Mastervolt 77010600 Instruction Manual

Components included
Head unit Surface
mount bezel
Bayonet collar
MasterBus cable*
(6m / 20ft)
MasterBus Terminator*
4 × Phillips
countersunk
self-tapping
screws (2.9×16)
If you are not knowledgeable about electrical
systems, have an electrical professional install this
unit.
WARNING
The SmartRemote is not waterproof. Do not install
where the display is exposed to water.
CAUTION
The Mastervolt product warranty covers the
SmartRemote for the first two years after the
purchase date.
The warranty is limited to the cost of repair and/or
replacement of the product. Costs of labor or
shipping are not covered by this warranty.
Mastervolt cannot accept liability for damage due to
the misuse of the SmartRemote.
Warranty
Contact your local waste disposal depart-
ment to properly dispose of the unit.
EUROPE, MIDDLE EAST & AFRICA
Snijdersbergweg 93
1105 AN AMSTERDAM
The Netherlands
[phone]
[email protected]
ASIA/PACIFIC
42 Apollo Drive, Rosedale
AUCKLAND 0632
New Zealand
+ 64 9 415 7261
[email protected]
AMERICAS & CARIBBEAN
N86 W12500 Westbrook Crossing
Menomonee Falls, WISCONSIN 53051
USA
[phone]
[email protected]
Correct Disposal
On first use
Operation Notes
For additional information, like supported devices,
please visit our website: www.mastervolt.com
Specifications
Meaning of the icons
Mastervolt CZone Drop Cable*
(1m / 3.3ft)
SmartRemote
QuickStart Installation Guide
*Need to be ordered separately with OEM packaging
10000015712/04
P1 P2 P3
Model:
Product code retail:
Product code OEM:
Dimensions:
Screen:
Weight:
Operating temperature:
Relative humidity:
Storage temperature:
Power supply:
Power consumption:
Protection degree:
Approvals:
Interfaces:
SmartRemote
77010600
77010500
72×72×30 mm/2.8×2.8×1.2"
320x240 pixels,
16 bits color, 2.8"
75 g / 0.2 lb
-20 to 55°C/-4 to 131°F
max. 95% non-condensing
-30 to 70°C/-22 to 158°F
bus powered, 11-14V *
<180mW (idle mode)
IP20
CE
MasterBus,
CZone (upcoming)
To download this guide in other languages,
please visit our website: www.mastervolt.com
*The paired device must have MasterBus
powering set to on.
Device state (inverting/charging/standby)
Battery voltage or charging current
Output power (AC OUT)
Shore power (AC IN)
Energy left in battery (State of Charge)
Time remaining during discharge
When the SmartRemote is added to a MasterBus
network, it will scan for available supported
devices to pair with. If there is only one device, it
will automatically pair with this device. If there are
multiple devices, it will ask to select a device.
The three push buttons P1, P2 and P3 provide a
scroll and select function. Their behavior depends
on the paired device. When idle, the button menu
slides down. To get it back, press any button.
To wake up from standby mode, simultaneously
press P1 and P3 to enter the main menu. Standby
time can be changed.
How to switch an inverter e.g. on or off?
When the SmartRemote is active, press any key to
reveal the sub menu. Press P1 to switch on or off.
How to adjust the power sharing level?
When the SmartRemote is active, press any key to
reveal the sub menu. Press P2 or P3 to select the
required AC IN limit.
How to select another device?
First, unpair the currently paired device:
simultaneously press P1 and P3 to enter the main
menu. Scroll down to Unpair device and press the
checkmark button. Confirm the action by pressing
the checkmark button again. The SmartRemote
will scan for available devices. If there is only one
device, it will automatically pair with this device. If
there are multiple devices, it will ask to select a
device.
When changing the
language, be aware
that language of the
SmartRemote and
language of the
paired device are two
separate settings!

72mm [2.8"]
Mounting Template
72mm [2.8"]
55mm [2.3"]
Ø 52mm [2"]
62mm [2.4"]
Surface Mount
Mounting
Substrate
Head
Unit
Front Panel
Network
Cables
• Before installing, be sure to turn electrical
power off.
• The SmartRemote is designed for indoor
use only.
• Make sure the front panel is easy
accessible and readable.
• Always check for existing wiring, pipes, etc.
before drilling or cutting into walls.
• Make sure there is adequate space behind
the mounting surface to fit the
SmartRemote, including its cables.
• The SmartRemote is powered by the
MasterBus network. Make sure that at least
one device has MasterBus powering on.
Installation Notes
360 Panel Mount
Note that this requires the 360 Panel Mounting Kit
PN 1525 (sold separately).
STEP 1
Snap header and footer into the mounting clips
on the panel frame. Snap the bezel mount into
place with the flat edge up.
Ensure that the network is properly terminated.
CZone network wiring
MasterBus network wiring
SmartRemote
Back Side
Connect the required RJ45 cable at the back of
the SmartRemote.
STEP 3
Place the SmartRemote and fasten with the
bayonet collar. Turn collar until is snaps.
To remove the front cover, gently insert a small
screwdriver in the opening at the bottom.
30mm [1.2"]
11mm [0.4"]
STEP 2
Place the carrier mount behind the panel, aligning
mounting holes, and attach with 4 screws.
Head
Unit
Bayonet
Collar
Front
Panel
Network
Cables
Carrier MountPanel Frame
Bezel
Mount
Footer
Header