MAXDATA PLATINIUM 9000-4R User manual

MAXDATA Platinum 9000-4R Server
User‘s Manual

2 MAXDATA PLATINUM Server 90004R
3Table of Contents

2 MAXDATA PLATINUM Server 90004R
3Table of Contents
Table of Contents
Safety Precautions 5
Safety Steps ............................................................................................................................................5
1 Specifications and Disclaimers 7
Declaration of the Manufacturer .............................................................................................................8
Safety Compliance ..................................................................................................................................8
FCC Electromagnetic Compatibility Notice (USA) ...................................................................................9
FCC Declaration of Conformity................................................................................................................9
Laser Compliance Notice ........................................................................................................................9
Electromagnetic Compatibility Notices (International)...........................................................................10
Europe (CE Declaration of Conformity) ............................................................................................10
Japan EMC Compatibility ................................................................................................................10
ICES-003 (Canada)............................................................................................................................10
BSMI (Taiwan) ..................................................................................................................................10
2 Setting up the system 11
Removing the Server from the Box.......................................................................................................11
Selecting a Site......................................................................................................................................11
Checking Power Cords..........................................................................................................................12
Connections and Controls .....................................................................................................................13
Connecting the Monitor, Keyboard, and Mouse ...................................................................................16
Powering On the Server for the First Time ...........................................................................................16
Mounting the LS240 Device..................................................................................................................17
The Maxdata Platinum 9000-4R Resource CD ......................................................................................17
The Maxdata Platinum 9000-4R Server System Product Guide............................................................18
Figures
1. Platinum 9000-4R Server....................................................................................................................7
2. Chassis Front View ........................................................................................................................... 13
3. Peripheral Bay Module...................................................................................................................... 13
4. Front Panel View ............................................................................................................................... 14
5. Chassis Back Features...................................................................................................................... 15
Tables
1. Platinum 9000-4R Server Physical Specications............................................................................7
2. Front Panel Control and Indicator Description ...............................................................................14

4 MAXDATA PLATINUM Server 90004R

5Safety Precautions
Safety Precautions
The Following safety symbols are used in this manual:
Warning
Failure to follow these guidelines may result in personal
injury or even death
Caution
Failure to follow these guidelines may result in damage
to the system or its components
 Note General usage tips
Warnings
The power supply in this product contains no user-serviceable parts. There may be more than one
supply in this product. Refer servicing only to qualified personnel.
Do not attempt to modify or use the supplied AC power cord if it is not the exact type required. A
product might be equipped with more than one AC power cord.
The power button on the system does not turn off all system AC power. To remove all AC power
from the system, you must unplug each AC power cord from the wall outlet or power supply.
To avoid injury from electrical and mechanical hazards, chassis covers should only be removed by
qualified service personnel.
Safety Steps
Whenever you remove the chassis covers to access the inside of the system, follow these steps:
1. Turn off all peripheral devices connected to the system.
2. Turn off the system by pressing the power button.
3. Unplug all AC power cords from the system or from wall outlets.
4. Label and disconnect all telecommunication cables and all other cables connected to I/O
connectors or ports on the back of the system.
5. Provide some electrostatic discharge (ESD) protection by wearing an anti-static wrist strap
attached to chassis ground of the system—any unpainted metal surface—when handling
components.
6. Do not operate the system with the chassis covers removed.
After you have completed the six safety steps above, remove the covers as follows:
1. To open the top back cover, push the sliding latches on the top of the cover and pull the
cover toward the back of the chassis.
2. To remove the top back cover, continue to slide the cover toward the back of the chassis
until it reaches the end-stops. Press the latch on the left rail slide and pull the cover until it
clears the chassis.
3. To remove the top front cover, loosen the two captive screws on either side of the cover,
slide the cover toward the front of the chassis until it stops, then lift the cover off.
4. Always replace the covers before operating the system.

6 MAXDATA PLATINUM Server 90004R
Caution
For proper cooling and airflow, unless hot swapping PCI cards or fans, always reinstall the chassis
covers before turning on the system. Operating the system without the covers in place can
damage system parts. To install the covers:
1. Check first to make sure you have not left loose tools or parts inside the system.
2. Check that cables, add-in boards, and other components are properly installed.
3. To replace the top back cover, slide the two bearing cages on the back top cover all the way
to the end of the slides.
4. Place the top cover on the cover slides and push the cover into place.
5. To replace the top front cover, attach the back edge of the front top cover to the chassis,
lower the front edge of the cover onto the chassis, then push the cover into place.
6. Tighten the two captive screws on either side of the cover.
7. Connect all external cables and the AC power cord(s) to the system.
Warning
A microprocessor and heat sink might be hot if the system has been running. Also, there might
be sharp pins and edges on some board and chassis parts. Contact should be made with care.
Consider wearing protective gloves.
Warning
Danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent
type recommended by the equipment manufacturer. Discard used batteries according to manufac-
turer’s instructions.
The system is designed to operate in a typical office environment. Choose a site that is:
• Clean and free of airborne particles (other than normal room dust).
• Well-ventilated and away from sources of heat including direct sunlight.
• Away from sources of vibration or physical shock.
• Isolated from strong electromagnetic fields produced by electrical devices.
• Protected when in regions that are susceptible to electrical storms. We recommend you
plug your system into a surge suppresser and disconnect telecommunication lines to your
modem during an electrical storm.
• Provided with a properly grounded wall outlet.
• Provided with sufficient space to access the power supply cords, because they serve as the
product’s main power disconnect.
Warning
Servers can be too heavy for a single person to lift or move safely. Depending on the server, use
two people or a mechanical assist to lift or move the server.

