Maruson TAC-HV1K User manual

TACOMA HV SERIES
1K ~ 3KVA
On-Line UPS
USER MANUAL
Maruson Technology Corporation
P.O. Box1986, Walnut, CA91788 USA
Toll Free: 1-888-MARUSON
Website: www.MarusonUSA.com | E-Mail: [e-mail]
*Copyright ©2012 All RightsReserved.Maruson® isa registered trademark ofMaruson Technology
(U.S.TrademarkReg. No.3,150,957). Allothertrademarksarethepropertyoftheirrespectiveowners.
Productspecifications are subject to change without notice. Battery backup time is based on half load
and varies with equipment, configuration, battery age, temperature, etc.

CONTENT
1. Safety and EMC Instructions.....................................................1
1.1 Installation.........................................................................................1
1.2 Operation..........................................................................................2
1.3 Maintenance, servicing and faults....................................................3
1.4 Transport...........................................................................................4
1.5 Storage .............................................................................................4
1.6 Standards..........................................................................................5
2. Description of Commonly Used Symbols...................................6
3. Introduction .............................................................................7
4. Panel Description.....................................................................8
5. Connection and Operation ......................................................12
5.1 Inspection: ......................................................................................12
5.2 Connection:.....................................................................................12
5.3 Battery charge: ...............................................................................14
5.4 Turn on the UPS:............................................................................14
5.5 Test function:...................................................................................15
5.6 Turn off the UPS:............................................................................15
5.7Audible alarm mute function:..........................................................16
5.8 Operationprocedure of external battery for long backup time model
(“L” model) ............................................................................................16
6. Operating Mode for All Models ................................................18
6.1 Line mode.......................................................................................18
6.2 Battery mode ..................................................................................19
6.3 Bypass mode..................................................................................21
6.4 NO output mode.............................................................................21
6.5 EPO (Emergency Power Off).........................................................22

6.6 ECO mode (Economy mode).........................................................22
6.7 Converter mode..............................................................................23
6.8Abnormal mode ..............................................................................23
7. Setting by LCD Module...........................................................24
8. Trouble Shooting....................................................................27
9. Maintenance ..........................................................................31
9.1 Operation........................................................................................31
9.2 Storage ...........................................................................................31
9.3 Battery Replace..............................................................................31
10. Technical Data......................................................................32
10.1 Electrical specifications................................................................32
10.2 Operating Environment ................................................................32
10.3Typical backup time (Typical values at 25°C in minutes:)................33
10.4 Dimensions and weights ..............................................................33
11. Communication Port .............................................................34
11.1 USB...............................................................................................34
11.2AS400 Interface (Option)..............................................................34
12. Software...............................................................................35
Appendix: Rear panel.................................................................36

-
38
-
614-06810-02
-
1
-
1. Safety and EMC Instructions
Please read carefully the following user manual and the
safety instructions before installing the unit or using the unit!
1.1 Installation
See installation instructions before connecting to the supply.
Condensation may occur if the UPS is moved directly from a cold
to a warm environment. The UPS must be absolutely dry before
being installed. Please allow an acclimatization time of at least
two hours.
Do not install the UPS near water or in damp environment.
Do not install the UPS where it would be exposed to direct
sunlight or near heat.
Do not connect appliances or items of equipment which would
overload the UPS (e.g. laser printers, etc) to the UPS output.
Place cables in such a way that no one can step on or trip over
them.
Assure to connect withthe earth reliably.
Assure external battery source must be earthed.
Connect the UPS only to an earthed shockproof socket outlet.
The building wiring socket outlet (shockproof socket outlet) must
be easily accessible to close to the UPS.
With the installation of the equipment, the sum of the leakage
current of the UPS and the connected load does not exceed
3.5mA.
Do not block ventilation openings in the UPS’s housing. Ensure
the air vents on the front, side and rear of the UPS are not
blocked. Allow at least 25cm of space on each side.

