Martin Easypix 300 User manual

Easypix™
user manual

Dimensions
All dimensions are in millimetres
Easypix™300 / Easypix™1200
Easypix Power™
©2010 Martin Professional™ A/S. Information subject to change
without notice. Martin Professional A/S and all affiliated companies
disclaim liability for any injury, damage, direct or indirect loss,
consequential or economic loss or any other loss occasioned by the
use of, inability to use or reliance on the information contained in this
manual. The Martin logo, the Martin name and all other trademarks in
this document pertaining to services or products by Martin Professional
A/S or its affiliates and subsidiaries are trademarks owned or licensed
by Martin Professional A/S or its affiliates or subsidiaries. The use of
certain patents in Martin Easypix products is licensed by Color Kinetics,
Inc. (see details printed on product).
P/N 35005006, Rev. C

Safety Information
Warning! Read the safety precautions in this section before
installing, powering, operating or servicing this product.
The following symbols are used to identify important safety information
on the product and in this manual:
DANGER!
Safety hazard.
Risk of severe
injury or death.
Warning!
Hazardous
voltage. Risk
of lethal or
severe electric
shock.
Warning!
LED light
emission. Risk
of eye injury.
Warning!
Burn hazard.
Hot surface.
Do not touch
Warning!
Refer to user
manual.
Warning! Class 1M LED product according to IEC/EN 60825-1. Do
not view the light output with optical instruments or any device
that may concentrate the beam.
This product is for professional use only. It is not for household use.
This product presents risks of severe injury or death due to fire hazards,
electric shock and falls.
Read this manual before installing, powering or servicing the product,
follow the safety precautions listed below and observe all warnings in
this manual and printed on the luminaire. Install and operate the
luminaire only as described in this manual and in accordance with local
laws and regulations. Refer any operation not described in this manual
to a qualified technician.
If you have questions about how to operate the luminaire safely, please
contact your Martin dealer or call the Martin 24-hour service hotline at
[phone], or in the USA on 1-888-tech-180.
PROTECTION FROM ELECTRIC SHOCK
•Shut down power to the entire installation at the main power
distribution board and lock out power (by removing the fuse for
example) before carrying out any installation or maintenance work.

•Disconnect the luminaire from AC power before removing or installing
any cover or part and when not in use.
•System does not support hot swap. Turn off AC power before adding
any luminaire to the system.
•Connect the Easypix Power electrically to ground (earth).
•Use only a source of AC power that complies with local building and
electrical codes and has both overload and ground-fault (earth-fault)
protection.
•Before using the devices, check that all power distribution equipment
and cables are in perfect condition, are rated for the current
requirements of all connected devices.
•Isolate all devices from power immediately if any cable, seal, cover or
other component is damaged, cracked or deformed. Do not reapply
power until repairs have been completed.
•The Easypix is for indoor use only.
•Refer any service operation not described in this manual to an
authorized Martin Service partner.
PROTECTION FROM BURNS
•Do not operate the devices if the ambient temperature (Ta) exceeds
40°C (104°F).
•The exterior of the luminaires and Easypix Power becomes hot, up to
65°C (149°F) during normal operation. Ensure that accidental
physical contact with the devices is impossible.
•Allow the luminaire to cool for 5 minutes before servicing.
•Keep combustible materials (for example fabric, wood, paper) at least
20 cm (8 in.) away from the devices.
•Keep flammable materials well away from the devices.
•Do not modify the Easypix Power or luminaires in any way not
described in this manual or install other than genuine Martin parts.
•Use only Martin approved accessories to mask or modify the light
beam.
•Do not attempt to bypass fuses. Replace defective fuses with ones of
the specified type and rating only.
•Install the devices indoors in a well-ventilated area only. Provide a
minimum clearance of 5 cm (2 in.) and ensure unrestricted airflow
around the Easypix Power and the luminaires.

PROTECTION FROM INJURY
•Do not look at LEDs with a magnifying glass or any other optical
instrument that may concentrate the light output.
•Ensure that all external covers, components and installation fittings
are securely fastened.
•Block access below the work area and work from a stable platform
whenever installing, servicing or moving the devices.
•Ensure that all supporting structures, surfaces, fasteners and lifting
equipment can bear the weight of all the devices they are intended to
support plus an adequate safety margin, and that they conform to
local building and safety regulations.
•Use a sufficient number of fasteners with sufficient corrosion
resistance, dimensions and strength to mount the DIN rail safely. Any
nuts used must be self-locking.
•If the Easypix Power or luminaires are to be installed in a location
where injury or damage may be caused if a device falls, use a
secondary means of attachment such as safety wires looped tightly
around the devices and anchored securely to the mounting structure
or in the mounting surface.
Disposing of this product
Martin™ products are supplied in compliance with Directive
2002/96/EC of the European Parliament and of the Council of
the European Union on WEEE (Waste Electrical and Electronic
Equipment), as amended by Directive 2003/108/EC, where
applicable.
Help preserve the environment! Ensure that this product is
recycled at the end of its life. Your supplier can give details of
local arrangements for the disposal of Martin products.