MasterKraft DA006 User manual

DA006

6
7
8
9
15
16
17

─ 3 ─
Important Safety Instructions
Before beginning any fitness program, you should obtain a complete
physical examination from your physician. When using exercise equipment,
basic precautions should always be taken, including the following:
* Read all instructions before using the equipment. These instructions are
written to ensure your safety and to protect the unit.
* Do not allow children on or near the equipment.
* Use the equipment only for its intended purpose as described in this
guide. Do not use accessory attachments that are not recommended by
the manufacturer: such attachments might cause injuries.
* Wear proper exercise clothing and shoes for your workout----no loose
clothing.
* Be careful when getting on or off the equipment.
* Do not overexert yourself or work to exhaustion.
* If you feel any pain or abnormal symptoms, stop your workout immediately
and consult your physician.
* Never operate the unit when it has been dropped or damaged.
* Never drop or insert anything into any opening in the equipment.
* Always check the unit and its cables before each use. Make sure that all
fasteners and cables are secure and in good working condition.
* Frayed or worn cables can be dangerous and may cause injury.
Periodically check these cables for any indication of wear.
* Keep hands, limbs, loose clothing and long hair well out of the way of
moving parts.
* Do not attempt to lift more weight than you can control safely.
* Do not use the equipment outdoors.
Personal Safety During Assembly
* Read each step in the assembly instructions and follow the steps in
sequence. Do not skip ahead. If you skip ahead, you may learn later that
you have to disassemble components and that you may have damaged
the equipment.
* Assemble and operate the equipment on a solid, level surface. Locate the
unit a few feet from walls or furniture to provide easy access. The
equipment is designed for your enjoyment. By following these precautions
and using common sense, you will have many safe and pleasurable hours
of healthful exercise with the equipment.

Instructions
Before beginning assembly please take the time to read instructions
thoroughly. Please use the various lists in this manual to make sure that all
parts have been included in your shipment. When ordering, use part number
and description from the lists. Use only our replacement part when servicing.
Failure to do so will void your warranty and could result in personal injury.
The equipment is designed to provide the smoothest, most effective
exercise motion possible. After assembly, you should check all functions to
ensure correct operation. If you experience problems, first recheck the
assembly instructions to locate any possible errors made during assembly. If
you are unable to correct the problem, call your authorized dealer. Be sure to
have your serial number and this manual when calling. When all parts have
been accounted for, continue on.
Tools Required
Ratchet Wrench and Socket
Adjustable Wrench
Rubber Mallet
Hex Key Wrench Set
─ 4 ─

Item No. Description Qty
Item No.
Description Qty
1 Weight Stack Frame 1 36 4.5" Pulley 3
2 Cross Brace 1 37 Bushing 2
3 Main Frame 1 38 Bearing Φ50.8*Φ25.4*15.9 2
4 Top Cross Brace 1 39 Flat Head Hex Rivet Nuts M10*19.5 4
5 Arm Bracket 1 40 Hex Head Bolt M12*35 4
6 Hand Bracket 1 41 Flat Washer φ13*φ24*1.5 11
7 Seat Pad Support 1 42 Nylon lock Nut M12 7
8 Main Bracket 1 43 Flat Head Cap Screw M10*25 2
9 Flange 2 44 Flat Head Cap Screw M10*20 1
10 Adjustable Support 1 45 Hex Head Bolt M10*130 4
11 Counter Poise Block 1 46 Hex Head Bolt M10*125 2
12 Arm Pad 1 47 Hex Head Bolt M10*95 2
13 Location ring 1 48 Hex Head Bolt M10*80 1
14 Locking ring 1 49 Hex Head Bolt M10*75 2
15 Main Shaft 1 50 Hex Head Bolt M10*50 2
16 Grip 2 51 Hex Head Bolt M10*30 8
17 Big Aluminous Cap φ60*φ10.5*10 1 52 Hex Head Bolt M10*20 6
18 Seat Pad 1 53 Flat Washer φ11*φ20*2 44
19 Frontal Shroud 1 54 Nylon lock Nut M10 17
20 Back Shroud 1 55
Socket Head Cap Screw M8*50
2
21 L Bracket 2 56
Socket Head Cap Screw M8*30
1
22 Cable 1 57 Button Head Cap Screw M8*45 1
23 Sleeve 2 58 Flat Washer φ9*φ16*1.6 2
24 Aluminium Grip Ring 2 59 Nylon lock Nut M8 3
25 Aluminium Grip Cap 2 60 Socket Set Screw M8*10 6
26 Guide Rod 2 61 Button Head Cap Screw M6*12 2
27 Fixing Sleeve 2 62 Hex Nut M6 2
28 Aluminium Cap φ50*8 2 63 Cross Recess Pan Head Screw 4
29 Plastic Tube Guide 2 64 Flat Washer φ10*φ5.3*1 4
65 Socket Set Screw M5*3 8
31 Top Shroud 1 66
Socket Head Cap Screw M4*15
1
32 Rubber Foot 4 67 Weight Plate 5KG 15
33 Plug RT50*100 1 68 Top Plate 1
34 Spring 1 69 Selector Pin W/Coil 1
35 Spacer 1 70
Weight Rubber Bumperφ63.5*φ19*25.4
2

