Matrix DSS532 User manual

Thank you for choosing DSS532!
Please read this guide for correct installation and retain it for future reference.
The information in this guide was current at the time of publication. All
specifications are subject to change without notice.
This Guide is meant to help you install and connect the DSS532 as the Key
Expansion Module for EON510 or SPARSH VP510 phone .
Copyright
All rights reserved. No part of this document may be copied or reproduced in any form or by
any means without the prior written consent of Matrix Comsec Pvt. Ltd.
Warranty
Limited Warranty. Valid only if primary protection is provided, mains supply is within limit and
protected, and environment conditions maintained within product specifications. Complete
warranty statement is available on our website: www.MatrixTeleSol.com
Know Your DSS532
IN
OUT
1
Front View Back View
What Your Package Contains
 DSS532
 RJ11 Cable
 Foot Stand
 DSS Extender
 4 Clamps (2 DSS-Phone Clamps and 2 DSS-DSS Clamps)
 Warranty Card Set
 Quick Installation Guide (printed copy)
Installing DSS532
Attach the DSS Extender
 To attach the DSS532 with the phone use the DSS Extender.
 Place the DSS Extender as illustrated below.
Attach the DSS532 with Phone
Step 1
 Turn the phone upside down on a table.
 Now, place the inverted DSS532 adjacent to the phone.
AUX
 Insert the hooks on the Extender into the slots provided on the phone and the
DSS532.
 Firmly slide the DSS Extender upward to lock them in place.
AUX
AUX
DSS Key
DSS Key Label
Slot
IN Port
OUT Port
AUX
AUX
AUX
DSS532 Clamps
DSS-Phone Clamps
Attach this side
to the First DSS
Attach this side
to the Phone
DSS-DSS Clamps
Attach this side
to the Second DSS
Attach this side
to the First DSS
Attach the Clamps
Remove the screws to attach the clamps.
Place the DSS-Phone Clamps between the DSS532 and the phone.
Insert the screws back to fix the clamps.
AUX
Upper DSS-Phone Clamp
Lower DSS-Phone Clamp

Installing Multiple DSS532*
MATRIX COMSEC PVT. LTD.
Head Office
394-GIDC, Makarpura, Vadodara - 390010, India
Ph:[phone]
E-mail: Suppor[email protected]
www.MatrixTeleSol.com
Version 1, November 2016
4. 5. 6.
Connect the DSS532 with Phone*
Step 2
* You can also connect DSS532 with EON510 instead of SPARSH VP510.
Note: Make sure that the DSS532 and phone are mounted at the same angle.
Remove the Foot Stand of attached DSS532
Firmly slide the Foot Stand of the attached DSS532 downward to unlock.
Now, slide down the attached DSS Extender in downward direction.
Step 1
Step 1 Attach the second DSS532 with phone
Attach the second DSS Extender
Place another inverted DSS532 adjacent to the existing assembly.
Place the DSS Extender as illustrated in the diagram below.
Insert the hooks on the Extender into the slots provided on both the DSS532.
Firmly slide both the DSS Extenders upward consecutively (attach the second
extender first followed by the existing one attached to the phone) and lock them
in place.
Connect the second DSS532 to the existing assembly
Step 2
Plug one end of the RJ11 Cable into the OUT Port of the existing DSS532
(already connected with the phone) and the other end into the IN Port of the
second DSS532.
Plug one end of the RJ11 Cable into the Auxiliary Port of the phone and the
other end into the IN Port of the DSS532.
* You can connect a maximum of four DSS532 with the phone.
AUX
IN
OUT
IN
OUT
RJ11 Cable
IN
OUT
OUT
AUX
RJ11 Cable
IN
AUX
IN
OUT
RJ11 Cable
IN
AUX
Attach the Clamps
Attach the DSS-DSS Clamps between both the DSS532.
Attach the Foot Stand
Attach the Foot Stand of both the DSS532.
Note: Make sure that both the DSS532 and the phone are mounted at the same angle.
Attach the Foot Stand
 You can mount the DSS532 with the phone on the desk at two angles - 45
degrees or 55 degrees by attaching the Foot Stand.
Stand attached at
45 degree angle
Stand attached at
55 degree angle
AUX
IN
OUT
IN
OUT
RJ11 Cable
RJ11 Cable
Phone
First DSS
Second DSS
RJ11 Cable
AUX
Phone
First DSS
AUX AUX