Maruson CP-SV414-360W User manual

Surveillance UPS

12VDC / 24VAC Battery Power Backup for CCTV Cameras.
Automatic Voltage Regulation (AVR) for Wide Input Operation Voltage and Stable
Output Voltage.
12-13VDC Adjustable Output Voltage to Enhance Video Quality for Long-Distance
Cameras.
9/18 Ports Overload Protection (fuse optional) for CCTV Cameras.
Batteries are Hot Swappable (cameras, DVR, & monitors are always on).
Multi-LED Indicators for AC/DC Power Supply and UPS Power Status.
2 Amp Fuse or PTC (Break) Power Protection for High Power CCTV Cameras.
Two AC Outlets (NEMA 5-15R/110V or IEC/220V) with Battery Backup and Surge
Protection for DVR and Monitor.
Cameras Power Failure and AC Power Failure Notification through DVR/ NVR or
Alarm System.
Applications: Provides battery backup, noise filtering, and surge protection for
12VDC/24VAC cameras, monitor and DVR/NVR systems.
The Surveillance UPS Series is an innovative and professional battery backup solution
for all your surveillance needs. You will be kept at ease knowing that during a power
outage, your CCTV camera and DVR/NVR equipment will continue running so you can
keep monitoring and recording your premises.

SW1 2012-2-15
IPS-SW-006 COD E:2
-4

-5
3
1. Input Fuse
2. AC Input
3. AC Output
4. Fan : Operating on battery mode and overheat *
* Model CP-SV414-360W and CP-SV018-360W only
4
SW1 2012-2-15
IPS-SW-00 6 COD E:2
4 3 2

-6
When AC power fails, “NC” and “NO” connection will
provide a notification signal to the DVR/NVR or alarm system.
Majority of DVR/NVR systems also have e-mail alert features
to send notification of AC power failure.
Long-distance cameras tend to lose voltage due to distance
from power source. Setting Vdc to a high setting will improve
long-distance camera picture quality.
321
UPS Bypass Switch
A) UPS Mode: Unit will go into backup mode if power fails.
B) AC Bypass Mode: Switch to this mode when batteries need to be changed or UPS is
abnormal. “AC Bypass” mode will continue to offer power to cameras, DVR and monitor.
1.
3.
4.
2.
1
3
4
2

1
12V D C 24VA C
*
Dip switrch ports need to be switch to ON for the DC camera ports and DVR /NVR to receive DC power failure
notication.
*
You can only turn dip switches ON with ports number you have your camera connected to.
* You will get an wrong message if you switch ON with ports that have no camera connected.
M o d e l
CP-SV009-250W
CP-SV414-360W
1A , Green LED , Port : 5 - 9
2A , Orange LED, Port : 1 - 4
1A , Green LED, Port : 5 - 14
2A , Orange LED Port : 1 - 4,
N / A
1A , Orange LED , Port 15 - 18
1) Connect all camera ports before connecting battery.
2) Connect battery before turning on UPS. (bypass switch must also be in “ UPS mode ”
7
65
7.
6.
5. 24VAC Port 15 ~Port 18 (CP-SV414-360W )
12VDC Port 15 ~ Port 18 (CP-SV018-360W)
Model
CP-SV009-250W
CP-SV414-360W
Camera DC Power Failure
Notication Setting Dip Switch
Po rt: 1 -9
Po rt: 1 -1 4
Camera Power Failure Notication Port
1. COM : NC
2. COM : NO
Normal Close
Normal Open
8. 12VDC Port 1 ~ Port 9 ( CP-SV009-250W )
12VDC Port 1 ~ Port 14 ( CP-SV414-360W )
12VDC Port 1 ~ Port 14 ( CP-SV018-360W )
CP-SV018-360W 1A , Green LED, Port : 5 - 18
2A , Orange LED , Port : 1 - 4 N / A
CP-SV018-360W
8

-8
5.2 Turning off the unit: Push the button for 4 seconds to turn the UPS power off.The
UPS will turn off power completely within 10 seconds if there is a utility failure
during off mode. If the utility power is normal, the UPS will continue to charge
the battery.
When utility power is normal, please unplug the power cord if you want to turn
off the UPS completely.
5.3 DC start: During a blackout, push the button for 4 seconds to turn on the UPS
and enter into back-up mode. To turn off the power from UPS, please push the
button for 4 seconds. After turning off the UPS, please wait for 10 seconds if you
need to DC-start the UPS again.

-9
This unit is shipped from the factory with its internal battery fully charged, however,
some charge may be lost during shipping and the battery should be recharged prior
to use. Plug the unit into an appropriate power supply and allow the UPS to charge fully
by leaving it plugged in for at least 10 hours.
2 beeps every
8 seconds
STATUS YELLOW LED GREEN LED RED LED BUZZER
Backup
Mode
Battery normal
Load normal
No load (For green mode
function only)
Over load (will shut down
at 120% of full load)
Over Temperature
O/P short circuit
Low battery
Over battery voltage
(For external battery)
Inphase lock (AC good,
PLL working)
2 flashes every
4 seconds
One flash every
4 seconds
2 flashes every
4 seconds
32 flashes every
other 2 seconds
32 flashes every
other 2 seconds
4 flashes every
second
8 flashes every
second
OFF 4 flashes
every second
One beep every
8 seconds
Continuous beep
Depending on
load situation
32 beeps every
other 2 seconds
4 beeps every
second
8 beeps every
second
STATUS YELLOW LED GREEN LED RED LED BUZZER
AC
normal
mode
Battery full
Battery charge 70%~90%
Battery charge 50%~70%
Battery charge 30%~50%
Battery charge 0%~30%
Over load(shut off at 120% of full load)
OFF
OFF
OFF
OFF
OFF
OFF
Continuous ON
One blink every 8 seconds
One blink every 4 seconds
One blink every 2 seconds
One blink every second
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Continuous
Beep★
STATUS YELLOW LED GREEN LED RED LED BUZZER
OFF
mode
AC I/P disconnected
(UPS OFF completely)
AC I/P normal (Batt. In charging)
UPS timer is set (Through RS232)
OFF
OFF
1 flash every
2 seconds
1 flash every
2 seconds
1 flash every
2 seconds
OFF
OFF
OFF
Note” ”:The buzzer will keep continuous beeping until the control button is pushed for one second.★
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF OFF

-10