male Camlock x 4
N

Using Camlocks
12
DO NOT OVER TIGHTEN.
NE PAS SERRER EXCESSIVEMENT.
34
4
Step 1
Step 3
Step 2
Step 4
Connect the male
camlock as diected in
the assembly instructions
using a scewdriver.
Push the male camlock
into the entry hole.
Insert the female
camlock as shown in the
instruction.
Note：ensure that the
arrow on the top of the
camlock points towards
the entry hole for the
male camlock.
Turn the female camlock
clockwise with a
screwdriver.
You should feel a click
when the camlock is
locked in place.
The joint is now secure.

Parts
1
2
1
2
3
4
10
5
6
7
8
9
11
12
13
14
15
11
12
13
14
15
11
12
13
14
15

Assembly Instructions
Step 1
Step 2
Ball Bearing Slide
Ball Bearing Slide Slider runner
Slider runner
D2
D1
D1
D2
X3
1
1
C
C
C
C
C
C
C
C

Step 3
Step 4
D1
E
E
D1
D1
E
E
E
E
1
1
2
2
C
C
C
C
C
C
C
C

Step 5
Step 6
15
15
D1
D1
E
E
E
E
°
D1
E
E
D1
E
E
X2
4
C
C
AA
A
A
A
A
A
A
One Side The Other Side

Step 7
Step 8
1 2 3
3
A
A
A
A
A
A
A
A
C
C
B
B
B
B
3
1
2

Step 9
Step 10
1 2 3
B
B
B
B
3
1
1
2
2
1 2 3
3
2
2
1
1
4
B
B
B
B
B
BB
B

Step 11
Step 12
5
6
N
N
N
N
5
4
3
1
1
2
2
1 2 3
B
B

Step 13
Step 14
1 2 3
B
B
5
6
4
1
2
2
5
6
7
3
3
8
9
J
J
J
J
J
J
J
J

Step 15
Step 16
7
9
5
6
K
K
K
K
7
3
3
5
6
9
L
L
L
L
8
3
L
3
8

Step 17
Step 18
I
I
I
I
I
I
I
I
A
A
A
A
A
A
A
A
A
A
A
A
10

Step 19
Step 20
1 2 3
BX12
5
6
9
10
H
H
H
5
H
H
H
10

Step 21
Step 22
H
H
H
5
6
9
10
H
H
H
X3
E
E
E
E
D2
D2
12
13

Step 23
Step 24
X3
AA
A
A
11
13
12
11
BB
B
B
X3

Step 25
Step 26
X3
11
12
13
14
14
12
13
15
X3
FF
F
F
11

Step 27
Step 28
11
X3
G
G
G
Slider bracket
secondary
11
11
11

Step 29