MaxLite QuadroMAX QM Series User manual

QuadroMAX
LED Outdoor Lighting ixtures
Installation Manual
QM Series
REV: 3/01/16

QuadroMAX LED Fixture
BEFORE YOU BEGIN
Read these instructions completely and care ully.
WARNING
Risk of fire or electric shock. Luminaire wiring and electrical parts may be damaged
when drilling for installation of led retrofit kit, check for enclosed wiring and components.
To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or
other sharp objects.
General Safety Information
• To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts,
cuts/abrasions, and other hazards read all warnings and instructions included with and on the fixture
box and all fixture labels.
• Before installing, servicing, or performing routine maintenance upon this equipment, follow these
general precautions.
• Commercial installation, service and maintenance of luminaires should be performed by a qualified
licensed electrician.
• or Residential installation: If you are unsure about the installation or maintenance of the luminaires,
consult a qualified licensed electrician and check your local electrical code.
• DO NOT INSTALL DAMAGED PRODUCT!
• This fixture is intended to be connected to a properly installed and grounded UL listed junction box.
WARNING:
RISK OF ELECTRICAL SHOCK
• Turn off the power when you perform any maintenance.
• Verify that supply voltage is correct by comparing it with the luminaire label information.
• Make all electrical and grounded connections in accordance with the National Electrical Code and
any applicable local code requirements.
• All wiring connections should be capped with UL approved wire connectors.
CA TION:
RISK OF INJ RY
• Wear gloves and safety glasses at all times when removing luminaire from carton, installing, servicing or perform-
ing maintenance.
• Avoid direct eye exposure to the light source while it is on.
• Account for small parts and destroy packing material, as these may be hazardous to children.
CA TION:
RISK OF FIRE
• Keep combustible and other materials that can burn away from luminaire and lamp/lens.
• MIN 90°C SUPPLY CONDUCTORS.
Illustrations in the manual are for installation purposes only. It may not be identical to the fixture purchased.

General Wiring Diagram:
CA TION: Turn off electrical power at fuse or circuit breaker box before wiring fixture to the
power supply.
120-277V Wiring:
1.) Connect the black fixture wire to the (+) LINE supply wire.
2.) Connect the white fixture wire to the (-) COMMON supply wire.
3.) Connect the green fixture wire to supply ground wire.
0-10V Dimmable Wiring:
1.) Connect the black fixture wire to the HOT LINE supply wire.
2.) Connect the white fixture wire to the NEUTRAL supply wire.
3.) Connect the green fixture wire to supply ground wire.
4.) Connect the purple fixture wire to the (V+) DIM wire.
5.) Connect the gray fixture wire to the (V-) DIM wire.
QuadroMAX LED Fixture

Trunnion Swivel (TS)
1.) Secure Trunnion to Quadromax by tightening (2) 5/16-18 Internal HEX Head bolts with split washers.
2.) Adjust angle of fixture to desired position by loosen (2) pivot bolts and angle locking screws.
3.) Swivel the fixture to design angle.
4.) Tighten the Pivot Bolts and Angle Locking Screw.
QuadroMAX LED Fixture

Fixed Sur ace (FS)
1.) Secure Wall Mount Bracket to Quadromax by tightening (2) 5/16-18 Internal HEX Head bolts
with split washers and gasket.
2.) Orient Wall Mount Box and TOP position must be pointed up.
3.) Secure Wall Mount Box to a Sturdy Mounting Surface.
4.) Apply silicone sealant and seal the gap between wall and wall mount box Gasket and / Or Junction
box if needed.
5.) Wire the fixture using UL listed wire connectors
6.) Placed wired fixture over the Wall Mount Box and tighten the (2) 3/8-16 Internal HEX Head bolts
with split washers.
7.) Check and make sure Gasket was compressed.
8.) Tighten ½” NPS plug and apply silicone sealant to all unused conduit entry points.
QuadroMAX LED Fixture

