Max Burton 6960 User manual

Max Burton®150W Ceramic Heater & Fan #6960
IMPORTANT SAFEGUARDS
Read all instructions before operating•
Do not immerse cord or plug in water or other liquids•
Do not let cord hang over edge of table or counter•
Do not position upside down•
Do not use for anything other than its intended use•
Do not put any objects in front of the heater or block openings when in•
use
Donotuseheaternearammablematerials•
Do not use outdoors•
Do not insert foreign objects into any opening•
Do not install where it could obstruct safe vehicle operation or visibility•
Never install on or near vehicle air bags•
Heater becomes very hot. Do not touch hot surfaces•
Unplug when not in use and before cleaning•
There are no serviceable parts. Do not open unit.•
Allow unit to cool before storing•
To avoid electric shock and injury, do not use near infants or anyone•
incapable of disconnecting without assistance
Donotuseinareaswhereammableliquidsareusedorstored•
Administer close supervision when using around children•
This unit will not shut off automatically. Turn off immediately after use.•
PARTS IDENTIFICATION
MOUNTING
There are two mounting options available - screws or hook & loop tape:
Select an area on the dashboard or other secure surface that is 2-3 feet1.
from the driver and passengers.
Hook & Loop Tape Option: Remove the backing and attach the hook2.
side to the bottom of the mounting base and the loop side to the
dashboard.
Screw Option: Remove the mounting base from the unit by gently sliding3.
it away from the body. Mark the location of the two mounting holes in
the base and drill using a 4mm drill bit. Secure with the included screws.
Return the unit to the base.
OPERATION
Caution: Due to the high wattage required to operate the Heater, the engine
must be running at all times to avoid damage to the vehicle battery, plug or
unit. When using with a 12V power supply, it must be rated at 15 amp - 150
watts or higher.
For best results, use the heater when inside vehicle temperatures are above
32ºF. Using in colder temperatures will result in less heat output.
Make sure the POWER SWITCH is in the OFF position and the engine is1.
running before inserting the 12-VOLT PLUG into, or unplugging from, a
power source.
Keep the engine running during operation. The LED power indicator will2. illuminate showing power is provided to the unit. If LED is not illuminated
repair the vehicle’s power system before using.
Select either HEAT or FAN operation.3.
Adjusttheairowbytiltingtheunitupordown.4.
The unit may be used with our 200 watt Converter #6993 to allow it to5.
plug into any 120V electrical outlet. Available from your local retailer or
www.aervoe.com.
CLEANING
Unplug before cleaning.1.
Dust regularly. Clean the with damp cloth and dry with a clean soft cloth.2.
Do not immerse.
TROUBLESHOOTING
If the 12-volt circuit fails to operate, try the following suggestions:
Unplug from the power supply an make sure that the receptacle is1.
clean. DO NOT USE METAL TOOLS. If cleaning is needed, use only
insulators, such as wood.
Check the plug’s fuse. Carefully unscrew the plug’s top section. Remove2.
and check the fuse with the proper electronic meter. If defective, replace
withcorrectfuse(seespecicationfortype).Alsocheckthevehicle’s
fuse panel.
Some cigarette lighters have a separate circuit breaker located directly3.
behind the cigarette lighter receptacle. If you lighter is not working, this
circuit breaker may have blown and could require replacement. Consult
your vehicle owner’s manual for replacement.
12-V Plug
Power Indicator LED
Mounting Base
Tilt Adjust
Power Switch
Heat/Off/Fan
Air Outlet

150W CeramiC heater & fan
OPERATING INSTRUCTIONS
SPECIFICATIONS
POWER SOURCE 12V DC
POWER CONSUMPTION 10.5A/150W
FUSE 250V 20A glass fuse
HEATING ELEMENT PTC Ceramic
MAX TEMPERATURE 104°F(40°C)
POWER CORD 6 ft.
WEIGHT 1lb.(0.45kg)
DIMENSIONS 6.5” x 5.5” x 2”
AERVOE INDUSTRIES, INC.
Gardnerville,NV89410•1-800-227-0196
www.aervoe.com•[email protected]
6960inst; cs3/11