4
6
3
6
3
63 6
3
64
6
4
64 6
1
3
9
1
2
52 5
0
2
3
53 5
3
53 5
4
54 5
3
53 5
4
54 5
2
1
3
53 5
1
51 5
3
53 5
1
51 5
5
45 4
3
53 5
8
1
1
6
2
6
3
53 5
1
5
71
5
2
6
1
6
2
3
3
53 5
5
45 4
2
3
3
3
3
9
2
0
1
9
58
58 5
4
3
7
5
6
5
3
53 5
4
54 5
3
53 5
4
54 5
2
4
54 5
3
53 5
2
32 3
1
3
53 5
7
47 4
3
53 5
2
52 5
3
53 56
46 4
1
41 41 4
2
42 42 4
6
16 1
5
65 6
5
65 6
4
24 25
65 65
2
6
4
4
7
1
4
1
3
1
7
3
7
3
3
53 53
53 5
4
54 5
9
49 4
3
53 5
4
54 5
5
65 6
5
25
6
26 2
5
55 5
9
5
7
2
9
5
0
60 6
7
2
6
6
3
53 5
2
52 5
1
1
4
3
5
3
5
1
5
1
5
0
60 6
2
4
8
3
2
4
1
4
1
4
9
8
2
3
4
0
4
1
4
0
4
1
4
3
5
0
5
6
3
4
5
2
42 4
1
41 4
5
3
9
8
4
5
3
5
3
2
4
5
0
53
5
8
21
4
3
4
0
4
0
4
1
2
6
3
3
2
1
2
3
5
8
4
8
6
7
6
0
70 7
9
6
6

7

8

STEP 1
1.Attach the Bottom Cross Brace(#2) to the Main Frame (#3) using:
two M10*130 HHB (#45) four φ11*φ20*2 Flat Washer (#53)
two M10 Nylon lock Nut (#54)
2.Attach the Top Cross Brace(#4) to the Main Frame (#3) using:
two M10*130 HHB (#45) four φ11*φ20*2 Flat Washer (#53)
two M10 Nylon lock Nut (#54)
3.Attach the Bottom Cross Brace(#2) to the Top Cross Brace(#4) using:
two M10*75 HHB (#49) four φ11*φ20*2 Flat Washer (#53)
two M10 Nylon lock Nut (#54)
4.Attach the Seat Pad Support (#7) to the Main Frame (#3) using:
one M8*30 SHCS (#56)
9
5353
5454
5353
4949
5353
5454
2
5454
5353
5353
4545
7
3
5353
4545
4
56