Knuckle Sur ace (KS)
1.) Secure Wall Mount Bracket to Quadromax by tightening (2) 5/16-18 Internal HEX Head bolts with
split washers and gasket.
2.) Orient Wall Mount Box and TOP position must be pointed up.
3.) Secure Wall Mount Box to a Sturdy Mounting Surface.
4.) Apply silicone sealant and seal the gap between wall and wall mount box Gasket and / Or Junction
box if needed.
5.) Wire the fixture using UL listed wire connectors
6.) Placed wired fixture over the Wall Mount Box and tighten the (2) 3/8-16 Internal HEX Head bolts
with split washers.
7.) Check and make sure Gasket was compressed.
8.) Adjust wall mount to desired angle by Loosening center bolt and adjusting accordingly.
9.) Tighten ½” NPS plug and apply silicone sealant to all unused conduit entry points.
QuadroMAX LED Fixture

Wall Pack (WP)
1.) Secure Wall Mount Bracket to Quadromax by tightening (2) 5/16-18 Internal HEX Head bolts with
split washers and gasket.
2.) Secure Wall Mount Bracket to Wall Junction box.
3.) Wire the fixture using UL listed wire connectors.
4.) Placed wired fixture over the Wall Mount Box and tighten the (2) 5/16-18 set screws.
QuadroMAX LED Fixture

Pole Mount (PM)
1.) Secure Pole Mount Bracket to Quadromax by tightening (2) 5/16-18 Internal HEX Head bolts with
split washers and gasket.
2.) or 4” Round Pole: Secure fixture to round pole by tightening (2) 3/8” X1.75” bolts with flat and split
washer.
3.) or Square pole: Insert Wedge between pole and Arm bracket and Secure fixture to round pole by
tightening (2) 3/8” X1.75” bolts with flat and split washer.
4.) Wire the fixture using UL listed water proof wire connectors.
QuadroMAX LED Fixture

QuadroMAX LED Fixture
Pole Mount Drilling Template:
(template shown to scale.)

Slip itter Knuckle (SK)
1.) Secure Slipfitter to Quadromax by tightening (2) 5/16-18 Internal HEX Head bolts with split washers
and gasket.
2.) Wire the fixture using UL listed water proof wire connectors.
3.) Slip slipfitter onto Tenon and secure by tightening set screws with Allen key.
(The slipfitter mounting fits a 2 3/8” O.D Tenon.)
4.) Adjust slipfitter to desired angle by adjusting the pivot bolt and rotating arm.
QuadroMAX LED Fixture

Slip itter Fixed (SF)
1.) Secure rigid area mount bracket to Quadromax by tightening (2) 5/16-18 Internal HEX Head bolts
with split washers and gasket.
2.) Wire the fixture using UL listed water proof wire connectors.
3.) Slip Rigid area mount bracket onto Tenon and secure by tightening set screws with Allen key.
(The slipfitter mounting fits a 2 3/8” O.D Tenon.)
QuadroMAX LED Fixture

Canopy (CP)
1.) Secure bottom bracket to Quadromax by tightening (6) #10 screws with flat and split washer.
2.) Secure Top bracket to ceiling junction box by tightening (4) #10 screws with flat and split washer.
3.) Wire the fixture using UL listed wire connectors.
4.) Insert bottom bracket onto top bracket and secure the fixture by tightening (2) ¼” screw.
QuadroMAX LED Fixture

QuadroMAX LED Fixture
Mounting Options: Dimensions
Trunnion Swivel (TS) Fixed Sur ace (FS)
Knuckle Sur ace (KS) Wall Pack (WP)

QuadroMAX LED Fixture
Mounting Options: Dimensions
Pole Mount (PM) Slip itter Knuckle (SK)
Slip itter Fixed (SF) Canopy (CP)

