Masco LaGard LG BASIC User manual

3765-2 Dual-Handed Swingbolt Lock Instructions
OPENING THE LOCK
➀Enter valid six (6) digit code.
➁The lock will indicate a valid code entry with a double signal.
➂Within four (4) seconds, turn handle to the open position.
④Pull door open.
●Invalid Code Entry - Lock will signal three (3) times.
●Security Considerations -On safes using more than one
lock the swingbolt lock must lock first.
CHANGING YOUR CODE
ALWAYS PERFORM THIS OPERATION WITH
THE DOOR OPEN
➀Enter “zero” six times.
➁Enter your existing six (6) digit code one time.
➂Enter your NEW six (6) digit code two times.
④If a mistake is made wait thirty (30) seconds and repeat
steps ➀- ➂.
➄Test lock operation several times before closing the door.
●Valid Code Entry - Double signal after valid six (6) digit
code is entered.
●Invalid Code Entry - Triple signal and old code is still valid.
ADD USER
ALWAYS PERFORM THIS OPERATION WITH
THE DOOR OPEN
➀Enter Manager code and HOLD DOWN LAST DIGIT of
CODE until the lock signals with two sets of double beeps.
➁PRESS 1. Lock signals twice.
➂Enter user code twice. The lock signals twice after each
valid entry.
④If a mistake is made wait thirty (30) seconds and repeat
steps ➀- ➂.
●Valid Code Entry - Double signal after valid six (6) digit
code is entered.
●Invalid Code Entry - Triple signal and old code is still valid.
DISABLE USER
ALWAYS PERFORM THIS OPERATION WITH
THE DOOR OPEN
➀Enter Manager code and HOLD DOWN LAST DIGIT of
CODE until the lock signals with two sets of double beeps.
➁PRESS 2. Lock signals once.
➂User is temporarily disabled.
④If a mistake is made wait thirty (30) seconds and repeat
steps ➀- ➂.
●Valid Code Entry - Double signal after valid six (6) digit
code is entered.
●Invalid Code Entry - Triple signal and old code is still valid.
FEATURES
MANAGER CODE (Factory set to 1-2-3-4-5-6)
●Add/Remove User
●Enable/Disable User
USER CODE
●Open Lock
●Change Code
WRONG TRY PENALTY
●Four (4) consecutive invalid codes initiates five
minute delay period.
LOW BATTERY WARNING
●Repeated audio and visual signal (LED flashing and
repeated beeping) during opening indicates battery low.
AUDIO AND VISUAL SIGNAL
●Double signal (LED flashes and unit beeps) indicates
entry is valid or accepted.
●Triple signal indicates invalid or not accepted.
©copyright 2003 12-219V1 LA GARD INC - A MASCO COMPANY
MANAGER PROGRAMMING
Suggested Keypads
3710 Angular Input
3000 Round Entry 3900 LGACCESS
Handle

REINSTATE USER
ALWAYS PERFORM THIS OPERATION WITH THE DOOR OPEN
➀Enter Manager code and HOLD DOWN LAST DIGIT of CODE until the lock signals with two sets of double beeps.
➁PRESS 1. Lock signals once.
➂User is reinstated.
④If a mistake is made wait thirty (30) seconds and repeat steps ➀- ➂.
●Valid Code Entry - Double signal after valid six (6) digit code is entered.
●Invalid Code Entry - Triple signal and old code is still valid.
REMOVE USER
ALWAYS PERFORM THIS OPERATION WITH THE DOOR OPEN
➀Enter Manager code and HOLD DOWN LAST DIGIT of CODE until the lock signals with two sets of double beeps.
➁PRESS 3. Lock signals once.
➂User is permanently removed.
④If a mistake is made wait thirty (30) seconds and repeat steps ➀- ➂.
●Valid Code Entry - Double signal after valid six (6) digit code is entered.
●Invalid Code Entry - Triple signal and old code is still valid.
WRONG TRY PENALTY
●Entry of four (4) consecutive invalid codes starts a 5-minute delay period.
- LED flashes red at ten (10) second intervals.
●At the end of the delay period, two more consecutive invalid codes will restart an additional 5-minute delay period.
Entry will not respond to a single keystroke during delay period.
BATTERY LOW WARNING
●Repeated beeping during an opening indicates that the battery is low and needs immediate replacement.
●Uses one (1) 9-Volt Alkaline Battery. LA GARD recommends the use of Duracell™ or Eveready™
Alkaline batteries. LA GARD recommends the replacement of batteries at least once annually.
If battery is depleted and will not allow lock to open, simply follow instructions below. Lock
contains a non-volatile memory, even with batteries removed the lock will retain all programming.
CHANGING YOUR BATTERY (3710 Angular Input)
Note: Some manufacturers use a small screw to secure the battery compartment cover to the keypad
housing. If your model has this screw, it must be removed first before following the steps listed below.
➀Remove black plastic battery compartment cover (located at the bottom of the keypad) by gently
pulling downward on it’s handle.
➁Allow the battery and it’s attached leads to drop down and out of the battery compartment. If it
does not drop, gently pull on the battery until it does.
➂The connector is easily removed by unsnapping it from the two terminals on the top of the battery.
Never Pull on the Battery Leads
④Connect a new 9-Volt Alkaline battery to the battery clip.
➄Push the battery and the leads completely up into the battery compartment.
➅Install the battery cover by placing one side of the cover in position and then pressing
the other side into position with your finger.
CHANGING YOUR BATTERY (3000 Round Entry)
➀Slide the keypad housing up and carefully pull away from mounting
surface to expose battery compartment.
➁Remove one (1) 9-Volt Alkaline battery and replace with new one.
➂The connector is easily removed by unsnapping it from the two terminals
on the top of the battery.
CAUTION! Hold onto battery terminal cap to avoid pulling wires
out of housing.
④Repeat procedure for second battery.
➄Carefully position the keypad over the mounting screws and slide the
keypad housing down. Ensure that there are no wires or cables trapped
between the input pad and the safe door. Pinched cables can result in
a short circuit.
3000 Round Entry
3710 Angular Input
©copyright 2003 12-219V1 LA GARD INC - A MASCO COMPANY