MAV 1008 User manual
INSTALLATION and REMOVAL INSTRUCTIONS
Locking Assembly MAV 1008
ENERAL RECOMMENDATIONS and WARNIN S
•Before installing or handling this product, read instruc+ons carefully and completely. Due to possible danger to
persons or machinery resul+ng from improper use of this product, it is very important to follow correct
procedures. Proper installa+on, maintenance and opera+on procedures must be observed. All instruc+ons
included in this manual must be followed carefully. Handling, installa+on and removal of this product must be
done by skilled personnel, familiar with the product, the applica+on and all hazards involved.
•Suitable safety devices should be provided and applicable safety rules should be observed as specified in safety
codes. Those are neither the responsibility of MAV S.p.A., nor are provided by MAV S.p.A.
•Contraven+on of install and safety instruc+ons will void all claims under warranty.
•During storage or handling opera+ons, use only tested and approved handling and/or li4ing tools. Make always
sure that components of Locking Assembly are secured against slipping, falling or rolling.
•Prior to ini+a+ng installa+on or removal procedures, check to ensure that no loads are ac+ng on Locking
Assembly, sha4 or any connected component. Motor and drive train must be switched off and secured against
accidental ac+va+on.
ENERAL INFORMATION
• !"#$#%&!'!(
(!($%$%!
)!$(%"%*%+(,%%$#
%-("#%!.*("%&$!'
!(
/#!%#,%!!(!'!(
•($"%#"0.12
◦"%%!(%0&%%(%,3&%%"4,31
◦%!(%0&%%(%,3&%%"4,31
◦(%0&%%(%,563&(%%"5,5431
◦%"%!&/785694
:"3
•(#;(#(%&%!screws, locking rings, sha4 and hub contact areas coated with a film of
mineral or synthe+c-base oil&%!&%%"#0. %#((%&
(%(%,#%1DON'T USE low fric+on lubricants
$((!!%%!(0$%<= 7<
(%1
•!'!(%2!,>,
•!'!((".!2??@
•)!%%+(;(#(%!%.#!%%+(01)!%%+(
$ ( ( % 9A 0, (# $ 5B1 (# " #!% %+( %
#(#""(#(
•'%#%%(($%$% !#!%%+('+(%!
#>&"%!&$(#(C%%##/
%!%!"&#!%%+(
:"3
;D#
INSTALLATION
SAFETY NOTICE
Prior to ini+a+ng the installa+on procedure, check to ensure that no loads are ac+ng on Locking Assembly, sha4 or
any connected component. Motor and drive train must be switched off and secured against accidental ac+va+on.
($"%#
7!(%!(% (%!%%!(%%%!%
)!(%%$"%!!%!(%!#$%!!%!"%
%!(%&!%!%!(%!%!!%!(%
E(#!%"$,%"!(%%!'$(
(%!%&!'!(%%%&%!."
For ease of installa+on, thrust rings shall be disengaged0.1&$%&%!%(F%!%"
!#!%%%%&&%%!(! G%!!%!"%%!(%%%%&&
%%!(! G%!!%!(%!%!"%%!(%
/%$%%!!(%%%!!'(%!%%%
#+( Thrust rings and outer ring shall be completely supported by sha4 respec+vely hub
bore0.1%%!%%%!&(%%!%!(%
/%#%!(&%!!(+("&H%&%!(%!(0.1
:"3
; E% " %!(%
#"$
5 )!%%!&$!&-%#&%!&%%4I,%%%%!
"%%!(%0.1(#.*&%!!'!(%%
!%$&!(%!%!(+((%Be:er centering of hub from
the beginning of installa+on is essen+al for be:er centering when installa+on is completed.
3 J%+(&!%,3B!!%!.#!%%+(01(&%!
(Progressively +ghten the screws in a crosswise pa:ern (fig. 3), using approx. ¼ turns for several passes(#
K%(!7%%&%!&%%4I,%%%F&C%%%
!#!%&
9 7#$%+(""&)!+(%%"$% %,#"%!
& #!% " & & &$ , C% & L%!(% %+( $
("&(%!.#!%%+(
6 %%!%+(&! %.#!%%+(01(&%!(!
&%!&(%&+()!%#%&
%("(%!%!&%%98#!%(%(%!%("C%
%%M(!
=8)N2"#(C%%%!(&%!(%(((! G
%!!(($$%%&%!.
:5"3
;N,"#!%-
REMOVAL
SAFETY NOTICE
Prior to ini+a+ng the removal procedure, check to ensure that no loads are ac+ng on Locking Assembly, sha4 or any
connected component. Motor and drive train must be switched off and secured against accidental ac+va+on.
Some locking screws will be used for removal. The user shall make sure that the end +p of these screws is ground flat
and chamfered%%%%!%!&%!"(! G%!!
7&&%!(M%!"#%(%!"$
N(%!%,%""%%!(%O$"O%%%&
(%!%(! G%!!#
&$%&%!%(F%!%"&%(! G#$%!!%!"%
%!(%Progressively +ghten these screws in a crosswise pa:ern, using approx. ¼ turns for several passes (#
%!"%%!(%0.517%%&%!&%%4I,%%%F&C%%%
!#!%&
%!&#%!%!(%F%!%!"%%!(%
)"&%(! G%!!%!(% Progressively +ghten these screws in a
crosswise pa:ern, using approx. ¼ turns for several passes(#%!%!(%0.317%%&%!
&%%4I,%%%F&C%%%!#!%&
:3"3
;5""%%!(% ;3"%!(%
Table of contents
Other MAV Lock manuals