6060
6060
5454
2
5454
5353
4242
9
4040
43
28
4141
5
4242
4141
9
28
4141
4040
43
4646
5353
4747
5353
414141
424242
8
1
41
41
15
5353
STEP 2
1.Attach the Main Bracket (#8)to the Weight Stack Frame (#1) using:
three φ13*φ24*1.5 Flat Washer (#41) three M12 Nylon lock Nut (#42)
2.Attach one Flange (#9) to the Bottom Cross Brace (#2) using:
two M12*35 HHB (#40) four φ13*φ24*1.5 Flat Washer (#41)
two M12 Nylon lock Nut (#42)
3.Attach another Flange (#9) to the Bottom Cross Brace (#2) using:
two M12*35 HHB (#40) four φ13*φ24*1.5 Flat Washer (#41)
two M12 Nylon lock Nut (#42)
4.Attach the Arm Bracket (#5) to the two Flanges (#9) using:
two M10*25 Flat Head Cap Screw (#43) two φ50*8 Aluminium Cap (#28)
one φ25.4*284 Main Shaft (#15) four M8*10 Socket Set Screw (#60)
5.Attach the Bottom Cross Brace (#2) to the Weight Stack Frame (#1) using:
two M10*125 HHB (#46) two M10*95 HHB (#47)
10

168
69 67
70
6060
5555
59
59
27
27
2626
STEP 3
1.Attach:
two Guide Rod (#26) two φ63.5*25.4 Weight Rubber Bumper (#70)
fifteen SYD-JZJ 5KG （#67） one Top Plate （#68）
to the Weight Stack Frame (#1) using:
two Fixing Sleeve (#27) two M8*50 SHCS (#55)
two M8 Nylon lock Nut (#59) two M8*10 Socket Set Screw (#60)
2.Attach the Selector Pin W/Coil (#69) to the Top Plate （#68）
11

5
22
36
36
36
66
50 53 53 54
5454
23 53
53
48
50 53 21
53 21 23
1
68
STEP 4
1.Attach the Cable (#22) to the Top Plate (#68).
2.Attach three 4.5" Pulley (#36) to the Weight Stack Frame (#1) using:
two L Bracket (#21) two φ20*φ16*19.3 Sleeve (#23)
two M10*50 HHB (#44) one M10*80 HHB (#48)
six φ11*φ20*2 Flat Washer (#53) three M10 Nylon lock Nut (#54)
3.Attach the Cable (#22) to the Arm Bracket (#5) using:
one M4*15 SHCS (#66)
NOTE:Wrench Tighten Bolts and Nylon Lock Nuts.
12

STEP 5
1.Attach the Seat Pad (#18) to the Seat Pad Support (#7) using:
two M10*30 HHB (#51) two φ11*φ20*2 Flat Washer (#53)
2.Attach the Arm Pad (#12) to the Main Frame (#3) using:
four M10*30 HHB (#51) four φ11*φ20*2 Flat Washer (#53)
3.Attach the Counter Poise Block (#11) to the Arm Bracket (#5) using:
two M10*30 HHB (#51) two φ11*φ20*2 Flat Washer (#53)
NOTE:Wrench Tighten Bolts and Nylon Lock Nuts.
13
12
11
5151
5353
5151
5353
53
5151
53
18
5151
5353
7
3
5

STEP 6
1.Attach the Front Shroud (#19) to the Weight Stack Frame (#1) using:
four M10*20 HHB (#52) four φ11*φ20*2 Flat Washer (#53)
2.Attach the Rear Shroud (#20) to the Weight Stack Frame (#1) using:
two M10*20 HHB (#52) six φ11*φ20*2 Flat Washer (#53)
four M10 Nylon lock Nut (#54)
3.Attach the Top Shroud (#31) to the Weight Stack Frame (#1) using:
four M5*12 BHCS (#63) four φ10*φ5.3*1 Flat Washer (#64)
NOTE:Wrench Tighten Bolts and Nylon Lock Nuts.
14
63 6363 63
64 646464
31
1
20
5252
5353
5454
5353
5454
5353
53
52
52
53
53
5252 53
19

15

16

17