-
2
-
UPS has provided earthed terminal, in the final installed system
configuration, equipotential earth bonding to the external UPS
battery cabinets.
An appropriate disconnect device as short-circuit backup
protection should be provided in the building wiring installation.
Please see the disconnect device specification in chapter 5.2.
Equipment the powered more than one source.
1.2 Operation
Do not disconnect the mains cable on the UPS or the building
wiring socket (grounded shockproof socket) during operation as
this would remove the ground to the UPS and of all connected
loads.
The UPS features its own, internal current source (batteries). You
may be electric shock when you touch the UPS output sockets or
output terminal block even if the UPS is not connected to the
building wiring socket.
In order to fully disconnect the UPS, first press the OFF button to
turn off the UPS, then disconnect the mains lead.
Ensure that no liquid or other foreignobjects can enter the UPS.
-
37
-
Back View of 3K
Back View of 3KL
Breaker(16A)
USB
EPO
Cooling Fan
Input Socket(16A)
Intelligent Slot
Battery connector
Output Socket
Fuse
Output Terminal
Breaker(20A)
USB
EPO
Cooling Fan
Input Terminal
Intelligent Slot
Battery connector
Output Socket
Fuse
Output Terminal

-
36
-
Appendix: Rear panel
Back View of 1K(L)
Back View of 2K(L)
Breaker
USB
EPO
Cooling Fan
Input Socket
Intelligent Slot
Battery connector
Output Socket
Breaker
USB
EPO
Cooling Fan
Input Socket
Intelligent Slot
Battery connector
Output Socket
-
3
-
Do not remove the enclosure. This system is to be serviced by
qualified service personnel only.
Remove the protective panelonly after disconnecting the terminal
connections.
Use No. 12 AWG (for 2-3K/KLinput wire) , 90¡C copper wire and
4.4 lb-in Torque force when connecting to terminal block.
Use No. 12AWG (for 2K/KL output wire) and No. 8AWG (for
3K/KL output wire), 90¡C copper wire and 12 lb-in Torque force
when connecting to terminal block.
1.3 Maintenance, servicing and faults
The UPS operates with hazardous voltages. Repairs may be
carried out only by qualified maintenance personnel.
Caution - risk of electric shock. Even after the unit is
disconnected from the mains power supply (building wiring
socket), components inside the UPS are still connected to the
battery which are potentially dangerous.
Before carrying out any kind of service and/or maintenance,
disconnect the batteries. Verify that no current is present and no
hazardous voltage exists in the capacitor or BUS capacitor
terminals.
Batteries must be replaced only by qualified personnel.
Caution - risk of electric shock. The battery circuit is not isolated
from the input voltage. Hazardous voltages may occur between
the battery terminals and the ground. Verify that no voltage is
present before servicing!
Batteries have a high short-circuit current and pose a risk of
shock. Take all precautionary measures specified below and
any other measures necessary when working with batteries:
remove all jewellery, wristwatches, rings and other metal
objects

-
4
-
use only tools with insulated grips and handles.
When changing batteries, replace with the same quantity and the
same type of batteries.
Do not attempt to dispose of batteries by burning them. It could
cause explosion.
Do not open or destroy batteries. Effluent electrolyte can cause
injury to the skin and eyes. It may be toxic.
Please replace the fuse only by a fuse of the same type and of
the same amperage inorder to avoid fire hazards.
Do not dismantle the UPS, except the qualified maintenance
personnel.
1.4 Transport
Please transport the UPS only in the original packaging (to
protect against shock and impact).
1.5 Storage
The UPS must be stockpiled in the room where it is ventilated
and dry.
-
35
-
12. Software
Free Software Download – WinPower
WinPower is a brand new UPS monitoring software, which provides
user-friendly interface to monitor and control your UPS. This unique
software provides safely auto shutdown for multi-computer systems while
power failure. With this software, users can monitor and control any UPS
on the same LAN no matter how far from the UPSs.
Installation procedure:
1. Go to the website:
http://www.ups-software-download.com/
2. Choose the operation system you need and follow the instruction
described on the website to download the software.
3. When downloading all required files from the internet, enter the serial
No: 511C1-01220-0100-478DF2A to install the software.
When your computer restarts, the WinPower software will appear as a
greenplug icon located in the system tray, near the clock.