7Specifications and Disclaimers
1 Specifications and Disclaimers
Server Specifications
Table 1. Platinum 9000-4R Server Physical Specifications
Characteristic Specication
Height 178 mm (6.9 inches, 4U)
Width 445 mm (17.5 inches)
Depth 711 mm (28.0 inches)
Weight (max.) 48 kg (106 lbs.)
Required front
clearance
76 mm cm (3 inches)
Required rear clearance 152 mm (6 inches)
Required side clearance 25 mm (1 inch)
Heat Dissipation 1500 W (5,100 BTU/hr)
The system weight listed above is an estimate for a fully configured system and will vary depending
on number of peripheral devices and add-in cards as well as the number of processors and DIMMs
installed in the system.
Figure 1. Platinum 9000-4R Server
WARNING
Use all four handles for a minimum two-person lift. Serious personal injury can take place when lif-
ting the product that can, when fully configured, weigh as much as 106 lbs (48 kg).

8 MAXDATA PLATINUM Server 90004R
9Specifications and Disclaimers
Declaration of the Manufacturer
We hereby certify that this product is in compliance with European Union EMC Directive 89/336/EEC,
using standards EN55022 (Class A) and EN55024 and Low Voltage Directive 73/23/EEC, Standard
EN60950.
Safety Compliance
USA UL 1950 – 3rd Edition/CSA 22.2. No. 950-M93
Canada UL certified – 3rd Edition/CSA 22.2. No. 950-M93 for Canada (product
bears the single UL mark for U.S. and Canada)
Europe Low Voltage Directive, 73/23/EECTUV/GS to EN60950 2nd Edition with
Amendments, A1 = A2 + A3 + A4
International TUV/CB to IEC 60950 3rd Edition TUV/CB - EN60 950 2nd Edition +
Amendment 1-4TUV/CB - EMKO-TSE (74-SEC) 207/94 plus international
deviations
Australian / New Zealand CB Report to IEC 60950, 3rd Edition plus Australian deviations
Electromagnetic Compatibility (EMC)
USA: FCC CFR 47 Part 2 and 15, Verified Class A Limit
Canada: IC ICES-003 Class A Limit
Europe: EMC Directive, 89/336/EEC
• EN55022, Class A Limit, Radiated & Conducted Emissions
• EN55024, ITE Specific Immunity Standard
• EN61000-4-2, ESD Immunity (Level 2 Contact Discharge, Level 3 Air
Discharge)
• EN61000-4-3, Radiated Immunity (Level 2)
• EN61000-4-4, Electrical Fast Transient (Level 2)
• EN61000-4-5, AC Surge
• EN61000-4-6, Conducted RF
• EN61000-4-8, Power Frequency Magnetic Fields
• EN61000-4-11, Voltage Dips and Interrupts
• EN61000-3-2, Limit for Harmonic Current Emissions
• EN61000-3-3, Voltage Flicker
Japan: VCCI Class A ITE (CISPR 22, Class A Limit) IEC 1000-3-2 Limit for Harmonic
Current Emissions
Australia/New Zealand: AS/NZS 3548, Class A
Taiwan: BSMI Approval, Class A
Korea: RRL Approval, Class A
Russia: GOST Approved
International: CISPR 22, Class A Limit

8 MAXDATA PLATINUM Server 90004R
9Specifications and Disclaimers
FCC Electromagnetic Compatibility Notice (USA)
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operating in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause harmful interference. In this case, the user
is required to correct the interference at their own expense. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on; the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the grantee of this device could void the
user’s authority to operate the equipment. The customer is responsible for ensuring compliance of
the modified product.
FCC Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
For questions related to the EMC performance of this product, contact your local reseller.
Laser Compliance Notice
Maxdata products that use laser technology comply with Class 1 laser requirements.
Class 1 Laser Product
Luokan 1 Laserlaite
Klasse 1 Laser Apparat
Laser Klasse 1
 NOTE
Class A device definition: If a Class A device is installed within this system, then the system is to
be considered a Class A system. In this configuration, operation of this equipment in a residential
area is likely to cause harmful interference.

10 MAXDATA PLATINUM Server 90004R
Electromagnetic Compatibility Notices (International)
Europe (CE Declaration of Conformity)
This product has been tested in accordance too, and complies with the Low Voltage Directive (73/23/
EEC) and EMC Directive (89/336/EEC). The product has been marked with the CE Mark to illustrate
its compliance.
Japan EMC Compatibility
This is a Class A product based on the standard of the Voluntary Control Council for Interference by
Information Technology Equipment (VCCI). If this equipment is used in a domestic environment,
radio disturbance may arise. When such trouble occurs, the user may be required to take corrective
actions.
ICES-003 (Canada)
Cet appareil numérique respecte les limites bruits radioélectriques applicables aux appareils numériques
de Classe A prescrites dans la norme sur le matériel brouilleur: “Appareils Numériques”, NMB-003
édictée par le Ministre Canadian des Communications.
English translation of the notice above:
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus
set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the
Canadian Department of Communications.
BSMI (Taiwan)
The BSMI Certification number and warning is located on the product safety label which is located
visibly on the external chassis.