MaxLite LED Outdoor Fixture Limited Warranty
LIMITED WARRANTY OR CERTAIN MAXLITE® LED LIGHTING IXTURES, SPECI ICALLY WALL PACKS; LOOD LIGHT;
AREA LIGHT; CANOPY; GARAGE; PARKING; SECURTIY LIGHT; VAPOR TIGHT AND ROADWAY.
This limited warranty is provided by the MaxLite company described below ("Seller") to you as the original purchaser of the
LED lighting product that is identified on Seller's invoice reflecting its original purchase (the "Product"). The Seller is the
MaxLite Company identified as such on the invoice. This limited warranty may be transferred to subsequent purchasers of the
Product, provided that such Product is resold in new condition and in its original packaging. Seller warrants that the Product,
when delivered in new condition and in its original packaging, will be free of defects in material and workmanship for a period
of IVE (5) YEARS from the date of original purchase or the number of hours used has not exceeded the L70 life stated for
each LED fixture. The determination of whether the Product is defective shall be made by Seller in its sole discretion with
consideration given to the overall performance of the Product. A Product shall not be considered defective solely as a result
of the failure of individual LED components to emit light if the number of inoperable components is less than 10% of the total
number of LED components in the Product.
If Seller determines the Product is defective, Seller will elect, in its sole discretion, to refund you the purchase price of the
Product, repair the Product or replace the Product. This limited warranty does not apply to loss or damage to the Product
caused by: negligence; abuse; misuse; mishandling; improper installation, storage or maintenance; damage due to fire or
acts of God; vandalism; civil disturbances; power surges; improper power supply; electrical current fluctuations; corrosive
environment installations; induced vibration; harmonic oscillation or resonance associated with movement of air currents
around the Product; alteration; accident; failure to follow installation, operating, maintenance or environmental instructions
prescribed by Seller or applicable electrical codes; or improper service of the Product performed by someone other than
Seller or its authorized service provider. This limited warranty excludes field labor and service charges related to the repair
| or replacement of the Product. THIS LIMITED WARRANTY IS VOID I THE PRODUCT IS NOT USED OR THE
PURPOSE OR WHICH IT IS DESIGNED.
Seller reserves the right to utilize new, reconditioned, refurbished, repaired or remanufactured products or parts in the
warranty repair or replacement process. Such products and parts will be comparable in function and performance to an
original product or part, as determined by Seller in its sole discretion, and warranted for the remainder of the original
warranty period.
In order to make a warranty claim, you must notify Seller in writing within sixty (60) days after your discovery of the defect,
provide proof of purchase such as the invoice and comply with Seller's other warranty requirements. Upon receiving that
notice, Seller may require you to promptly return the Product to Seller, or its authorized service provider, freight prepaid.
Your warranty claim should be addressed to MaxLite, Inc., 12 York Ave. West Caldwell NJ 07006.
This limited warranty only applies to specified LED fixtures. Backup batteries, photocells, mounting accessories and other
fixture accessories can be found at www.MaxLite.com/lighting/products/warranty.
THE OREGOING WARRANTY PROVISIONS ARE EXCLUSIVE AND ARE GIVEN AND ACCEPTED IN LIEU O ANY AND
ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION ANY WARRANTY
AGAINST IN RINGEMENT AND ANY IMPLIED WARRANTIES O MERCHANTABILITY OR ITNESS OR A PARTICULAR
PURPOSE.
IN NO EVENT SHALL SELLER BE LIABLE OR INCIDENTAL, COMPENSATORY, CONSEQUENTIAL, INDIRECT,
SPECIAL OR OTHER DAMAGES. SELLER'S AGGREGATE LIABILITY WITH RESPECT TO A DE ECTIVE PRODUCT
SHALL IN ANY EVENT BE LIMITED TO THE MONIES PAID TO SELLER OR THAT DE ECTIVE PRODUCT.
This warranty is effective for purchases of Product on or after the effective date set forth below. Seller reserves the right to
modify this warranty from time to time. Any modification of this warranty shall be effective for all orders placed with Seller on
or after the effective date of such revised warranty.’
Effective Date: May 12, 2014
QuadroMAX LED Fixture