-
34
-
11. Communication Port
The communication port is for the monitoring software. A USB port
and anintelligent slot are provided.
11.1 USB
The USB port is compliance with USB 1.1 protocol.
11.2 AS400 Interface (Option)
Except for the communication protocol as mentioned above, this
series UPS has AS400 card (an optional accessory) for AS400
communication protocol. Please contact your local distributor for
details. The following is the pin assignment and description of DB-9
connector inAS400 card.
Pin #
Description I/O Pin #
Description I/O
1 UPS Fail Output 6 Bypass Output
2 Summary Alarm
Output 7 Battery Low Output
3 GND Input 8 UPS ON Output
4 Remote
Shutdown Input 9 Line Loss Output
5 Common Input
DB-9 Interface of AS400 communication protocol
-
5
-
1.6 Standards
* Safety
IEC/EN 62040-1
* EMI
Conducted Emission.................................:IEC/EN 62040-2 Category C1
Radiated Emission....................................:IEC/EN 62040-2 Category C1
Harmonic Current....................................:IEC/EN 61000-3-2
Voltage Fluctuation and Flicker...............:IEC/EN 61000-3-3
*EMS
ESD........................................................:IEC/EN 61000-4-2 Level 4
RS..........................................................:IEC/EN 61000-4-3 Level 3
EFT.........................................................:IEC/EN 61000-4-4 Level 4
SURGE..................................................:IEC/EN 61000-4-5 Level 4
CS………………………………….....…...:IEC/EN 61000-4-6 Level 3
MS………………………………....……..: IEC/EN 61000-4-8 Level 3
Voltaje Dips………………………...…...: IEC/EN 61000-4-11
Low Frequency Signals..........................:IEC/EN 61000-2-2

-
6
-
2. Description of Commonly Used Symbols
Some or all of the following symbols may be used in this manual. It is
advisable to familiarize yourself with them and understand their
meaning:
-
33
-
10.3 Typical backup time (Typical values at 25°C in minutes:)
Model No. 100 % Load 50 % Load
1K 5 14
2K 9 21
3K 5 15
10.4 Dimensions and weights
Model No. Dimensions W×D×H (mm) Net Weight (kg)
1K 145×400×220 13
1KL 145×400×220 7
2K 192×460×347 31
2KL 192×460×347 13
3K 192×460×347 31
3KL 192×460×347 13

-
32
-
10. Technical Data
10.1 Electrical specifications
INPUT
Model No. TAC-
HV1K
TAC-
HV1KL
TAC-
HV2K
TAC-
HV2KL
TAC-
HV3K TAC- HV3KL
Phase Single
Frequency (45~55)/(54~66) Hz
Current(A) 5A 7A 9A 14A 14.5A 18A
OUTPUT
Model No. 1K(L) 2K(L) 3K(L)
Power rating
1kVA/0.8kW 2kVA/1.6kW 3kVA/2.4kW
Voltage 200/208/220/230/240×1 2% VAC
Frequency 50/60±0.2Hz (Battery mode)
Wave form sinusoidal
Derating to 90% when the output voltage is adjusted to 208VAC
Derating to 80% when the output voltage is adjusted to 200VAC
BATTERIES
Model No. 1K 2K 3K
Number and type
3×12V 7Ah 8×12V 7Ah 8×12V 7Ah
10.2 Operating Environment
Ambient Temperature 0oC to 45oC
Operating humidity < 95%
Altitude < 1000m
Storage temperature 0oC to 45oC
-
7
-
3. Introduction
This On-Line-Series is an uninterruptible power supply incorporating
double-converter technology. It provides perfect protection specifically
for Novell, Windows NT and UNIX servers.
The double-converter principle eliminates all mains power disturbances.
A rectifier converts the alternating current from the socket outlet to direct
current. This direct current charges the batteries and powers the
inverter. On the basis of this DC voltage, the inverter generates a
sinusoidal AC voltage, which permanently supplies the loads.
Computers and periphery are thus powered entirely by the mains
voltage. In the event of power failure, the maintenance-free batteries
power the inverter.
This manual covers the UPS listed as follows. Please confirm whether it
is the model you intend to purchase by performing a visual inspection of
the Model No. on the rear panel of the UPS.
“L” Model: Extended backup time
Model No. Type Model No. Type
1K 1KL
2K 2KL
3K Standard 3KL
Extended backup
time